Answered: Question 1 In a proctor test the…

Question 1 In a proctor test the specimen has a bulk density of 18 kN/m3 and moisture content of 13%. What is the additional moisture content required for saturating the sample. Take G=2.68

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter5: Soil Compaction

Section: Chapter Questions

Problem 5.2P

See similar textbooks

Related questions

Q: 6. The beam shown supports a 15 kN concentrated load at the free end and another 15 kN at point C,…

Q: flow from pipelines A to F is 300 lit/s. Using a friction factor of 0.015 for all pipelines and with…

Q: Draw the shear and moment diagram for the problem

Q: Assume a population of fish grows exponentially. A pond is stocked initially with 500 fish. After 6…

A: Given: Fish at beginning= 500, Fish at 6 months= 1000,

Q: Q3. A pump supplies water at a rate of 4 ft³/s and lifts water to a height of 15 ft. What is the…

Q: Determine the difference in pressure рA - рв between the centers A and B of the closed pipes, which…

A: Given data, Shg = 13.55 Sk = 0.82 Angle = 60 from horizontal.

Q: A line was determined to be 2538.45 m when measured with a 45m tape supported throughout its length…

Q: AI А -3 3m- B 35 CI -3m É 3m D

Q: i) Which of the following statements about a straight horizontal pipe of 6 inch diameter pressurized…

A: This question is related to the Fluid Mechanics from Civil Engineering. This is mcq type question.

Q: Q- On the surface of a thick layered clay soil deposit, a point load of 750 kN is applied at a depth…

A: Given data: Load, Q = 750 kN Depth, z = 3.5 m Radial distance, r = 1.2 m

Q: Fluid Flow in Pipes A 4km long pipeline, 88 cm in diameter connects two fresh water open reservoirs…

Q: 4 col lok 1. W

A: Solution:- Given data:- It as asked to solve external support reactions for given beam.

Q: The tangent thru the PC has a direction due to North; and the tangent through the PT has a bearing…

A: The bearing of the tangent through the PC along the north The bearing of the tangent through the PT…

Q: A drainage basin, or watershed, is defined by the organization and orientation of water flow,…

A: A drainage or watershed is used to collect and store water for different purposes, including…

Q: P A 30 B

Q: If a vertical curve's incoming grade (g₁) is -5%, the outgoing grade (g₂) is 5%, the station at the…

A: Given, g1 = -5% g2 = 5% L = 3000 ft PVI = 25+00 PVI (El) = 450 ft

Q: Poisson Model is used for the segment of a certain highway. Vehicles are recorded at 30-seconds…

A: Poisson Model is used for the segment of a certain highway. Vehicles are recorded at 30-seconds…

Q: A 25m deep bored pile has a shaft of diameter 1m and enlarged base of 2.5m diameter in lower 1.5m…

A: Given data, Adhesion factor = 0.45 FOS = 2.5 Depth of pile = 25 m Shaft diameter = 1m and, Enlarge…

Q: (γ=17kN/m³, kv=1 x 10-2m/day) over 2m

Q: Question- The normal depth in a wide rectangular channel is increased by 10%. The percentage…

Q: Using the method of joints, determine the force in each member of the truss shown. M D TT F 4¹ B E…

Q: Determine the magnitude of the internal shear at point C if P = 68.7 N, Q=49:4N. (Values only, 1 no…

Q: 1. With the given profile level notes, STA BM₂ 0 +00 +10 TP₁ 0 +22 + 30.5 +34.2 +39.3 + 42.5 TP₂ 0…

A: To find the Elevation at BMb and to plot the profile

Q: An oil refinery is located on the north bank of a straight river that is 2km wide. A pipeline is to…

A: Width of the river, B = 2 km The storage tanks are 6 km east of the refinery. The per km cost of…

Q: A submerged stratum of clay has a thickness of 15m. The average water content of samples taken from…

A: Given, w = 54% G = 2.78 Thickness = 15 m

Q: Q2 For the truss shown in the figure:: 4. Determine the force in member fe using the joint method?…

Q: Problem- A 50 cm diameter pipe carries water (v = 0.294 x 106 m²/s) at an average velocity of 10…

A: Given data- Diameter of the pipe d=50 cm=0.50 m, Viscosity- v=0.294×10-4 m2/s, Average velocity…

Q: Question- The normal depth in a wide rectangular channel is increased by 10%. The percentage…

Q: 10kp 10kp 20cm 14cm

A: Given data, 10 kp = 100 N Horizontal distance from load to pin = 20 cm Horizontal distance between…

Q: 1. Why are transportation policy, regulation, and planning important? How do they feed off each…

A: Solution:- It is asked to explain various terms in detail

Q: The modulus of elasticity of concrete (Force/Area) is 13 GN/m^2. Determine its US Customary units…

A: Given, Modulus of elasticity of concrete = 13 GN/m²

Q: Situation #7 Use the cantilever method and determine (approximate the reactions at supports A and B.…

Q: Question- A 5m high vertical earth retaining wall retains a dry granular backfill with O angle of…

Q: A 6 m- B 31 с 3

Q: For the truss shown in the figure, the force in the member QR is

Q: solve the reactions using slope deflection method without settlements

A: Answer Let us first calculate the Fixed End Moments For Span AB Consider A and B are fixed…

Q: Infiltration capacity of a soil is defined as The maximum rate of infiltration into the soil…

A: Using definition of infiltration capacity

Q: Compute for the unknown Line AB BC CD DE EA Distance 300 400 250 350 277.96 Bearing S 37 30 E S 43…

A: Answer We know that when two bearings of a traverse is omitted we need to use a temporary line of…

Q: + Compute for the unknown Line AB BC CD DE EA LINE AB BC CD DE EA Distance 300 400 250 350 277.96…

