QUESTION 4 If we have a zener diode with a TEMPCO = of 1.9 mV/K. At a current of -2mA and a voltage of --4.4 V, what change in temperature in K is needed to change the zener voltage by -76 mV at a constant current of -2mA. 1.8F = 1K. Answer should be to three significant digits with fixed point notation.

QUESTION 4 If we have a zener diode with a TEMPCO = of 1.9 mV/K. At a current of -2mA and a voltage of --4.4 V, what change in temperature in K is needed to change the zener voltage by -76 mV at a constant current of -2mA. 1.8F = 1K. Answer should be to three significant digits with fixed point notation.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2P: The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where...

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
Suppose we have a junction diode operating at a constant temperature of 300 K. With a forward current of 1 mA, the voltage is 600 mV. Furthermore, with a current of 10 mA, the voltage is 700 mV. Find the value of n for this diode.
In a 1-phase full wave bridge rectifier with Vs = Vm sin ωt, with R load & ideal diodes. The expression for the average value of the output voltage is 2Vm/π Select one: True False
In your own words and with the aid of suitable diagrams, describe the following: Explain what the barrier potential is and how it is developed in pn junction diode. What is the typical value of the barrier potential for a silicon diode?
Zener diodes are special purpose diodes designed to operate in their breakdown regions. Describe the working principle and characteristics of a typical Zener diode found in the market place. The Zener-diode regulator circuit shown below is to be used to provide a stabilised output to the load. The zener diode characteristic is also shown. Find the load voltage and source current if the battery voltage is 20 V, series resistance is 1.4 kohm and load resistance is 6 kohm
What is an ideal diode? Draw its volt–ampere characteristic. After solving a circuit with ideal diodes, what check is necessary for diodes initially assumed to be on? Off?
Two ideal diodes are placed in series, pointing in opposite directions. What is the equivalent circuit for the combination? What is the equivalent circuit if the diodes are in parallel and pointing in opposite directions?
In the circuit given in the figure, since Vi is a square wave with a frequency of 1 kHz and an amplitude varying between +5V and -5V; Vi and Vo voltages one after the other and in scale; a) Draw with Zener diode is not active ? b) Draw with the Zener diode on? (Assume the diodes in the circuit are ideal)
In each of the ideal-diode circuits show below V1 is a 1kHz, 10-V peak sine wave. Sketch the wave form resulting at V0. What are its positive and negative peak values?
Determine Q-point for the diodes in the circuit given below using the ideal diode model where, R1 = 12.2 kΩ, R2 = 16 kΩ, and R3 = 14 kΩ. (Note: Label the diodes from left to right.)
Forward bias current equation given For n=1 and Is= 10pA. Plot the I vs VD Forward bias characteristics of a PN Diode at room temperature by draw a graph and table of the graph. (b)Calculate and find Rd. (full step please, I dont understand to solve it)
Two identical Schottky diodes are connected in series, one in the forward and the other in reverse direction, see figure. Assume the reverse saturation current, IS, of each diode to be known. Derive he current-voltage curve I(V) of this circuit. Plot it with the ratio I / IS on the y-axis and V / Vth on the x-axis. Make sure to cover a broad range of voltages, say, from –10 Vth to 10 Vth.