Question 2 The permissible shear stress for the weldment in the figure below is 171 MPa. Estimate the angle that the secondary shear stress acts. Take F = 75 kN and a = 106 mm. Give your answer in degrees. Do not include the unit when submitting and work to 3 decimal places. ᏂᏤ h a 180 mm 150 mm

Question 2 The permissible shear stress for the weldment in the figure below is 171 MPa. Estimate the angle that the secondary shear stress acts. Take F = 75 kN and a = 106 mm. Give your answer in degrees. Do not include the unit when submitting and work to 3 decimal places. ᏂᏤ h a 180 mm 150 mm

Essentials of Business Analytics (MindTap Course List)

2nd Edition

ISBN:9781305627734

Author:Jeffrey D. Camm, James J. Cochran, Michael J. Fry, Jeffrey W. Ohlmann, David R. Anderson

Publisher:Jeffrey D. Camm, James J. Cochran, Michael J. Fry, Jeffrey W. Ohlmann, David R. Anderson

Chapter5: Probability: An Introduction To Modeling Uncertainty

Section: Chapter Questions

Problem 33P: Suppose that Motorola uses the normal distribution to determine the probability of defects and the...

See similar textbooks

Similar questions

Calculate the material loading percentage (ROUND ANSWER TO 3 DECIMAL PLACE)
Part C: a) Apart from the basic costs to build up a unit rate, explain FIVE other factors you will consider in adjusting a reference unit rate to a new unit rate.
Question – 2 (remaining part)T he following information was taken from the books of MEHRAN MANUFACTURING CO.: STANDARD ACTUALMaterial 5,000 kg @ Rs. 10 4,800 kg @ 10Labour 1,000 Hours @ Rs. 18 1,200 Hours @ 16Factory Overhead Rs. 3,000 Rs. 3,600Required: (remaining part) 2] Prepare the Journal Entries to record and close above variances. 1] Compute the Following: a) Material Price Varianceb) Material Quantity Variance c) Labour Rate Varianced) Labour efficiency variance e) Overhead Variance
1. The highest Contribution Margin is: 2. The highest Contribution Margin Ratio is: Note: Enter up to three decimals. For example, for 36.28^% enter 0.363. 3. Which margin is most useful in evaluating segment viability?a) Contribution margin’b) None of the abovec) Controllable contribution margind) Segment Margin
Hi, I need help imputting the following values. Thank you. NOTES: #1: (Round answer to 2 decimal places.) #2: (Round "predetermined overhead rate" to 2 decimal places. Round other calculations and final answer to the nearest whole dollar.) #3 and #4: (Round intermediate calculations to the nearest whole number and final answer to 2 decimal places.)
Suppose that Motorola uses the normal distribution to determine the probability of defects and the number of defects in a particular production process. Assume that the production process manufactures items with a mean weight of 10 ounces. Calculate the probability of a defect and the suspected number of defects for a 1,000-unit production run in the following situations. a. The process standard deviation is 0.15, and the process control is set at plus or minus one standard deviation. Units with weights less than 9.85 or greater than 10.15 ounces will be classified as defects. b. Through process design improvements, the process standard deviation can be reduced to 0.05. Assume that the process control remains the same, with weights less than 9.85 or greater than 10.15 ounces being classified as defects. c. What is the advantage of reducing process variation, thereby causing process control limits to be at a greater number of standard deviations from the mean?
Question – 2T he following information was taken from the books of MEHRAN MANUFACTURING CO.: STANDARD ACTUALMaterial 5,000 kg @ Rs. 10 4,800 kg @ 10Labour 1,000 Hours @ Rs. 18 1,200 Hours @ 16Factory Overhead Rs. 3,000 Rs. 3,600Required: 1] Compute the Following: a) Material Price Varianceb) Material Quantity Variance c) Labour Rate Varianced) Labour efficiency variance e) Overhead Variance2] Prepare the Journal Entries to record and close above variances.
What is the cost, c, of a call of m minutes duration? Write the equation in both point-slope and slope-intercept form.
Question # 1 Standard and the actual costs for direct materials and direct labor are given as under: Standard costs Direct materials 8,000 units at total direct material costs Rs. 40,000 Direct labor: 7,000 hours at Rs. 6 per hour Actual costs Direct materials 8,500 units at Rs. 4.5 per unit Direct labor: 6,500 hours at Rs. 6.25 per hour Required Material Price Variance and Material Quantity Variance Labor Rate Variance and Labor Efficiency Variance Entries in general journal to record the above information What do you realize whether the overall variation is in favorable or unfavorable?
Compute for the variances of the problem using the information given. Answer the numbers only up to two decimal places. A. Compute for Direct Materials Spending Variance B. Compute for Direct Materials Price Variance C. Compute for Direct Materials Quantity Variance
Question # 1 Standard and the actual costs for direct materials and direct labor are given as under: Standard costs Direct materials 8,000 units at total direct material costs Rs. 40,000 Direct labor: 7,000 hours at Rs. 6 per hour Actual costs Direct materials 8,500 units at Rs. 4.5 per unit Direct labor: 6,500 hours at Rs. 6.25 per hour Required a. Material Price Variance and Material Quantity Variance b. Labor Rate Variance and Labor Efficiency Variance
Yau are the project munager for a technical implementstion project. The customer has requested that you factor in the after-the-project costs such as maintenance and sence. This is in example of which one of the following. A. Life griecosts B. Scope creep C Propect spin olf 0, Operations