Question # 2: Determine the force in each of the three cables needed to lift the ma that has a weight of 10 KN. 10 kN A 3 m m

Q: Question # 1: The lift sling is used to hoist a container having a mass of 500 kg. Determine the…

A: Solution: m = 500 kg

Q: The picture attached shows a boom that supports the weight 2000 N. The boom is supported by the…

A:

Q: If the mass of cylinder A is 40 kg. determine the mass of cylinder C in order to hold the assembly…

A:

Q: QUESTION 8 The 580 N load is suspended on the cable by a pulley at A. The length of the cable is 1.5…

A:

Q: Q2/ As shown in fig.(2) the crate has a weight of 750 lb. Determine the 1- Draw the Free Body…

A: Given data Weight of crate = 750lb

Q: A gardener uses a 60-N wheelbarrow to transport a 250-N bag of fertilizer. What force must she exert…

A:

Q: Determine the forces on the two members (1) and (2) as shown in .figure below

A: Let F1 be the force in member 1 and F2 be the force in member 2. Apply equilibrium equation of…

Q: Draw a complete and correct free-body diagram of each of the body designated in the statement. The…

A: Given Data: The mass of the uniform bar is, m. The mass of roller is, m0. The couple subjected to…

Q: Determine the force developed in each element of space armor and indicate whether the elements are…

A:

Q: A light rod is being used as a lever as shown. The fulcrum is 1.20 m from the load and 2.40 m from…

A:

Q: Draw FBD at point A and determine the force developed in each cable used to support the 40KN crate…

A:

Q: Q2/ A former student of mechanics wishes to weigh himself but has access only to a scale A with…

A:

Q: the force in member (DF) is equal to.

A:

Q: 5. The machine part of negligible weight is supported by a pin at A and a roller at C. Determine the…

A:

Q: Q2/ A former student of mechanices wishes to weigh himself but has access only to a scale A with…

A:

Q: With what force magnitude T must the person pull on the cable in order to cause the scale A to read…

A:

Q: Determine the force in each cable used to support the 40-lb crate

A: The free body diagram is shown below:

Q: A container of mass m = 120 kg is supported by three cables as shown.

A: Draw a Free-body diagram of Container, Vector AB is represented as, Unit vector of AB is…

Q: Find the force in member BC

A:

Q: Q5-the crate has weight of 550 lb .determine the force in each supporting cable?

A:

Q: The flexible cable shown in Fig. 5 lb/ft. The cable is horizontal at the left support. weighs…

A:

Q: force on the pin from the slot, respectively, are

A: Given. Section modulus of the member is same in both the arms.where,  An L shaped elastic member ABC…

Q: Q2/ A former student of mechanics wishes to weigh himself but has access only to a scale A with…

A:

Q: Q1: The machine part of negligible weight is supported by a pin at A and a roller at C as shown in…

A:

Q: A former student of mechanics wishes to weigh himself but has access only to a scale A with capacity…

A: Find the correct weight of man.

Q: Question #6 If block b has a mass of 35 kg, what is the force in cables AD and AC? What is the mass…

A:

Q: The small piston of a hydraulic lift has a cross-sectional area of ​​4.6 cm2 and its large piston…

A: Given Data⇒cross-sectional area of smaller sectionA1=4.6 cm2=0.00046 m2cross-sectional area of…

Q: 1- The crate has a weight of 550 lb. Determine the force in each supporting cable.

A:

Q: The A-frame is being hoisted into an upright position by the vertical force of 62 lb . (Figure 1)

A: Given data as per the question The magnitude of force F =62 lb finding the position vector along AC…

Q: A former student of mechanics wishes to weigh himself but has access only to a scale A with capacity…

A:

Q: Abbot and Costello are transporting a 0.125m3 cubic block along a ramp inclined at 20°. They tied…

A: Given: Volume of cube is 0.125 m3. Mass of the pole arm is 2 kg.  Length of the pole arm is 3 m.…

Q: the force (in kN) in the member SR is

A: Given; Figure shows the truss, where,  the load and the length of the bar is shownDetermine the…

Q: force of P=180lb supports a 300lb box in an inclined plane as shown. Determine the angle at which it…

A: Given: To determine the angle of slope for the box to remain in equillibrium. P=180 lb W=300 lb

Q: Q2/ A former student of mechanics wishes to weigh himself but has access only to a scale A with…

A:

Q: The unstretched length of spring AB is 1 m. If the block is held in the eguilibrium position shown,…

A: Expression for length of AB;

Q: Calculate the tension in each cable in kilo-Newtons.

A:

Q: .15 An inclined cable is used to pull on a log as shown. Determine the magnitude of the force…

A: Assuming the surface on which the log is kept as frictionless and the log itself being massless.

Q: Calculate the force in each cable for the suspended weight shown.

A:

Q: if the weight is 2g give the force-1

A: Given     Weight, w = 2 g

Q: find the weight of the wooden beam shelf attach on the wall.

A:

Q: A bodybuilder holds a dumbbell of weight Wd. His arm is horizontal and weighs 41 N. The deltoid…

A:

Q: Compute for the forces P and Q if the force in member CD is equal to 6000 lb (C) and in member GD is…

A:

Q: nd the weight of the lightest block D that can be used to support the 100 kg uniform pole ABC in the…

A: GIVEN: mass of pole ABC, m1=100 kg

Q: A gardener uses a 60-N wheelbarrow to transport a 250-N bag of fertilizer. What force must she exert…

A:

Q: Q5-the crate has weight of 550 lb.determine the force in each supporting cable?

A:

Q: Draw FBD at point A and determine the force developed in each cable used to support the 40kN crate…

A:

Q: Determine the greatest force F that can be applied to the ring if each cable can support a maximum…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.