Question 2: Joints A, B, C, D, and E are frictionless pins. Fand G are rough surface contacts. (a) Identify any 2 force members. (b) Complete the FBDS of all parts with all arrows in the correct direction and labelled (you do not need to draw a FBD of the cable at E). - 18"- 18 12 20 800 lb 24 30

Question 2: Joints A, B, C, D, and E are frictionless pins. Fand G are rough surface contacts. (a) Identify any 2 force members. (b) Complete the FBDS of all parts with all arrows in the correct direction and labelled (you do not need to draw a FBD of the cable at E). - 18"- 18 12 20 800 lb 24 30

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

If the 18 mm plate is connected to two cover plate of 10 mm on top and bottom, what is the capacity of the connection in double shear? Assume that the shear planes pass though the threaded portion. State the condition necessary for these strengths to be available. (Draw the connect first and calculate the capacity)
A flange bolt coupling has ten steel 25.4 mm diameter bolts evenly tighten around a 415 mm bolt circle. Determine the torque capacity of the connection if the allowable shearing stress in the bolt is 50 MN/m2 . A. 59.95 kN - m B. 52.6 kN - m C. 46.15 kN - m D. 43.8 kN – m
A dead load of 3 kips and a live load of 9 kips make up the load at each of the points A, C, D, and E in the truss shown below. A dead load of 6 kips and a live load of 18 kips make up the load at point B. The whole panel points function as pinned connections and Fy = 36 ksi. The gross cross-sectional area of steel required for member A-H is most nearly: (A) 1.5 in2 (B) 1.8 in2 (C) 2.0 in2 (D) 2.3 in2 Choose the correct answer.
Pins B and C experience the same force, and are both used in a double shear connection. Consider pin B. Use the ultimate shear strength, the factor of safety, and the force at B to calculate the minimum required diameter for pins B and C. dpin B,C= ? (unit mm)
Check the block shear capacity of the connection, use lrfd and asd design expression. Given the lightest W section from Plate 3, connected toa PL% x 10 on its top and bottom flanges, available to support working tensile loads of D = 420 kips and W = 330 kips. The member is to be 20 ft long and is assumed to have two lines of holes for 4-in diameter bolts in each flange. There will be at least three holes in each line 3 inches on center.
The crate has an unknown weight W and is held by cable AB, AC, and AD. Each cable can hold a max of 450 pounds. There are the following coordinates: A(0,0,0) B(-2,1,2) C(-2,-2,1) D(3,0,0). Part A) Find the max weight W that the system can hold without breaking any cables Part B) Use the weight from part A to find the tension in the cables draw all FBDs please
Simply Supported Beam ABCDE below carries multiple loads as shown. A built-upsection made from a T-Section and a Channel (C-Section) fastened together by 16mm∅ bolts,equally spaced from the center of the section, with shearing capacity τ=100 MPa, for bearing σb= 220 MPa for rivets in single shear and σb = 280 MPa for rivets in double shear. E=200GPa forall materials. 4. Determine the location of the centroid, in mm, from the left of the section.5. Determine the moment of inertia of the section in x106mm4.6. Determine the moment capacity of the section, kN-m, if fbcap≤300 MPa.
Block 4 slides in the slot in the fixed piece 1. Axis Q2 of crank 2 is fixed on 1. Q2A = 1 1/2 in, and AB = 4 1/2 in. Draw the mechanism assuming dimensions for 1, if desired, or use center lines only. Draw four-bar linkage for this mechanism, properly notate the linkage Q2 ABQ4∞, name each link and show finite and infinite cranks
The gate shown is hinged through a point A and is restrained from opening by a fixed ridge at point B. For a gate width of 2 meters, •Determine the magnitude and direction of the force exerted on the plate by the ridge. Illustrate and label the FBD of the force system. Express your answer in kN. DRAW FBD. NEED IT ASAP!
A steel plate of dimensions 2.5 X1.5 X 0.08 mand weighing 23.1 kN is hoisted by steel cables withlengths L1 = 3.2 m and L2 = 3.9 m that are eachattached to the plate by a clevis and pin (see figure).The pins through the clevises are 18 mm in diameterand are located 2.0 m apart. The orientation anglesare measured to be θ = 94.4° and α = 54.9°.For these conditions, first determine the cableforces T1 and T2, then find the average shear stressτaver in both pin 1 and pin 2, and then the averagebearing stress σb between the steel plate and each pin.Ignore the weight of the cables.
Problem 12. A plate is used as a bracket and is attached to a column flange as shown in the figure. The loads are factored loads. The eccentricity of the load is a x = 30 mm; y = 75 mm b x = 45 mm; y = 100 mm c x = 150 mm; y = 250 mm d x = 180 mm; y = 125 mm 13. For the connection shown in problem, the resisting moment of the bolts is a 18 kN - m b 20.915 kN - m c 29.25 kN - m d 36 kN - m 14. For the connection shown in problem 12, using elastic analysis the force on the most stressed bolt is a 21.451 kN b 57.051 kN c 91.415 kN d 180 kN 15. For the connection shown in problem 12, the critical bolt is the bolt located at a upper left b upper right c lower left d lower right 16. For the connection shown in problem, determine the diameter of the bolts if A325X bolts are used. a M16 bolts b M20…
The figure shows a truss and the detail of the riveted connection at joint H. Using allowable stresses ofτ = H MPa and σb= I MPa, how many 19-mm diameter rivets are required to fasten member HB to thegusset plate? Member HC? Round-up your answer to a whole number F=162 H=110 I= 180