PLEASE ANSWER IT ALL ASAP FOR AN UPVOTE. THANKYOU. A 0.9 meter radius circular footing is embedded 1.07 meters beneath the ground surface. The groundwater table is located 1.51 meters from the ground surface. The soil report also indicates a homogeneous soil profile with cohesion = 19 kPa, moist unit weight = 17.63 kN/m3, and submerged unit weight = 10.83 What is the gross ultimate bearing capacity (kPa) of the footing?

Q: xample of unsteady flow problem

A: If properties of flow changes with time at a given space then such a flow is called unsteady flow. F...

Q: The sum of forces in the member BC and GH in the following pin jointed frame is kN. Take compression...

A:

Q: A rectangular channel 2.5 m wide carries water at a depth of 1.2 m. The bed slope of the channel is ...

A:

Q: A vertical curve with a length of 260 m is used to c elevation 1035.3 m. The location of the highest...

A: G1 = 2.5 % G2 = - 2.5 % A = G1 - G2 A = 2.5+2.5 A = 5 PVC elevation = 1035.3m L = 260 m

Q: Spot speed study has been carried out on a highway and collected data is shown in the table below. S...

A: Given data,

Q: vertical, cylindrical tank, 5 ft in diameter and 12 ft high, is held together by means of two steel ...

A:

Q: The two cylinders shown are identical and weighs 1000 N. The inclined smooth surface is 33° from the...

A:

Q: Design the vertical stem of a T-shaped retaining wall for a height of 3 m above the ground level. Th...

A:

Q: Two loads of 15 kN and 32 kN (leading) spaced 6 m apart moving left to right on an over hanging beam...

A: Given data, Two loads of 15 kN and  32 kN spaced 6 m

Q: The base length of the runway at The mean sea level (MSL) is 1500 m. If the runway is located at an ...

A:

Q: for soils A and B are as follows:  NOTE: PI=5% for Soil A (Solution are required)   a.) Determine th...

A: USCS soil clsssification:iLook at the % passing through sieve no 200=70>50%⇒FINE GRAINED SOILiiLi...

Q: he angular acceleration of the horizontal bar BD and (b) the ang 6V3 in 30

A:

Q: 1. The beam is subjected to a load F = 400 N and is supported by the rope and the smooth surfaces at...

A: To Determine a. Draw the free-body diagram of the beam. b. What are the magnitudes of the reactions ...

Q: The weight of a dry aggregate sample is 1300 gms, and it is desired to prepare a specimen of asphalt...

A:

Q: maximum stresses in the steel pipe and the plastic sleeve,

A: Given: Inner diameter of the pipe = 10 in. Wall thickness = tp=0.375 in. Thickness of Plastic sleeve...

Q: elevation 1035.3 m. The location of the highest point on this curve in m from PVC is about The eleva...

A: L=260m G1=2.5% G2=-2.5%

Q: Find the maximum uniçormly distributed Ibad (1w) the beam can carry stress are iF the allowable bend...

A: Given  Allowable bending stress= 60 Mpa  Shearing stress= 60 Mpa 

Q: Compute the capitalized cost of a new car worth P800,000 if it is estimated that is requires P20,000...

A: The capitalized cost of the car or equipment is defined as the total cost incurred by the company ov...

Q: beam has a uniform dead load and live load has a fixed support at both ends. If the beam properties ...

A:

Q: Structural Design assignment In a preliminary design, a typical floor of a multi-story building is o...

A: Estimation: Estimation is the process of estimation and computation of the different materials requi...

Q: Problem 2 For the cross-section shown below, Mz = 150 kN.m and My = 250 kN.m. Determine the maximum ...

A:

Q: In a flownet diagram, the length of the flow line in the last square is 2 m the total head loss is 1...

A:

Q: A rectangular channel 2.5 m wide carries water at a depth of 1.2 m. The bed slope of the channel is ...

A:

Q: Compute øV½ for the cross-section shown. Use f'c = 4000 psi and fyt = 60 ksi. 16" 28" #3 3 #9 stirru...

A: Given: The value of f’c is 4000 psi. The value of fy is 60 ksi. Consider the figure,

Q: For the joint shown in the figure, calculate (a) the largest bearing stress between the pin and the ...

