C) In a cylinder-piston arrangement shown (D₁ = 100 mm), the piston is moving downwards at Vp = 0.5 mm/s, and as it does, the water flows outward through the side orifice (D₂ = 10 mm) of the cylinder to fill the tank (D3 = 50 mm) state below it. Determine the rate at which the depth z of the water in the down tank is changing.

C) In a cylinder-piston arrangement shown (D₁ = 100 mm), the piston is moving downwards at Vp = 0.5 mm/s, and as it does, the water flows outward through the side orifice (D₂ = 10 mm) of the cylinder to fill the tank (D3 = 50 mm) state below it. Determine the rate at which the depth z of the water in the down tank is changing.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. An orifice in the side of a vertical tank discharges oil (sp. gr. = 0.82) under a head of 4.0 m. and 25 KPa pressure acting on the surface of the oil. If the diameter of the orifice is 5 cm, the coefficient of contraction is 0.62, and the head lost on the orifice is 45 cm, determine the discharge, coefficient of velocity, and the coefficient of discharge.
With the chamber-pipe system in the figure, the ideal fluid (water) taken from the infinitely sized chamber A is poured into the atmosphere with a 40 cm fixed diameter BCDEF pipe. Since zB=29, zC=10, zD=28.5, zE=5 and zF=28 meters according to the comparison plane;a) Calculate the flow of the system.b) Draw the relative load (energy) and piezometer lines of the system.c) Determine where the greatest pressure will be observed throughout the system and calculate its relative value.
A 90% efficient pump lifts water from a lower reservoir a shown in the figure. The head loss in the 150mm pipe is 3 times the velocity head in that pipe and the head loss in the 100mm pipe is 20 timew the velocity head in that pipe. A.If the desired flow rate is 20L/s ehat shoukd be the powet input of the pump in Kw? Choices: 42.9,28.8,32.0,38.6 B.Compute the pressure head, in m of water, at the suction line before the pump Choices: 12.39,10.29,9.74,7.56 C.Compute the pressure head,in m of water, at the discharge line right after the pump. Choices: 156.26,136.80,139.53,145.20
A pump draws water from reservoir A and lifts it to reservoir B as shown in Figure below. The loss of head from A to 1 is equal to the velocity head in the 150-mm pipe and the loss of head from 2 to B is 15 times the velocity head in the 100-mm pipe. Determine the horsepower output of the pump and the pressure heads at 1and 2 when the velocity of flowing water at the 150 mm diameter pipe is 1.5 m/s.
A pipe carrying oil of sp gr 0 877 changes in A pipe carrying oil of sp gr 0.877 changes in size from 150mm at section E to 450mm at section R Section E is 3 66m lower than R section R. Section E is 3.66m lower than R and the pressures are 91.0kPa and 60.3kPa, respectively. If the discharge is 0.146m3 respectively. If the discharge is 0.146m /s, determine the lost head and the direction of flow.
An 83-mm-diameter siphon is drawing oil (SG = 0.85) from an oil reservoir, as shown in the figure. If the velocity of flow in the pipe is 'v', the head loss from point 1 to point 2 is 6v2/2g, and the head loss from point 2 to point 3 is 2v2/2g. Find the absolute pressure (in kPa) at point 2. Use atmospheric pressure, Patm = 102 kPa. Use y1 = 5 m., and y2 = 7 m.
Water at 20°C flows through a 300-mm-diameter pipe that discharg sphere as shown in Figure 4.61, When a partially open val the top of the pipe, the flow rate in the pipe is 0.2 m*s and the (gauge) pressure just upstream of the valve is 600 kPa. Estimate the force partially open valve, es into the atmo- ve extends 200 mm from exerted by the water on the —Valve 0.2 mYs —» Atmosphere Figure
A cylindrical tank, filled with water and axis vertical, is open at one end and closed at the other end. The tank has a diameter of 1.2m and a height of 3.6m. It is then rotated about its vertical axis with an angular speed w. a. Determine w in rpm so that one third of the volume of water inside the cylinder is spilled. b. Determine the largest pressure developed in the tank.
For a vertical rectangular gate, one side has linseed oil (0.938) and the other has two fluids - castor oil (0.96) and water. Considerinh a unit-width of the gate, apoly the PRESSURE PRISM CONCEPT (Illustrate and label the pressure diagram/prism) to calculate the magnitude and direction of the following when z = 20ft.
The flowrate of the flow is 0.20 + a/10 m3 /s in a pipe placed on a horizontal plane. The pipe diameters are D1= 0.30 m and D2= 0.20. Please find the force acting to the pipe by the flow. The gauge pressure at (1) is p1 =200 + b*10 kN/m2 . (g=9,81 m/s2, g=10kN/m3 ) a= 4 b=3
Water at 20°C ( ρ= 999.7 kg/m3 and μ=9.7720 x10-4 kg/m · s) is flowing steadily in a hexagonal cross sectional pipe b=1.5cm, 20-m-long at an average velocity of 1.2 m/s. Determine: (a) Hydraulic diameter. (b) The pressure drop. (c) The head loss. (d) The pumping power requirement to overcome this pressure drop.
3.Water flows from a tank through 22 meters of 150–mmdiameter pipe and then discharges into air as shown in the figure. The flow of water in the pipe is 120 L/s.Assume n = 0.013 and neglect minor losses. a. Find the velocity of flow in the pipe in m/s. b. Determine the total head loss in the pipe in meters. c. Calculate the pressure at the top of the tank in kPa.