Question 12In the previous problem, you saw that lyd? = 9ft?.Also: 1ft = 144in?, and 1m?10000cm?.We can use these relationships to convert between units in area and volume problems.Suppose you want to convert 342ft yd. Set up the ratios below and multiply them:(3428)(tya")(1)ft?yd?Notice how the ratios are set up so that the units ft“ will cancel (divide) out, and leave the remaining nounor unit as yd?.Similarly, suppose you want to convert 1584in → ft. Set up the ratios below and multiply them:(1n')in)(1584in)lft2(1)ft?Be sure to be careful with the units you work with and use the appropriate conversion ratios. Alwaysinclude the units in vOur calculations and Vou can use them to check the aCcuracy of Vour work!t....mp3 Question 13>Simple US Conversions, Conversion Equations, and Conversion FactorsComplete the table below by finding the equivalent values of the given value in the forms requested.Do not round your results.ConvertConversiomEquationNeeded Conversion FactorConverted Result1 minExample:120 sec1 min = 60 sec2 min to sec60 sec2pt1qt6.9 pints to quartspt =qt1qt2ptqt24hrldaydayhr1day24hrhr3.3 days to hours116ozilblb51.2 ounces to poundsozlb1lb16oz%DQuestion Help: VideoSubmit Question.mp3

Since you have posted multiple questions in this question which are not interlinked so I have solved…

Question 12 <> In the previous problem, you saw that lyd? = 9ft. Also: 1ft? %3D 144in?, and 1m² = 10000cm2. %3D We can use these relationships to convert between units in area and volume problems. Suppose you want to convert 342ft - yd. Set up the ratios below and multiply them: (3428) (1ya") (1) ft yd? Notice how the ratios are set up so that the units ft“ will cancel (divide) out, and leave the remaining noun or unit as yd?. Similarly, suppose you want to convert 1584in → ft. Set up the ratios below and multiply them: (1584in²) (1n°) (1) in") ft2

Question 12 <> In the previous problem, you saw that lyd? = 9ft. Also: 1ft? %3D 144in?, and 1m² = 10000cm2. %3D We can use these relationships to convert between units in area and volume problems. Suppose you want to convert 342ft - yd. Set up the ratios below and multiply them: (3428) (1ya") (1) ft yd? Notice how the ratios are set up so that the units ft“ will cancel (divide) out, and leave the remaining noun or unit as yd?. Similarly, suppose you want to convert 1584in → ft. Set up the ratios below and multiply them: (1584in²) (1n°) (1) in") ft2

Functions and Change: A Modeling Approach to College Algebra (MindTap Course List)

6th Edition

ISBN:9781337111348

Author:Bruce Crauder, Benny Evans, Alan Noell

Publisher:Bruce Crauder, Benny Evans, Alan Noell

ChapterP: Prologue: Calculator Arithmetic

Section: Chapter Questions

Problem 18E: When the Radius Increases a. A rope is wrapped tightly around a wheel with radius of 2 feet. If the...

See similar textbooks

Similar questions

Length A in Figure 205 is 3 inches and length B is 2.5 feet. Determine the ratio of length A to length B in lowest form.
When the Radius Increases a. A rope is wrapped tightly around a wheel with radius of 2 feet. If the radius of the wheel is increased by 1 foot to a radius 3 feet, by how much must the rope be lengthened to fit around the wheel? b. Consider a rope wrapped around the Earths equator. We noted in Exercise 17 that the radius of the Earth is about 4000 miles. That is 21,120,000 feet. Suppose now that rope is to be suspended exactly 1 foot above the equator. By how much must the rope be lengthened to accomplish this? The Size of the Earth The radius of the Earth is approximately 4000 miles. a. How far is it around the equator? Hint: You are looking for the circumference of a circle b. What is the volume of the Earth? Hint: The volume of a sphere of radius r is given by 43r3. b. What is the surface area of the Earth? Hint: The surface area of a sphere of radius r is given by 4r2.
A micrometer reading is made at dimension D on a tapered shaft (Figure 217). For each of the problems use the dimensions given in the table, compute the taper, set up a proportion, and determine diameter C to 3 decimal places.
A plug gage tapers 3.10 mm along a 38.00 mm length, as shown in Figure 215. Set up a proportion and determine the amount of taper in the workpiece for each of the following problems. Express the answers to 2 decimal places.
The block in Figure 13-7 has a threaded hole with a 0.0625-inch pitch. Determine the number of threads for the given depth to 1 decimal place. All dimensions are in inches.
Read the setting on this customary vernier micrometer scale graduated to 0.0001". The vernier, thimble, and barrel scales are shown in flattened view.
Solve the following applied right triangle problems. Compute linear values to 3 decimal places, customary unit angles to the nearer minute, and metric angles to the nearer hundredth degree. 24. Determine dimension x. All dimension are in millimeters. .
Three holes are drilled in the plate shown. All dimensions are in inches. Determine dimensions A and B to 3 decimal places.