A: Given data: Load on the member is 25 KN

Q: Problem 2 Find the loading for the floor beams B-1 through B-5, and G-3 through G-5 of Problem 2 of ...

A: A floor beam is a huge pillar, normally steel, that traverses the width of a house at the middle and...

Q: 1.) The most accurate source of data is national standards books. true or false 2.) The geometric ...

A: 1) if we consider the Engineering data, then the national standard books like national standard book...

Q: 10 in 11 in 10 in A 20 kips 35 kips 81 kips This s nor your cwn phoperty so do rat ue in any way as ...

A:

Q: 120 kN 120 kN B C -5 m -3 m L=15 m El = constant E = 30 GPa The beam has a self weight of 5 kN/m in ...

A: Given : Simply supported beam with self weight 5 kN/m acting on it E = 30 * 10^3 N/mm2 I = 1800 * 10...

Q: .What is the acceleration of an object which accelerates along a straight path from rest, and attain...

A: Given data : Initial velocity=U U=0 m/s Final velocity=V V=20 m/s Time=t t=5 s Distance =S S=50 m

Q: m. FOT Uone he location of the highest point on this curve in m from The elevation of PVT on this cu...

A:

Q: Four cards are drawn together from a deck of 52 cards. Find the probability that all are face cards....

A:

Q: Find the value of EI0 at the free end of the cantilever beam.

A:

Q: 1-56.M A short compression member has the cross section shown in Figure Pl-56. Compute the stress in...

A:

Q: A B 8.80m 8.20m 10.80m (1) 8.10m 2 Q 10m

A:

Q: A vertical curve with a length of 260 m is used to connect a 2.5 % and-2.5% gradients with a PVC at ...

A: Given - The Length of vertical curve = 260m Gradient G1 = 2.5% G2 = -2.5% Elevation at PVC = 1035.3m...

Q: A flanged-bolt coupling consisting of six % inch diameter steel bolts evenly spaced around a bolt ci...

A:

Q: an elevated tank is used to supply water to a building located 4800 ft away. the water will be carri...

A:

Q: fineness modulus

A: To determine the fineness modulus for the given sample Given: 3/8 in 4 8 16 30 50 100...

Q: A 1000 MW power plant is operating at 38% efficiency. The ash and sulphur content in the coal used a...

A:

Q: A group of 4 point loads 3000 kN each are acting on the vertices of a rectangular area of length 5 m...

A:

Q: Given the existing components of each reaction with load P = 100 N. Determine the following: a.) The...

A:

Q: 1. A 2 hr. UH is shown below Time (hr.) Discharge (m³/sec.) 1 2 15 3 12 4 10 5 If a storm of 4.2 cm....

A: Given 2hr UH  Effective rainfall is equal to total rainfall - loss.  

Q: How much mass of cement required if the volume of cement need to create 1.0 m3 of concrete is 0.135 ...

A:

Q: A built-up beam made from fastening two channels to a wide flange section carries loads` as shown. T...

A:

Q: Two trains travel on parallel tracks in the same direction. The first train has a length of 100m and...

A:

Q: aw the NFD, SFD, BMD for the following beams: 50 kN 10 kN/ m 3m 4 m

A:

Q: 16KN 30 KN/m А D 2.4 3.2 1.8

A:

Q: Can you tell the mechanism behind palm beach bridge? Like how do the bridge move up, I want to desig...

A: Bridge engineering is a field of civil engineering that focuses on the planning, design, building, o...

Q: at the building site. what should be the height of the water tank above the invert of the building t...

A:

Load and resistance factor design

Load and resistance factors design (LRFD), also known as Limit state design (LSD), refers to the design method used in building engineering. A boundary condition is a condition of a structure where it can no longer meet the relevant design requirements. The condition may refer to the load level or other actions on the structure, while the terms refer to the integrity of the structure, suitability for use, durability, or other design requirements. A structure designed for LRFD is limited to keeping track of all possible actions during its design time and is always ready for use, with the appropriate level of reliability in each boundary condition. LRFD-based construction codes clearly define the appropriate levels of reliability in their instructions.