In mechanical fluid $008Determine the water flow rate ofhydraulic system shown in Fig.. (neglected the minor losses)L₁ = 50A=0.02diz0.02mL₂=100m·1₂2=0= 0.005d₂50.0lmAir0.00016 m3/sec O10 m3/sec O0.016 m3/sec O0.16 m3/sec O0.0001 m3/sec O

Answered: Image /qna-images/answer/7c5adcec-7b12-411c-8bc9-4c951c91efdd.jpg

Answered: * Determine the water flow rate of…

Engineering

Mechanical Engineering

* Determine the water flow rate of hydraulic system shown in Fig. . (neglected the minor losses)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A water pump is used to pump water from one large reservoir to another large reservoir that is at a higher elevation. The free surfaces of both reservoirs are exposed to atmospheric pressure, as sketched in Fig. The dimensions and minor loss coefficients are provided in the figure. The pump’s performance is approximated by the expression Havailable = H0 − aV.2 , where the shutoff head H0 = 125 ft of water column, coefficient a = 2.50 ft/(gpm)2 , available pump head Havailable is in units of feet of water column, and capacity V. is in units of gallons per minute (gpm). Estimate the capacity delivered by the pump
Provide clear and complete solution as well as diagram. The initial condition of air in an air compressor is 97 kPa and 27 oC and discharges air at 350 kPa. The bore and stroke are 250 mm and 280 mm, respectively with percent clearance of 6 percent running at 310 rpm. Find the volume of air at suction in m3/hr. A. 232.61 C. 156.34B. 289.16 D. 135.23
During a test run of a Pelton wheel turbine, the pressure at the nozzle was 2.25 MPa when water flowing in the penstock at 1.7 cubic meter/sec. The penstock diameter is 600 mm. Determine: a. The effective head in meters 255.09 231.27 241.36 b. The Water Power (WP) in kW 3,855 4,226 3,413 c. The turbine power in kW if the turbine efficiency is 80% 3,277 3,413 3,084 d. the generator output in MW if the generator efficiency is 92% 2.837 3.139 2,837
Paolo owns a hydroelectric power generating system as shown in HG008. Water flows from an upper reservoir to a lower one passing through a turbine at the rate of 150 lps. The total length of pipe connecting the two reservoir is 100 m. The pipe diameter is 250 mm and the Hazen – Williams coefficient is 120. The water surface elevations of reservoirs 1 and 2 are 197 m and 50 m, respectively. Find the velocity of flow in pipe in m/s.
A water pump is used to pump water from one large reservoir to another large reservoir that is at a higher elevation. The free surfaces of both reservoirs are exposed to atmospheric pressure, as sketched in Fig. The dimensions and minor loss coefficients are provided in the figure. The pump’s performance is approximated by the expression Havailable = H0 − aV.2 , where shutoff head H0 = 24.4 m of water column, coefficient a = 0.0678 m/(Lpm)2 , available pump head Havailable is in units of meters of water column, and capacity V. is in units of liters per minute (Lpm). Estimate the capacity delivered by the pump. A
A Kaplan turbine has the following specifications: H =25 ft., N=400 rpm; power = 650 hp. If the efficiency of the unit is 90%, estimate (a) the flow rate, (b) approxi-mate diameter of the runner, (c) turbine setting to avoid cavitation if the location is at sea level, and (d) turbine setting to avoid cavitation if the location of the unitis at an elevation of 5000 ft. The local temperature is 60°F.Ans: (a) Q=254 cfs; (c) Hs=5.8 ft.; (d) 0.12 ft.
A reservoir supplies water through 100 m of 30-cm-diameter cast iron pipe to a turbine that extracts 80 hp from the flow. Given that Δz = 30 m. The water then exhausts to the atmosphere. Neglect minor losses. For water at 20°C, take ρ = 998 kg/m3 and μ = 0.001 kg/m-s. Take π = 22/7. In determining the flow rate of the given flow, two solutions are obtained. Are both the solutions valid? Yes or no?
As seen in Figure 3 below, the water from the tank 1 is pumped to the tank 2 with a flow rate of 5,664 liters/s, passing through a pipe with a diameter of 50.8 mm and a length of 121.92 m. Some of the local losses in the system are also shown on the figure. Calculate the effective power of the pump by taking the relative roughness ɛ / d = 0.001 Note: For all questions, pwater = 1000 kg/m³, g=9.81m/s^2 , the kinematic viscosity of water is 1.0219x106 m²/s and the questions can be solved by accepting the values that are not given.
Please show complete diagrams and solutions T.Y :) Use Bernoulli's Energy Equation Dislike if not followed A 24 in. pipe conducts water from reservoir A to a pressure turbine (elev. = 15'), which discharges through another 24 in. pipe into tailrace B (elev. = 0'). The loss of head from A to 1 is 5 times the velocity head in the pipe and the loss of head from 2 to B is 0.2 times the velocity head in the pipe. What must water surface elevation at the reservoir be maintained such that the energy given up in the turbine is 552 hp? Assume discharge equals 25 cfs. Express all dimensions in English units.
A certain hydropower plant is being supplied by river flow of 900 cubic ft/sec and the head on the site is 200 ft. To develop maximum capacity it was proposed to install 2 turbines, one of which is 1.5 times the capacity of the other. Both turbine units are assumed to have efficiency of 85%. Determine (a) the total power developed, (b) what is the power developed by turbine #1 and by turbine #2 and (c) Rotative speed of each turbine unit assuming specific speed equal to 70 rpm.
Water flows at 15 oC in an ASME type venturimeter. In this venturimeter, find the water flow rate according to D = 100mm, d = 50mm, P = 9062 Pa. (C = 0.98 will be taken and p = 998.3 kg / m3, u = 1.12x10 ^ -3kg / m.s)
9.7. Through a hydraulic turbine flow 2.8 m3/s of water. On the 1 m inlet pipe at elevation 43.5,a pressure gage reads 345 kPa. On the 1.5 m discharge pipe at elevation 39, a vacuum gage reads150 mm of mercury. If the total head lost through pipes and turbines between elevations 43.5and 39 is 9 m, what power may be expected from the machine?