Question #4 Bar (1) in the figure has a cross-sectional area of 0.75 in². If the normal stress in bar (1) must be limited to 30 ksi, determine the maximum load P (in kips) that may be supported by the system. The connections at A, B and C are pins. A 6 ft D B (1) 4 ft

Question #4 Bar (1) in the figure has a cross-sectional area of 0.75 in². If the normal stress in bar (1) must be limited to 30 ksi, determine the maximum load P (in kips) that may be supported by the system. The connections at A, B and C are pins. A 6 ft D B (1) 4 ft

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.4.16P: An aluminum tube AB with a circular cross section has a sliding support at the base and is pinned at...

See similar textbooks

Related questions

Q: * The correct relationship among displacement thickness d,momentum thickness m and energy thickness…

Q: Example procedure of Level, Flow, Pressure and Temperature control system

A: Given Level control system Pressure control system Temperature control system To find Procedure

Q: There are two turbine stages with a reheater in between, as shown below and the following conditions…

A: Given:P1=1200 KPa T1=1200 KP2=350 KPaP3=350 KPaT3=1200 KP4=100 KPa

Q: solution with proper derivatives / in -- Box or indicate your final answe ~, ure g= 9.81. man is…

A: Given as, Weight= 50 kg, Mass = 2 kg.

Q: beam at quarter of the

A: Given ,

Q: The block A is subjected to a pulling force p along the cable. If the weight is 100 N and the…

Q: 4. A load P is applied concentrically to the bar shown. If the allowable normal stress is 76 ksi,…

Q: Q4: The pump shown in figure (2) adds 25 kW to the water and causes a flow rate of 0.04 m³/s.…

Q: A beam with the cross-section shown is carrying a bending moment of M. Calculate the maximum bending…

Q: Sketch a free-body diagram of each element in the figure. Compute the magnitude and direction of…

A: Introduction: Magnitude of force: The total of all the forces operating on an item is defined as the…

Q: he right-angle bar with equal legs weighs /7.1 lb and is freely hinged to the vertical plate at C.…

A: Solution- Given data- m = 7.1 lb

Q: An unsteady, incompressible, velocity field is given by the following vector: V = (u, v, w) = (−7t…

A: Velocity vector, V→=u,v,w=-7t+3.5xy+2.2yi→+2t+3x-1.6yj→+5+4zk→Point, x,y,z,t=-1,2,1,2

Q: The rod has a diameter of 0.5 in. and a weight of 5 lb/ft. i) Calculate the torque and bending…

A: Given data: Diameter of the rod D = 0.5 in = (0.5/12) = 0.04167 ft weight of the rod, W = 5 lb/ft If…

Q: Water flows over a waterfall 328 Ft in height. Take 2.204 lb of the water as the syste and assume…

A: given : h = 328 ft h= 328/3.281 m h = 100m m = 2.204 lb m= 2.204/2.205 kg m=0.9997 kg

Q: Q5: As shown in figure (5). What is the water horsepower of the pump? The pipes characteristics are…

Q: The amount of heat needed to raise the of a unit mass of material by one degree is called…

A: Given Statement:- The amount of heat needed to raise the temperature of a unit mass of material by…

Q: Read the question carefully before answering. Show complete solution with proper derivatives /…

Q: Q1/ List the material properties for the following products. What is the new innovation for these…

A: The process of designing any physical thing includes the choice of materials. The major objective…

Q: Q.48 A 2.0 meter long conical diffuser 20 cm diameter at the upstream end has 80 cm diameter at…

A: Answer: (a) The local acceleration: 0.15068 m/s2 (b) The convective acceleration: -0.33532 m/s2 (c)…

Q: YZ 1- Using the CNC milling machine, carve a 5cm x 5cm wax block with your name initials, using ERAS…

A: To find: Let's list the steps of carving a 5 cm by 5 cm wax block using the CNC milling machine.

Q: stress-strain curves

A: a) The material which has more plastic region is more ductile. The rank of material according to…

Q: 35 and wet bulb temp at 25c Dry bulb temp what is the humidity percantage?

