Question 1-A: The steel framework is used to support the reinforced stone concrete slab that is used for lobbies of offices. The slab is 130 mm thick. Sketch the loading and reactions that acts along members BE and FED. Then find the loads of column F. Take, L1= 4 m L2 = 6 m. Hint: Take Dead Loads and Live Loads are equal to 10 Kn/m2. 4 m 6 m 4 m

Question 1-A: The steel framework is used to support the reinforced stone concrete slab that is used for lobbies of offices. The slab is 130 mm thick. Sketch the loading and reactions that acts along members BE and FED. Then find the loads of column F. Take, L1= 4 m L2 = 6 m. Hint: Take Dead Loads and Live Loads are equal to 10 Kn/m2. 4 m 6 m 4 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the frame shown, determine the support reactions. EI is constant.Use the force method. I have a correct answer, it is: VA = 36.30 kN (↑); HA = 19.30 kN (→); VB = 18.70 kN (↑); HB = 11.30 kN (←). To the left); B (right). I don't know how to get to this result, please show me how to get there step by step
A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 15,000 ksi] rods, and a solid steel [E = 30,000 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.500 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.360 in. If all bars are unstressed before the load P is applied, determine the normal force in steel rod (2) after a load of P = 36 kips is applied.
The frame (Figure 1) has dimensions H1 = 4 m , H2 = 3 m , and L1 = 6 m , and supports two lateral loads P1 = 10 kN and P2 = 12 kN . The area of column AE is 40 cm2 and the area of column BF is 80 cm2 . a) Use the cantilever method to determine the axial force at G. Gy = ? b) What is the horizontal reaction from the ground on the base of the column at A? Let a positive reaction be pointing to the left. Ax = ? c) What is the horizontal reaction from the ground on the base of the column at B? Let a positive reaction be pointing to the left. Bx = ?
Refer to the beam loaded as shown. (a)What is the Value of horizontal reaction at the fixed support?(b)What is the value of resulting couple at A?
F=30 kN single load, M=34 kN.m moment and w=10 kN/m distributed load are acting on the beam whose loading condition is given in the figure. Point B is located just to the right of the application point of force F and moment M. The length L is also given as L=5 m. According to this;Question1-A) Find the support response (Dy) at point D. (Write your result in kN.)Question1-B) Find the support response (Ay) at point A. (Write your result in kN.)Question1-C) Find the shear force (VB) at point B. (Write your result in kN.)
FORCE METHOD An overhang beam ABC is loaded as shown. Determine the reactions at the supports due to loading and a support settlement of 1 mm at the roller B. Take E = 200 GPa and I = 500(10^6) mm^4.
Using Conjugate-Beam Method. Consider 250 mm x 250 mm section and E = 200 GPa. a=4.5 b=26 c=10 Determine: Vertical Reaction at C in kN. Moment Reaction at C in kN-m.
In the overhanging beam show, determine P so that the moment over each support equals the moment at the midspan. W= 3.7 kN/m. Round your answer to 2 decimal places.
Q9c. For the beam below, the point loads and distances are as follows: F1 = 11. 25 kN, F2 = 11.25 kN and F3 = 4.50 kN L1 = 2.25 m, L2 = 4.50 m, L3 = 4.50 m and L4 = 2.25 m Determine the bending moment at D. Give your answer in kilonewton metres (kNm) to two decimal places.
P1 = 445 N P2 = 501 N Determine the force in member DC, use a positive value for tension or a negative for compression
Determine the force in each member of the structure and establish whether the members are in tension or compression. Establish P1= 45 KN, P2= 30 KNSolve the problem considering the following: The force P1 will be the maximum point of a triangularly distributed load with a horizontal distribution of X meters.You must leave the solution in terms of X and show the particular solution when X is equal to 0m and 2m.
Determine the Dead Load on Top Chord of this figure