Question-2 The circular gate ABC has a Im radius and is hinged at B. Compute the force P just sufficient to keep the gate from opening when (h 8 m). Neglect atmospheric pressure. ( = 9790 kN) Water P. Im Im

Question-2 The circular gate ABC has a Im radius and is hinged at B. Compute the force P just sufficient to keep the gate from opening when (h 8 m). Neglect atmospheric pressure. ( = 9790 kN) Water P. Im Im

Name: keep the gate from opening whenThe circular gate ABC has a Im radius
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: keep the gate from opening whenThe circular gate ABC has a Im radius and is hinged at B. Compute the force P just sufficient toQuestion-2(h 8 m). Neglect atmospheric pressure.%3DPa7- = 9790 kmWaterP.ImIm

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.119P: Determine the force F required to pull up the 3.54m stopper from the drain of a sink if the depth of...

See similar textbooks

Similar questions

The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate and the smooth surface at B due to water pressure acting on the gate. Use =62.4lb/ft3 for water.
The weight of the cylindrical tank is negligible in comparison to the weight of water it contains (water weighs 62.4lb/ft3). The coefficient of static friction between the tank and the horizontal surface is s. (a) Assuming a full tank, find the smallest force P required to tip the tank, and the smallest s that would allow tipping to take place. (b) If the force P = 200 lb initiates tipping, determine the depth of water in the tank.
Determine the force F required to pull up the 3.54m stopper from the drain of a sink if the depth of water is 10 in. Use =0.036lb/in.3 for water and neglect the weight of the chain.
The high-pressure water cock is rigidly attached to the support at D. Neglecting the weights of the members, draw the FBD of the entire assembly and count the unknowns.
Q 244 What are the reaction forces on the latch an djoint in the gate below? And in case thefloodgate is reversed (concave)? *The gate is a cylinder room with length L = 5 m
Find a) the total force on gate AB in KN and b) the position of the center of pressure in m with respect to the bottom of the pond. Assume that the gate is 8 feet wide, that 1ft = 0.3048m, and that 1PSI = 6897.1 Pa
What are the reaction forces on the latch an djoint in the gate below? And in case thefloodgate is reversed (concave)? *The gate is a cylinder room with length L = 5 m
Gate AB is 1.5 m wide into the paper and opens to let fresh water out when the ocean tide is dropping as shown in the Figure Q1. The hinge at A is 0.6 m above the freshwater level. Determine the minimum force at B on the seawater side when the gate first open if h = 2.95 m. Neglect the weight of the gate.
The strength per meter of the longitudinal joint in the figure is 480 kN, whereas or the girth joint is 200 kN. Determine the maximum diameter of the cylindrical tank if the internal pressure is 1.5 MPa.
Find a) the total force on gate AB in KN and b) the position of the center of pressure in m with respect to the bottom of the pond. Assume that the gate is 8 feet wide, that 1ft = 0.3048m, and that 1 psi = 6897.1 Pa. Relative density salt water 1.025.
Show the derivation of the girth and longitudinalstresses of the thin-walled cylindrical container shownbelow. Say p is the internal pressure, d is the insidediameter of the container, and t is wall thickness.
Your answer is partially correct. A homogeneous, 4-ft-wide, 9.8 -ft-long rectangular gate weighing800lbis held in place by a horizontal flexible cable as shown in the figure below. Water acts against the gate, which is hinged at point A. Friction in the hinge is negligible, Determine the tension in the cable. AssumeL1=9.8ft,L2=7.2ft, andθ=57∘. Please type answer note write by hend.