Q: Question 1 Aluminum rod E = 10400 ksi Allowable axial deformation= 0.3 in. Tension in the rod= 2300…

Q: Explain with neat sketch, “Galvanizing” heat treatment process.

A: Galvanizing: It is a process to make a coating of layer of zinc on steel or iron by dipping the…

Q: Find the slope deflections using any unit load method in the text book. For the beam shown in figure…

Q: 4- Calculate the coefficient of three different objects that start moving at the following angles:…

A: GIVEN DATA- ANGLE OF REPOSE GIVEN FOR THREE OBJECT WE HAVE TO FIND COEFFICIENCT OF FRICTION

Q: A 2 cm thick steel pipe (thermal conductivity 43 W/[m °C]) with 6 cm inside diameter is being used…

Q: Q3: Three pipes (A, B and C) are interconnected as shown in figure (3). Determine the flow rate in…

A: Applying continuity equation on the pipes, The flow rate in pipe C is the combination of both the…

Q: i need the answer quickly

A: Given

Q: The A 8000 lb TIT 6000 lb -4 ft. 10.000 lb 4 ft-> 4 4 ft → 4 fi B

Q: The uniform slender bar AB has a mass of 6.7 kg and swings in a vertical plane about the pivot at A.…

Q: * Determine the water flow rate of hydraulic system shown in Fig. . (neglected the minor losses)

Q: The resultant force acting of the uniformly distributed loading dependson the distance between the…

Q: 4. A given beam, of L-3m and El-6000kN.m², is subjected to a uniformly distributed load (w). The…

A: Given

Q: You are asked to determine the heat loss from a very thin spherical cap containing a hot fluid at a…

Q: detailed solution) The velocity of a particle which moves along the a linear reference axis is…

Q: An open vessel in the form of a frustum of a cone with a radius of 1.2m (bigger base), the smaller…

Q: A 70 kg man falls onto a platform with negligible weight from a height of 1.5m. It is supported by 3…

A: Given data: M=70 kgh=1.5 kgkL=7.30 kN/mkS=21.9 kN/mx=0.1 m Need to determine the compression in each…

Q: B: An open cylindrical tank (1.2m) in diameter and (1.8m) deep is filled with water and rotated…

Q: A refrigerator is to maintain eatables kept inside at 9°C. If room temperature is 36° C, calculate…

A: From the data given in the question, Recommended internal refrigerator temperature = TL = 9 oC =…

Q: SAVAL. 3. Choose the most appropriate material from your point of view that can be used to produce…

A: For any manufacturing it may be components or whole product.the material selection is very essential…

Q: 3. A platform supported by 4 parallel springs : 2 long and 2 short springs, have a spring of 1.30…

A: Given data: k1=k2=1.3 kN/mk3=k4=10.95 kN/mm=35 kgh=1.5 mx=0.1 m Need to determine the compression in…

Q: Q1/ The gauge pressure of the air in the tank shown in (Fig.1) are measured to be 80 kPa. Determine…

A: The differential height of the mercury column: h = 0.582 m

Q: An air-conditioning system to be installed in a factory with sensible and latent cooling loads of…

Q: Example 5.7 What is the maximum work in turbine that can be obtained in a steady-state flow process…

A: n = number of moles of nitrogen = 1 turbine inlet temperature, T1 = 800 K Turbine inlet Pressure, P1…

Q: The Carnot cycle is a reversible cycle and produces work

A: Carnot cycle is an Ideal cycle in which all the processes are reversible.

Q: S' shing a loaded rotating

A: Given as, F=4t3+1 M=1kg r=0.5m t=2sec…

Q: Q2/ Water have a surface tension of 0.4 N/m. In a 3 mm diameter vertical tube if the liquid rises 6…

Q: W at a speed of 1 rev/s. The screw has a major diameter of 36mm and a pitch of 6mm. The frictional…

A: Given as, Power=3KN =3000W N=1rev/s d=36mm p=6mm u=0.14 for…

Q: JA -7- Wo B I.

