Question 2 Give a bar subjected to the concentrated forces and uniformly distributed force within segment CD as shown in Figure 2. The cross- sectional area of the bar is 6 cm². 1. Draw the normal force diagrams of the bar 2. Draw the diagram of normal stresses of the bar 1.1 m 3.9 m 2.4 m A B 20 KN 40 kN C 12kN/m D ✓110 KN Figure 2

Question 2 Give a bar subjected to the concentrated forces and uniformly distributed force within segment CD as shown in Figure 2. The cross- sectional area of the bar is 6 cm². 1. Draw the normal force diagrams of the bar 2. Draw the diagram of normal stresses of the bar 1.1 m 3.9 m 2.4 m A B 20 KN 40 kN C 12kN/m D ✓110 KN Figure 2

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.8P: An element in plane stress on the fuselage of an airplane (figure part a) is subjected to...

See similar textbooks

Similar questions

-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
At a point on the surface of an elliptical exercise machine, the material is in biaxial stress with t = 1400 psi and trv = —900 psi, as shown in the figure part a. The figure part b shows an inclined plane aa cut through the same point in the material but oriented at an angle ft Determine the value of the angle 6 between zero and 90° such that no normal stress acts on plane aa. Sketch a stress clement having plane aa as one of its sides and show all stresses acting on the clement
The polyethylene liner of a settling pond is subjected to stresses ax= 350 psi. a = 112 psi. and = -120 psi, as shown by the plalte-stress element in the figure part a. Determine the normal and shear stresses acting on a seam oriented at an angle 01300 to the element, as shown in the figure part b. Show these stresses on a sketch of an element having its sides parallel and perpendicular to the seam.
.4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the stresses on an inclined section through the element at an angle ? = 45°.
Solve the preceding problem for an element in plane stress on the bottom surface of a fuel tanker (figure part a); stresses are sx= 105 MPa, sy. = 75 MPa, and ??xy= 25 MPa. Determine the stresses acting on an element oriented at an angle ?? = 40° from the x axis, where the angle is positive when counterclockwise. Show these stresses on a sketch of an element oriented at the angle ??.
An element in plane stress on the fuselage of an airplane (figure part a) is subjected to compressive stresses with a magnitude of 42 MPa in the horizontal direction and tensile stresses with a magnitude of 9.5 MPa in the vertical direction (sec figure part b). Also, shear stresses with a magnitude of 15.5 MPa act in the directions shown. Determine the stresses acting on an element oriented at a clockwise angle of 40g from the horizontal. Show these stresses on a sketch of an element oriented at this angle.
The stresses on an element are sx= 1000 Psi. sy= 500 psi, and txy= 350 psi. Find the stresses acting on an element oriented at an angle 0 = 250. Show these stresses on the rotated element.
A spherical balloon with an outer diameter of 500 mm and thickness 0.3 mm is filled with a gas. Calculate maximum permissible pressure in the balloon if the allowable normal strain at the outer surface of the balloon is O.h Assume E = 4 MPa and v = 0,45.
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
Two solid cylindrical rods support a load of P = 39 kN, as shown. Rod (1) has a diameter of 16 mm and the diameter of rod (2) is 11 mm. Determine the axial stress in rod 2. Assume a = 2.2 m, b = 4.6 m, c = 2.7 m, and d = 2.4 m. Use positive for tensile stress and negative for compressive stress. Express your answer in MPa rounded to the nearest whole number.
Two solid cylindrical rods support a load of P = 39 kN, as shown. Rod (1) has a diameter of 16 mm and the diameter of rod (2) is 11 mm. Determine the axial stress in rod 1 and rod 2. Assume a = 2.2 m, b = 4.6 m, c = 2.7 m, and d = 2.4 m. Use positive for tensile stress and negative for compressive stress. Express your answer in MPa rounded to the nearest whole number.