Question 3 a. A freight-car axle AB is loaded approximately as shown in figure 3a, with the forces P representing the carloads (transmitted to the axle through the axle boxes) and the forces R representing the rail loads (transmitted to the axle through the wheels). The diameter of the axle is, the distance between the centers of the rails is L, and the distance between the forces P and R is. Calculate the maximum bending stress amax in the axle if. d = 82 mm b = 220 mm P = 50 kN. $ Pl 17 R b Figure 3a. Freight car axle ||

Question 3 a. A freight-car axle AB is loaded approximately as shown in figure 3a, with the forces P representing the carloads (transmitted to the axle through the axle boxes) and the forces R representing the rail loads (transmitted to the axle through the wheels). The diameter of the axle is, the distance between the centers of the rails is L, and the distance between the forces P and R is. Calculate the maximum bending stress amax in the axle if. d = 82 mm b = 220 mm P = 50 kN. $ Pl 17 R b Figure 3a. Freight car axle ||

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Draw the Shear Force and Bending Moment Diagram for the loaded simply supported beam shown below. Ignore the self-weight of the beam
For the beam shown below, the distributed load along AB is a= 6 kN/m, the concentrated load at Point C is b = 10 kN. Draw FBD, sove for reaction forces, then draw shear & momment diagram. Input the internal bending moment at the cross-section from Point B: ____ kN m. Input the negative sign "-" if it is negative, and calculate your answer to 1 decimal place.
For the beam shown in the figure below: Part A.) Calculate the reactions at the supports. Part B.) Draw the shear force diagram and bending moment diagram, showing values at points A, B, C, and D. Part C.) Determine the value and location of the maximum positive and negative bending moment acting on the beam.
A timber dam is made of planking backed by vertical piles. The piles are built-in at the section A where they enter the ground and they are supported by horizontal struts whose center lines are 10 m above A. The piles are spaced 1 m apart between centers and the depth of water against the dam is 10 m. Assuming that the thrust in the strut is two-sevenths the total water pressure resisted by each pile, sketch the form of the bending moment and shearing force diagrams for a pile. Determine the magnitude of the bending moment at A and the position of the section which is free from bending moment. (Cambridge). i. 238 kN-m; 0.75 m from A. ii. 238 kN-m; 0.75 m from B.
The cantilever beam in Fig. (a) carries a triangular load, the intensity of which varies from zero at the left end to 360 lb/ft at the right end. In addition, a 1000-lb upward vertical load acts at the free end of the beam. (1) Derive the shear force and bending moment equations, and (2) draw the shear force and bending moment diagrams. Neglect the weight of the beam
A flanged wooden shape is used to support the loads shown on the beam in Figure (a). The dimensions of theshape are shown in Figure (b). Consider the entire 18 ft length of the beam and determine:(a) the maximum tensile bending stress at any location along the beam, and
For the figure shown below, compute the bending moment in section 1. Neglect the weights of the member. Note that point B is pin-connected.
Calculate the normal stress, shear stress, and bending deformation of the beam. (Point A has a pinned support, while point C has a roller support)
A freight-car axle AB is loaded approximatelyas shown in the figure, with the forces P representingthe car loads (transmitted to the axle through the axle boxes) and the forces R representing the railloads (transmitted to the axle through the wheels).The diameter of the axle is d = 82 mm, the distancebetween centers of the rails is L, and the distancebetween the forces P and R is b = 220 mm.Calculate the maximum bending stress σmax inthe axle if P = 50 kN.
When a beam has only uniformly distributed forces applied, the moment diagram consists of piecewise (answer) forces.
A simply supported beam of hollow rectangular cross section is 100mm deep and 60mm wide with a wall thickness of 10mm. The beam has a span of 6m and carries a load as shown . Neglecting the weight of the beam draw a bending moment diagram and calculate the maximum bending moment. And determine the maximum bending stress in the material.
A beam (assume weightless) is placed horizontally with the left end as a pinned support and right end as a roller support. The beam is subject to three vertically applied forces as shown right. Please find: a) Show shear force plot b) Show moment plot