QUESTION 2: A class-A emitter follower biased with a constant current source is shown below. Assume circuit parameters of V ¹ = 14 V, V = -14 V, and R₂ = 78 n. The transistor parameters are ß = 69 and VBE(On) = 0.69 V. The minimum current in Q₁ is to be ig₁(min) = 0.044 A and the minimum collector- emitter voltage is to be VCE(min) = 0.64 V. Determine the value of R that will produce the maximum possible output voltage swing. What is the value of Io? What are the maximum and minimum values of iE1? Then calculate n, the power conversion efficiency. Vo(max) (V) Format: 83.29 Format: -36.52 Vo(min) (V) Io (A) Format: 0.5283 R (22) Format: 22.62 İE1 (max) (A) Format: 0.2256 Average Load Power, PL (W) Format: 2.2682 Average Supply Power, Ps (W) Format: 3.0554 Power Conversion Efficiency n (%) Format: 29.3996

QUESTION 2: A class-A emitter follower biased with a constant current source is shown below. Assume circuit parameters of V ¹ = 14 V, V = -14 V, and R₂ = 78 n. The transistor parameters are ß = 69 and VBE(On) = 0.69 V. The minimum current in Q₁ is to be ig₁(min) = 0.044 A and the minimum collector- emitter voltage is to be VCE(min) = 0.64 V. Determine the value of R that will produce the maximum possible output voltage swing. What is the value of Io? What are the maximum and minimum values of iE1? Then calculate n, the power conversion efficiency. Vo(max) (V) Format: 83.29 Format: -36.52 Vo(min) (V) Io (A) Format: 0.5283 R (22) Format: 22.62 İE1 (max) (A) Format: 0.2256 Average Load Power, PL (W) Format: 2.2682 Average Supply Power, Ps (W) Format: 3.0554 Power Conversion Efficiency n (%) Format: 29.3996

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A base voltage of four volts is applied to an NPN bipolar junction transistor. A twenty kilo ohm resistor is linked to the base, while a hundred kilo ohm resistor is connected to the collector. The Collector is powered by a six volt supply voltage. Assume the transistor is in active mode, with a fifty common Emitter current gain(β).(i) Utilize the dc equivalent model of the transistor to draw the circuit design.(ii) Calculate the Collector current (IC) and the Base current (IB) .ii) Locate/determine the result (VCE).
Fixed-bias configuration, Emitter-bias configuration, and Voltage-divider configuration- rank these three configurations based on their provided stability (i.e. ? independency)to the operating point. Use mathematical terms/equations to explain and justify your
Draw, Illustrate and label your schematic diagram before solving the problem. 3) Given an Emitter-Stabilize Biased transistor circuit with beta DC is 250,Base resistor is 150 ohms, collector resistor is 1.5k ohms ,emitter resistor is 500 ohms ,emitter voltage supply is -5v and Voltage at common collector is +28V,Voltage at Base-emitter junction is 0.7v,. Determine Base current, Collector current and Voltage at collector-emitter junction.
Given VTH=1.2 and k=0.5mA/V2, determine the following a) The value of ID, VGS and VDS b) Mode of operation of the MOSFET. (Verify this answer)
The fixed-bias circuit of Figure 1 (a) is the simplest transistor dc bias configuration. The addition of emitter resistor to the dc bias of the BJT provided improved stability as shown in Figure 1 (b), known as emitter-bias configuration. a) Calculate IB , IC and VCE for the given of β = 50 and β = 100 for fixed-bias circuit as shown in Figure 1 (a). b) Repeat question (a) for the emitter-bias circuit as shown in Figure 1 (b). c) Give your comment based on the changes in Ic and VCE for question (a) and (b).
24. For the given circuit, VCC = 17 volts, RB = 500 KΩ,RC =6KΩ,RE =6KΩandβ=120.Assume Transistor is Silicon, VBE=0.7 volts. a. Compute for the base current Q-point, IBQ (in Amperes) b. Compute for the collector current Q-point, ICQ (in Amperes) c. Compute for the collector-to-emitter voltage, VCEQ (in Volts)
1. Use the figure below to solve following questions (a) Solve the following dc quantitiesi. VB(Q1)ii. VE(Q1)iii. IE(Q1)iv. VC(Q1)v. VB(Q2)vi. VE(Q2)vii. IE(Q2)viii. VC(Q2)(b) Suppose that the emitter follower is omitted and the output from thecollector of Q1 is capacitively coupled to the 250Ω load, RL. What isthe output voltage across the 250Ω load?
For the transistor , IS = 4 × 10−16 μA,βF = 75, and βR = 4. (a) Label the collector, base,and emitter terminals of the transistor. (b) What isthe transistor type? (c) Label the emitter-base andcollector-base voltages, and label the normal direction for IE , IC, and IB. (d) Write the simplified formof the transport model equations that apply to thisparticular circuit configuration. Write an expressionfor IE /IB. Write an expression for IE /IC. (e) Findthe values of IE , IC, IB, VC B, and VE B.
Consider the voltage divider circuit for biasing an n-channel E-MOSFET.Given the following quantities: IDON = 3 ma at 10 V; VTH = 5 V; Supply VDD = 40 V;R1 = 22 MΩ, R2 = 18 MΩ, RD = 3 kΩ, Rs = 820 Ω . Determine ID and VDS
Topic: Field Effect Transistor For the given circuit, determine the parameters required in each below: a. Gate Voltage (VG) b. Drain Current (ID) c. Drain-Source Voltage (VDS) d. Gate-Source Voltage (VGS) e. Source Voltage (VS) f. What biasing method was utilized in the circuit? self bias, fixed bias, voltage divider bias, or source feedback bias?
In order to express the effect of the internal capacitors of BJT and the high frequency reception, the current gain expression depending on the frequency (Figure b) (hfe) is used in the case of collector emitter short circuit, voltage source connected at base end and emitter grounded (Figure la).. The catalog information of the 2N2222 transistor is given in Figure Ic. In the catalogue, when Ic=20 mA, it is seen as fT=250 MHz. a) Find the total capacitor effect for the case where gm> > wCμ. (Cpi) + (Cμ) = ?pF
1. Derive the Avf, Rif, Rof, R’of for the circuit shown in figure 1. For each transistor theh-parameters, hie and hfe are equal.