Please, I need the final solution as soon as possible, I do not need any explanation or explanation QUESTION 21In the Wireless LAN shown in the figure below, Host1 is connected to a website in theInternet. This connection happened because Host1's BSS is connected to:Host1000000000BSAooooooBSSID00d0:bc80.dd07Extended Service Area (ESA)ooooooPC devices in the ESSmore than one BSS.This connection is not possible because Host1 is in an ESS.Distributed SystemDistributionSystemFigure: IEEE 802.11 ESS Wireless LANpooooooBSABSSID00d0afdb.e0fc

SOLUTION ANSWER Distributed System

QUESTION 21 In the Wireless LAN shown in the figure below, Host1 is connected to a website in the Internet. This connection happened because Host1's BSS is connected to: OO Host1 BSA oooooo BSSID 00d0:bc80.dd07 Extended Service Area (ESA) 000000 PC devices in the ESS more than one BSS. This connection is not possible because Host1 is in an ESS. Distributed System Distribution System Figure: IEEE 802.11 ESS Wireless LAN poooooo BSA BSSID 00d0afdb.e0fc

QUESTION 21 In the Wireless LAN shown in the figure below, Host1 is connected to a website in the Internet. This connection happened because Host1's BSS is connected to: OO Host1 BSA oooooo BSSID 00d0:bc80.dd07 Extended Service Area (ESA) 000000 PC devices in the ESS more than one BSS. This connection is not possible because Host1 is in an ESS. Distributed System Distribution System Figure: IEEE 802.11 ESS Wireless LAN poooooo BSA BSSID 00d0afdb.e0fc

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter27: Service-entrance Equipment

Section: Chapter Questions

Problem 7R: a. What size and type of conductors are installed for the service in this text? _____________ b....

See similar textbooks

Similar questions

this question belongs to communication systems and networks.. if you could shift it to the right gentleman..thanks
Calculate the voltage drop of a 120/240 volts, three wire underground residential service installed with 2 AWG aluminum URD cable if the load is 80 amps and the one way length of the underground service conductor is 100 feet.
Please answer both questions in short for like this please Asap for like this please
Briefly explain TNC-S earthing scheme as applied to earthing system design. (Hint: Support your answer with a well labelled diagram).
The following problems refer to grounding requirements. Give the source of yourresponses. 1. What is the minimum size copper grounding electrode conductor for a service withthree sets of parallel 350 kcmil conductors (three conductors per phase)?
Please answer ASAP for like Please Asap Please
The block diagram in the figure shows the root locus of the system. draw?
Please answer ASAP for like.. Please Asap..
10.a. Which of the following is a condition of the exception that allows the grounded conductor of feeders tobe used for grounding at separate buildings or structures?A. There are common electrically continuous metallic paths between the feeder source and the destination at the structure served.B. There are common electrically continuous nonmetallic paths between the equipment grounding conductor and the destinationat the structure served.C. An equipment grounding conductor isn't included with the supply circuit to the separate structure.D. Ground-fault protection of equipment is provided on the supply side of the feeder.10.b. A service disconnection means must be installed adjacent to, within sight of, and no more than_______ feet from a mobile home.A. 20B. 30C. 10D. 50
What is the effect of the blue wire on the circuit?https://www.bartleby.com/questions-and-answers/use-the-tinkercad-breadboard-to-showdraw-this-circuit./ee2909ad-395a-48ad-b691-f9169ded5b4e
Please answer ASAP for like Please answer
6.a. What type of cable installation is typically used in industrial facilities?A. Aerial onlyB. Buried onlyC. Buried and aerialD. Industrial facilities don't use cable installations.6.b. Which type of fiber is used in a standard FDDI network?A. OM3 or OM4 at 850 nmB. OM1 at 1,550 nmC. OM2 at 1,310 nmD. OM1 at 1,310 nm