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A sign for an automobile service station is supported by two aluminum poles of hollow circular cross section, as shown in the figure. The poles are being designed to resist a wind pressure of 75 lb/ft" against the full area of the sign. The dimensions of the poles and sign are hx= 20 ft, /r =5 ft, and h = 10 ft. To prevent buckling of the walls of the poles, the thickness e is specified as one-tenth the outside diameter d. (a) Determine the minimum required diameter of the poles based upon an allowable bending stress of 7500 psi in the aluminum. (b) Determine the minimum required diameter based upon an allowable shear stress of 300 psi.
A two-story building has steel columns AB in the first floor and BC in the second floor, as shown in the figure. The roof load P:equals 400 KN, and the second-floor load P-, equals 720 kN. Each column has a length L = 3.75 m. The cross-sectional areas of the first- and second-floor columns are 11,000 mm" and 3900 mm", respectively. (a) Assuming that E = 206 GPa. determine the total shortenings aof the two columns due to the combined action of the loads Ptand P,. (b) How much additional load P0can be placed at t he top of t he column (point C) if t he total shortening: SACis not to exceed 4.0 mm?
A steel pad supporting heavy machinery rests on Four short, hollow, cast iron piers (see figure). The ultimate strength of the cast iron in compression in 50 ksi. The outer diameter of the piers is d = 4.5 in, and the wall thickness is t = 0.40 in. Using a factor of safety of 3.5 with respect to the ultimate strength, determine the total load P that can be supported by the pad.
The figure shows an idealized structure consisting of rigid bars ABC And DEF joined by a linearly elastic spring ß between C and D. The structure is also supported by translational elastic support ß at B and rotational elastic support ßRat E. Determine the critical load Pcrfor the structure.
A pressurized circular cylinder has a sealed cover plate fastened with steel bolts (see figure). The pressure P of the gas in the cylinder is290psi, the inside diameter D of the cylinder is 10.0 in., and the diameter dBof the bolts is 0.50 in. I f the allowable tensile stress in the bolts is 10,000 psi, find the number n of bolts needed to fasten the cover.
An aluminum tube AB with a circular cross section has a sliding support at the base and is pinned at the top to a horizontal beam supporting a load Q = 200 kN (sec figure). Determine the required thickness t of the tube if its outside diameter d is 200 mm and the desired factor of safety with respect to Eu 1er buckling is n = 3.0. (Assume E = 72 GPa.)
A steel cable with a nominal diameter of 25 mm (see Table 2-1) is used in a construction yard to lift a bridge section weighing 38 kN. as shown in the figure. The cable has an effective modulus of elasticity E = 140 GPa. (a) If the cable is 14 m long, how much will it stretch when the load is picked up? (b) If the cable is rated for a maximum load of 70 kN, that is the factor of safety with respect to failure of the cable?
A steel bar has a square cross section of width b = 2.0 in. (sec figure). The bar has pinned supports at the ends and is 3.0 ft long. The axial forces acting at the end of the bar have a resultant P = 20 kips located at distance e = 0,75 in, from the center of the cross section. Also, the modulus of elasticity of the steel is 29,000 ksi. Determine the maximum compressive stress max, in the bar. If the allowable stress in the steel is 18,000 psi, what is the maximum permissible length Lmaxof the bar?
A vertical pole of aluminum is fixed at the base and pulled at the top by a cable having a tensile force T(see figure). The cable is attached at the outer edge of a stiffened cover plate on top of the pole and makes an angle a = 20° at the point of attachment. The pole has length a = 2.5 m and a hollow circular cross section with an outer diameter d2= 280 mm and inner diameter d1= 220 mm. The circular cover plate has diameter 1.5d2 Determine the allowable tensile force Tallow in the cable if the allowable compressive stress in the aluminum pole is 90 MPa.
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
Rigid bar ACB is supported by an elastic circular strut DC having an outer diameter of 15 in. and inner diameter of 14.4 in. The strut is made of steel with a modulus elasticity of E = 29,000 ksi. Point load P = 5 kips is applied at B. Calculate the change in length of the circular strut DC. What is the vertical displacement of the rigid bar at point B?
A metal bar AB of a weight Ills suspended by a system of steel wires arranged as shown in the figure. The diameter of the wires is 5/64 in., and the yield stress of the steel is 65 ksi. Determine the maximum permissible weight W max for a factor of safety of 1.9 with respect to yielding.