Question 110 PointsThe two bars, pinned together at B, are supported by a frictionless surface at A and built-in support at C. Determine the internalmoment acting on section 1.+ 0.6 m -- 0.6 m - 0.6 m 0.6 m-...900 N/m50°ВA 162 N• m126 N. m261 N. m612 N. m

as support A is producing reaction at an angle. tha'ts why there is horizontal and vertical both…

Answered: Question 1 10 Points The two bars,…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the embedment length of the tension bar around the area of the supporting column. Let h=500mm b= 300mm
Calculate and draw the internal forces created at H section of the bracket beam? a = 500 mm b= 200 mm Px= 15 Kn Py=0 Kn Pz = 10 Kn
Calculate V(x) and M(x) between x = 2ft and x = 7ft (measured from the left end) of thebeam below: Ay = +1865 # (upwards) and MA = +3765 ft#(counter-clockwise); the support reaction at the roller C is Cy = +675 # (upwards). There isa HINGE at B, with internal forces bx = 0 and by = ±175 #.
Compute the value of EI ϴ at the right end support. Wo = 19 kN/m, P =5 kN, L1 = 1.2m, L2 = 2.1m, L3 = 2.4m
.15 2.16 The three forces acting on the beam can be replaced with a single equivalent force R. Determine the angle θ and R. 25kN P2 60 kN P3 80 kN 40° 50° 4 m 6 Figure P2.16 COMPANY
Determine the following unknowns on the beam shown below using Area-Moment Method. Consider 150 mm x150 mm section and E = 80 GPa. Show complete and organized solution. a. Vertical Reaction at B in kN. b.Moment Reaction at A in kN-m. c. Deflection at point C in mm. d. Deflection at midspan of AB in mm. Given: a- 7m b- 24kN/m C- 30kN
The length of the 3/32 in.diameter steel wire CD has been adjusted so that with no load applied, a gap of 1/16 in. exists between the end B of the rigid beam ACB and a contact point E. Knowing that E=29 X 10⁶ psi, determine where a 50-lb block should be placed on the beam in order to cause contact between B and E.
Determine the tension at AC. A. 55.23 kN B. 52.53 kN C. 32.55 kN D. 25.35 kN
AB, a rectangular (0.6 mx0.9 m) sluice gate, blocks a liquid with a gravity of 0.79. The weight of the floodgate is 300 N, and find the force that must be applied to the Cable BCD to open the surface Please tell me the process of solving
A vertical rectangular gate 2m wide and3 m high is submerged in water with its top edge flushedWith the water surface. Find thefollowing: 1. The value of the maximum force, F acting oncenter of pressure2. The value of the eccentricity3. The location of Force. F below the watersurface4. The magnitude of the maximum pressure
The bent bar shown is subjected to 3 forces shown. Replace these forces with an equivalent couple M and single force F at point A. Show solution to answers M = 21.8 kN-m, cw Fv = 12.03 kN, D FH = 1.60 kN, R
A concrete cube 60 cm on each edge (sp. gr. 2.40) rests on the bottom of a tank in which sea water stands to a depth of 5 m. The bottom edges of the block and sealed off so that no water is admitted under the block. Find the vertical pull required to lift the block. Note: The answer should be 13.76 kN or near.

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Question 1 10 Points The two bars, pinned together at B, are supported by a frictionless surface at A and built-in support at C. Determine the internal moment acting on section 1. 0.6 m 0.6 m 0.6 m - 0.6 m ... 1900 N/m 50° B