Q: A three-hinged parabolic arch has a span of 30 m and the central rise is 5 m. It is subjected to a…

A: Given : Span = 30 m Central rise = 5 m Point load = 40 kN at a distance of 20 m from right hinge To…

Q: Hydrostatic Pressure on Submerged Surfaces 1. Determine the moment at A required to hold the gate as…

A: Given: Specific weight of waterγw=9.81 kNm3 Width of the gateb=2 m Depth of the gated=6 m Specific…

Q: A sand is composed of solid constituents having a density of 2.60 Mg/m³. The void ratio is 0.572.…

Q: 3. Find the deflection at the midspan of the beam loaded as shown. The beam supports a uniformly…

A: The given beam is statically determinate beam and can be analyzed using the equations of equilibrium…

Q: 4/ The following is an incomplete page of level book in which X indicates missing Entry line.…

A: Using rise and fall method

Q: Question- A 5m high vertical earth retaining wall retains a dry granular backfill with O angle of…

Q: A concentrated load of 290 kips is applied to the ground surface. Required What is the vertical…

A: Solution is attached below as

Q: Determine the reactions in the fixed end supports assuming El is constant. Use the integration…

A: Given data:

Q: A B Block A supports a pipe colur Knowing that the coefficient of 0.25 and that 0=45°, detern…

Q: Assignment No. 1 1. A simple curve have the following elements: middle ordinate = 2 ma and length of…

Q: Solve the forces at the spring and cable AB in equilibrium. Also, determine the stretched length of…

Concept explainers

Soil Compaction Test

Soil compaction is the major area of geotechnical engineering. Soil is composed of multiple pores present on its surface, while the soil is mainly composed of gravel, sand, rocks, etc. The arrangement of these rocks and gravels is such that they build up voids (spaces) between them, which allows spaces for the roots of the plants and crops to spread and absorb the required amount of nutrients. Soil compaction is a major problem primarily caused by human activities, micro-organisms, and other multiple factors.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 8.81-pound sample is obtained from an excavation with a volume of 0.070 cubic feet. The sample weight 7.63 pounds after drying. Assume a specific gravity of 2.66. Calculate wet unit weight, dry unit weight, void ratio, porosity and degree of saturation.
A 0.67 ft3 sample has a wet weight of 74.4 pounds and moisture content of 33%. The soil is saturated to 90%. Find wet unit weight, dry unit weight, void ratio, porosity and specific gravity.
For a falling laboratory permeability test on a fine sand, the following data are given:Length of specimen = 10 cm.Diameter of specimen = 9.5 cm.Diameter of standpipe = 1.5 cm.Head at time is zero = 50 cmHead at time is 4 min = 25 cmDetermine the seepage velocity in cm/min. Use void ratio = 0.55. Round off to three decimal places.
From the constant head permeability test arrangement shown, the following values are given: Void ratio of specimen = 0.46 Length of Soil Sample = 450mm Constant head difference = 700mm Water collected in a period of 3 min = 0.000354 m3 Cross-sectional Area of Soil Sample = 0.00226 m2 Determine the coefficient permeability in m/hour (Ans: 2.102 m/hr) Compute the discharge of velocity in m/min. (Ans: 0.052 m/min) Compute the seepage velocity in m/min. (Ans: 0.165 m/min)
Given: Weight of wet sand sample (Ww) = 500 g Weight of Dry sand sample (Wd) = 490 g Moisture content of the given sand is: 5% 4% 2% 1%
Subj- civil Q. An undisturbed soil sample that is cylindrical in shape and measures 3 in (76.2 mm) in diameter by 6 in (152.4 mm) in length after oven drying weighs 2.57 lb (1.166 kg bulk) as opposed to 3.04 lb (1.38 kg mass). What are the densities and the weights in (a) wet and dry units? Additionally, find out the moisture content.
Note) For soil sample in Table 2, initial thickness of sample = 14.31 mm, sample area = 2827.433 mm^2, dry weight measured at the end of test = 52.53 g, specific gravity = 2.7 Also, Determine the compression index and expansion index Please show graph
A soil specimen is 38 mm in diameter and 76 mm long, and in itsnatural condition weighs 168 g. When dried completely, thespecimen weighs 130.5 g. The value of GS is 2.73. What is thedegree of saturation of the specimen?
A WET OF SOIL SAMPLE HAS A VOLUME OF 4.85 x 10^-4 m3 AND WEIGHS 8.5N. AFTER OVEN DRYING, THE WEIGHT REDUCES TO 7.5N. IF sg = 2.7DETERMINE THE UNIT WEIGHT. DETERMINE THE MOISTURE CONTENT. DETERMINE THE DEGREE OF SATURATIONAnswer in 4 decimal places with unit
A 443 gram, 42.8 mm diameter by 97 mm long clay specimen was tested in a triaxial test. After failure, the entire specimen was dried to a constant mass of 342 grams. Using either an assumed specific gravity of 2.579 or assuming saturation (whichever is more appropriate), FIND the moisture content (%, 1 decimal place).
Q1. Undisturbed soil sample was collected from the filed in Melbourne in steel tube for laboratory evaluation. The tube has the diameter of 85 mm, length of 170 mm and the moisture weight of 1600 g. If the oven-dried weight was 1200 g and Gs = 2.69, calculate the followings:a) Bulk unit weight (?) in kN/m3b) Field moisture content (w)c) Void ratio & porosity (e and ⴄ) d) Degree of saturation (Sr)
Can u solve ?(readable) A soil specimen is 38 mm in diameter and 76 mm long, and in its natural conditionweighs 168.0 g. When dried completely in an oven, the specimen weighs 130.5 g. The value ofGs is 2.73. What is the degree of saturation of the specimen?