Question 3 Water flows through a 5 cm diameter pipe with a velocity of 4.5 m/s as shown in Figure Q3. The relative roughness of the pipe is 0.004 and the loss coefficient for the exit is 1.0. The dynamics viscosity of water is 1.12x10³ N.s/m². (a) Write a balanced energy equation. (b) Calculate the Reynold number in the water pipe, (c) Determine the friction factor, and (d) Determine the height, h, to which the water rises in the piezometer tube, in m. 4.5 m/s Open 5 cm 2.5 m TL 2.5 m

Question 3 Water flows through a 5 cm diameter pipe with a velocity of 4.5 m/s as shown in Figure Q3. The relative roughness of the pipe is 0.004 and the loss coefficient for the exit is 1.0. The dynamics viscosity of water is 1.12x10³ N.s/m². (a) Write a balanced energy equation. (b) Calculate the Reynold number in the water pipe, (c) Determine the friction factor, and (d) Determine the height, h, to which the water rises in the piezometer tube, in m. 4.5 m/s Open 5 cm 2.5 m TL 2.5 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A horizontal water pipe of 15 cm diameter converges to a 7.5 cm diameter. If the pressures at the two sections are 400 kPa, and 150 kPa respectively, calculate the flow rate of water in cubic meters per second
Oil flows at 55.9L/s in a pipe of 160mm diameter and 50m length. SG of oil is 0.9 and viscosity is 0.04 Pa-sec. If head loss is 5.22m, determine: a. Mean Velocity of flow (m/s) b. Type of flow c. Friction Factor d. Velocity at the centerline of pipe (m/s) e. The shear stress at the wall of the pipe (Pa)
Please indicate the given and illustration A steel pipe, 3.5 km long x 80 cm diameter x 1 cm wall thickness, conveys water at the rate of 1.75 m3/s. Determine the increase in pressure when a valve provided at the downstream end of the pipe is closed instantaneously. Consider pipe to be elastic and take bulk modulus of water K = 2x109 N/m2; Modulus of elasticity of steel E = 2x1011 N/m2. After determining the surge of pressure in the pipe, compute the following: A) The Longitudinal Stress of the Pipe in Pascal. B) The Circumferential Stress of the Pipe in Pascal.
Water flows through a 61-cm by 122-cm conduit at a flow rate of 2000 CMH. The horizontal conduit was 100 m in length and was made of sheet metal. Calculate the pressure drop (i.e. inlet pressure minus outlet pressure) in Pa. Take the dynamic viscosity of water to be 1.0 CP and its density to be 1000 kg/m³. Take the local gravitational acceleration to be 9.81 m/s².
Oil of viscosity 10E-3 Pa-s and specific gravity 0.90, flows through 60 m of 100mm diameter pipe and the pressure drop 13.8 kPa. What will be the pressure drop for a second oil of viscosity 30E-3 Pa.s and the specific gravity 0.95 flowing at the same rate through the pipe? Assume the pipe wall to be smooth.A. 19.4 kPaB. 98.7 kPaC. 142.2 kPaD. 192.5 kPa
The pressure in a section of a horizontal pipe of diameter d1 = 2.0 cm is p1 = 142 kPa. The water flows through the pipe at a volumetric flow rate V = 2.8 L/s. If the pressure at a certain point is reduced to p2 = 42.6 kPa, due to a throttling of a pipe section, what should the diameter d2 of the throttling section be? Consider the density of water ρ = 1.0 g/cm3. Choose the correct option:
A 1.0 m radius cylindrical industrial tank filled with viscous oil to a level at a height h from its base, must be drained through a tube with a radius of 0.2 m and length L, connected to its base. The speed profile of oil in the drain tube can be described by the equation below. Where v is the oil speed, vmax is a = maximum oil speed, r is the radius, and R is the tube radius. Considering this problem situation, do what is asked in the following items, justifying your answers. a) What is the volume, in liters, of oil removed from the tank after 10 seconds, if the maximum discharge speed does the oil reach 0.35 m/s? Data: π ≈ 22/7; 1 m3 = 1000 L. b) What flow regime does the system operate? Demonstrate. Data: specific mass of oil = 800 kg/m3, specific mass of water = 1000 kg/m3, oil viscosity = 0.056 Pa.s e viscosity of water = 0.001 Pa.s.
The ethanol solution is pumped into a vessel 25 m above the reference point through a 25 mm diameter steel pipe at a rate of 10 m3 / hr. The pipe length is 35m and there are 2 elbows. Calculate the power requirements of the pump. The properties of the solution are density 975 kg / m3 and viscosity 4x 10-4 Pa s. a. Reynold number = Answer b. Loss of Energy along the straight pipe = Answer J / kg. c. Losing Energy at curves = Answer J / kg. d. Total energy to overcome friction = Answer J / kg. e. Energy to increase water according to height = Answer J / kg. f. The theoretical energy requirement of the pump ethanol / second = Answer J / kg. g. Actual pump power requirement = Answer watt.
A 100mm circular sharp edge hole in the end of a 150mm pipe discharges oil (s = 0.90). The vapor pressure in the closed tank is – 20 kPa, and the pressure head on the centerline of the pipe directly upstream from the orifice is 9m of oil. There is no submersion of the discharge. If CV = 0.97 and Q = 83 liters/s, find the discharge coefficient. Answer: C = 0.68
SAE 30 oil at 20°C flows in the 2.5-cm-diameter pipe as shown in the figure below, which slopes at 37°. For SAE 30 oil, take ρ = 891 kg/m3 and μ = 0.29 kg/m⋅s. Determine the flow rate in m3/h. The flow rate is m3/h.
The ethanol solution is pumped into a vessel 25 m above the reference point through a 25 mm diameter steel pipe at a rate of 8 m3 / hr. The pipe length is 40 m and there are 2 elbows. Calculate the power requirements of the pump. The properties of the solution are density 975 kg / m3 and viscosity 4x 10-4 Pa s. a. Reynold number = Answer. b. Loss of Energy along the straight pipe = AnswerJ / kg. c. Losing Energy at curves = AnswerJ / kg. d. Total energy to overcome friction = AnswerJ / kg. e. Energy to increase water according to height = AnswerJ / kg. f. The theoretical energy requirement of the pump ethanol / second = AnswerJ / kg. g. Actual pump power requirement = Answerwatt.
Water enters a piping system with a diameter of 0.1016 m from a reservoir with a volumetric flow rate of 0.1893 m³/min. Determine whether the flow is laminar or turbulent if, during the winter, the dynamic viscosities of μ = 1.308x 10-3 Pa 's and 0.687x10-3 Pa s during the summer. What is the length of pipe necessary to reach a fully developed flow?