Question 1: Equilibrium of rigid body The uniform beam AD, which is supported by pin at point A and by roller at point C, carries the loads as shown in the figure below. Neglecting the weight of the beam and considering the system to be at equilibrium, (a) draw the free body diagram of the system (b) determine the reactive force at point C (c) determine the reactive forces at point A. 120 kN/m |--2 m 100 kN B 2 m 120 kN/m 2 m 30⁰ D 120 kN s]

Question 1: Equilibrium of rigid body The uniform beam AD, which is supported by pin at point A and by roller at point C, carries the loads as shown in the figure below. Neglecting the weight of the beam and considering the system to be at equilibrium, (a) draw the free body diagram of the system (b) determine the reactive force at point C (c) determine the reactive forces at point A. 120 kN/m |--2 m 100 kN B 2 m 120 kN/m 2 m 30⁰ D 120 kN s]

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.3.25P: An S6 × 12.5 steel cantilever beam AB is supported by a steel tic rod at B as shown. The tie rod is...

See similar textbooks

Similar questions

Solve Prob. 10.54 assuming that A and B are connected by a spring of stiffness k = 0.3 W/b and free length b.
The overhang beam below is supported by a pin support at A and a roller at B. The weight of the beam is 600 N/m. Draw the Free Body Diagram for this beam and apply the equilibrium equation to find the value of support reactions.
Determine the vertical reaction (A y - kN) and the reactive moment (M A - kN·m) at the support at A considering thestock values: M = 10·a + 30·b + 20·c + 200 {kN·m}, q = 20·(a + b) + 10·c + 100 {kN/m} and F = 30· (a + b+ c) + 50 {kN}. The beams AB and BC of the beam are interconnected by a smooth pin at B. Assume minimum accuracyof 6 significant figures. (a = 7; b=1 ; c=1) Ay= MA=
Given the Statically Determinate Simple Beam as shown below withinternal hinged at Point B and additional external support at Point D (0.9 m fromPoint A). 10N/mDetermine the following:a.) The External Reaction at Point A.b.) The Internal Reaction at Point B.c.) The External Reaction at Point C.d.) The External Reaction at Point D. express in 3 decimal points
The horizontal beam is assumed to be rigid while supporting the distributed load. Determine the angle of inclination of the beam after the load is applied. Each support consists of a wooden post with a diameter of 120 mm and an original length (unloaded) of 1.40 m- Consider E = 12 GPa
The compound beam is supported by a roller at point C, fixed at point A, and the two sections are pinned at point B. It is subjected to a free couple moment M, a distributed load with maximum load intensity w, and a concentrated force F. If the distributed load w = 0.6 kN/m, the concentrated force F = 0.6 kN, and the free couple moment M = 0.8, determine the magnitude of the support reaction (in kN) at pin B. Answer must include 2 places after the decimal point.
S2) The distributed load, which is given as function of q (x) = q0 (2x/3L)2, acts on the ABCbeam given in the figure. The left side of the ABC beam is fixed at A. The weight of the ABCbeam is neglected. Accordingly, find all the reaction forces of beam.Note: In the calculations, the equations available in the tables of the elastic curve cannot beused. In case of using these equations of the elastic curve, the answer will be invalid.
Draw the influence lines for the vertical reactions at supports A and E and the reaction moment at support E of the beam shown in Fig. P8.13.
Considering the structure and loading shown in the figure below, determine the reaction module in A and E, when cos α = 3/5.
The load on a cantilever beam AB has a triangulardistribution with maximum intensity q0 (seefigure). Determine the angle of rotation θB and thedeflection δB at the free end.
The three-bar truss in Fig. a is subjected to a horizontal force of 5 kip. If the cross-sectional area of each member is 0.20 in2, determine the horizontal displacement at point B. E = 29(103) ksi.
Question 1) in FIG loading condition is given beam F force F = 65 kN , first distributed load W 1 = 41 kN / m , w 2 distributed load w 2 = 51 kN / m , θ angle θ = 48 ° and L length of L = 5 m . According to this; Question 1-A) B at the point y direction ( B y ) Determine the support reactions. (Enter yourresultwithout writing kN units.) Question 1-B) to the point in y direction ( A y ) Determine the support reactions. ( Enter yourresult without writing kN units.) Question 1-C) to the point in x direction ( A x ) Determine the support reactions. ( Enter yourresult without writing kN units.)