Question 3 A set of weight measurements and their expected values are given below, Expected Weight We (kg) Measured Weight Wm (kg) 6.0 7.0 8.0 9.0 10.0 11.0 5.9 6.8 7.7 8.8 9.9 10.9 If the weighing machine has a full-scale deflection of 15 kg, (a) calculate the absolute, relative and full-scale errors for each of the measurements. You should use a table to present your results. (b) Give a possible reason why the measured weights are consistently lower than the expected values.

Question 3 A set of weight measurements and their expected values are given below, Expected Weight We (kg) Measured Weight Wm (kg) 6.0 7.0 8.0 9.0 10.0 11.0 5.9 6.8 7.7 8.8 9.9 10.9 If the weighing machine has a full-scale deflection of 15 kg, (a) calculate the absolute, relative and full-scale errors for each of the measurements. You should use a table to present your results. (b) Give a possible reason why the measured weights are consistently lower than the expected values.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the diameter for a of a small metal sphere using a Micrometer for the following measurement trial, then Calculate the absolute (∆V), relative (δV), and the percentage (%V) errors in the volume of the sphere given that
The length of a iron bar is measured by a number of different observers and the following set of 12measurements are recorded (units mm)302,304,303,305,307,309,310,311,312,301,303,302. Find the values of mean, median, variance andstandard deviation.
A manufacturer claims that the average tensile strength of thread A exceeds the average tensile strength of thread B by at least 12 kilograms. To test this claim, 50 pieces of each type of thread were tested under similar conditions. Type A thread had an average tensile strength of 86.7 kilograms with a standard deviation of 6.28 kilograms, while type B thread had an average tensile strength of 77.8 kilograms with a standard deviation of 5.61 kilograms. Test the manufacturer’s claim using a 0.05 level of significance. 1. Determine the Z calculated in two decimal places. 2. Determine the Z table in two decimal places. 3. Is the manufacturing claim statistically valid? yes or no
The record of highest temperature in eight specific states is given below. 112, 100, 127, 120, 134, 118, 105, and 110. Find the values of mean, median, variance, standard deviation and Probable error.
1.Calculate Mean ,Median ,standard deviation and variance for measurement sets A, B and C SET A :398 ,420, 394, 416, 404, 408 ,400, 420 ,396, 413 ,430. • SET B:409 406 402 407 405 404 407 404 407 407 408 SET C:409 406 402 407 405 404 407 404 407 407 408 406 410 406 405 408 406 409 406 405 409 406 407
Ten measurements are taken resulting in a standard deviation of 0.10 s.a. Determine the uncertainty in the measurement.b. If an uncertainty one fifth the value found in a. is desired how many measurementswould be required (assume that the standard deviation with this number ofmeasurements is the same as with ten measurements).
Measurement in Engineering Question is image C) ? c) Determine a 95% confidence interval for Nu and report the value.
8.. An air blower is to deliver 40,000 ft3 /min. Two U-tube gages measure suction and discharge pressures. The suction gage reads a negative 2′′ of water. The discharge gage, located 3 ft above the point to which the suction gage is attached, reads +3′′ of water. The discharge and suction ducts are of equal diameter. What size motor should be used to drive the blower if the overall efficiency is 68% (γ = 0.0750 lb/ft3 for air)? indicate free body diagram
Bearing used in an automotive application has a nominal inside diameter of 3.81 is expected to be cm.A random sample of 25 bearings is selected andaverage inner diameter of bearing3.8037 cm. exists as. bearing inner diameter σ=0.03 cm Standard deviation ofis known to be normally distributed. α=0.01 ; a) Test whether the bearing used has a nominal inside diameter of 3.81 cm. b) How to answer the question in part (a) by constructing a two-sided confidence interval on the mean diameter?explain that you can answer note: can you write the solutions legibly.
Pressure distribution measurements are made on a two-dimensional wing model placed in a wind tunnel. The difference between the static pressure sockets on the surface and the static pressure of the free stream is measured. 30 data is taken at each measurement point. The average of the values measured from one of the sockets near the trailing edge was calculated as 2.30 Pa, and the standard deviation was calculated as 2.65 Pa. After applying the Chauvenet criterion to these measurement values, it was decided to eliminate 3 measurements and the new mean value was found to be 2.18 Pa and the standard deviation was 2.42. It was verified that the unexcluded data fit the normal distribution curve. Data above how many Pa and below how many Pa were eliminated? Estimate how many data have negative value (?<0) after elimination.
Kindly provide a detailed and factual solution so I can study. And the final answer should be rounded off up to four decimal places. Use the parameters given.
A tape 30m long of standard length a 29Celcius was used to measure a line the mean temperature during measurement was 15Celcius, the measured distance was 221.65 m, the following being the slopes:1 degree 10’ for 60 m2 degree 20’ for 30 m5 degree 18’ for 30 m4 degree 40’ for 12 m1 degree 30’ for 30 m3 degree 48’ for 30 m7 degree 20’ for 18 m1 degree 20’ for 11.65 mFind the true length of the line if the coefficient of expansion is 116x10^-7 per 1Celcius