Question 4: The bend with an outlet diameter (D₂) of 5 cm discharges freely as shown in figure below. If the pressure at section 1=150 kPa, assume the difference in elevation between section 1 and 2 is negligible and determine: ( 1. The flow rate in the system 2. The magnitude of reaction of the pipe in X-direction (Fx) only in kN, needed to hold the bend in place. D₁= 15 cm D₂# 5 cm 30°

Question 4: The bend with an outlet diameter (D₂) of 5 cm discharges freely as shown in figure below. If the pressure at section 1=150 kPa, assume the difference in elevation between section 1 and 2 is negligible and determine: ( 1. The flow rate in the system 2. The magnitude of reaction of the pipe in X-direction (Fx) only in kN, needed to hold the bend in place. D₁= 15 cm D₂# 5 cm 30°

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water flows upward in a vertical 300-mm pipe at the rate of 0.222 m /s. At point A in the pipe the pressure is 210 kPa. At B, 4.57 m above A, the diameter is 600 mm, and the lost head A to B equals 1.83 m. Determine the pressure at B. indicate the free body diagram
In the test of the reaction turbine, the water flowing over the weir in the tailrace was found to be 39.8 ft3 /s. The leakage into the tailrace was found to be 1ft3 /s. The elevation of the centerline of the shaft above, the surface of tailwater was 12.67ft. The diameter of the turbine intake was 30in and the pressure at this section was measured by a mercury U-tube. The readings in the two sides of the mercury U-Tube were 10.556 ft and 0.900 ft, the zero of the scale being at a level 3.82ft below that of the centerline of the turbine shaft. The generator output was 391.8 kW, friction and windage loss 13.8 kW, iron loss 2.0kW and armature loss of 4.4kW. The specific gravity of the mercury used was 13.57. Calculate the efficiency of the turbine.
Write legibly 6. The piping shown in the figure is a parallel-pipe system carrying water at normal temperature. Pressure head at junction X is 76 m, while that at Y is 48 m. If the inflow at junction X is 0.35 cum/s, determine the flow of water at each branch of the loop. Assume C = 120 for all pipes. determine: a. flow in pipe A: ____________m3/s 1b. flow in pipe B: ____________ m3/s c. flow in pipe C: _____________ m3/s
From a very large tank with an absolute pressure of 3 bar, the water is discharged to the atmosphere by means of 2 smooth pipes of 100 m length, 1 m and 50 m long, connected in series. The height difference between the water level in the tank and the outlet is 50m, and the diameters of the pipes are 50mm and 100mm, respectively. In addition, a 500kPa turbine is placed on the 2nd Pipe. a) Draw the system roughly, show the dimensions on it.b) Calculate the exit velocity of the water from the 2nd pipe, ignoring the local losses.
Using the situation below, how would I determine the net resultant force exerted on the reducer by the water? In this situation, water is flowing horizontally in a pipe that has a diameter of 25cm. This water is flowing at 8 m/s and at 300 kPa gage it enters a 90 degree bend reducing section. This bend reducing section is connected to a vertical pipe that has a diamater of 15cm. Moreover, the inlet of the bend is 45 cm above the exit. Here, fricition and gravity are negligible and the momentum flux correction factor is 1.04.
A venturi meter is introduced in a 300 mm diameter horizontal pipeline carrying a liquid under a pressure of 150 kPa. The throat diameter of the me- ter is 100 mm and the pressure at the throat is 400 mm of mercury below atmosphere. If 3% of the differential pressure is lost between inlet and the throat, determine the flow rate of the pipeline. PLEASE USE BERNOULLI'S ENERGY EQUATION. INCLUDE COMPLETE SOLUTION
Water (@ 45°C) is flowing in a horizontal pipe with an increasing cross-sectional area. The measured pressure drop in the piper is 4.1 psia. If the cross-sectional area at the exit of the pipe is 2x the cross-sectional area at the entrance, what is the V of the water as it enters the pipe? Assume that frictional losses are negligible .
The system consists of 1200 m of 5 cm cast iron pipe, two 45° and four 90° flanged long-radius elbows, a fully open flanged globe valve, and a sharp exit into a reservoir. If the elevation at point 1 is 400 m, what gage pressure is required at point 1 to deliver 0.005 m3/s of water into the reservoir? Use the following: v = 1 x 10-6 m2/s Kentrance = 0.5 Kexit = 1 Kvalve = 6.9 f = 0.0316 γ = 9810 N/m3 Choices: 3.44 Mpa 1.02 MPa 3.48 Mpa 1.00 MPa None of the choices
An axial fan having a hub diameter of 0.4 m and a hub ratio of 0.5 delivers a flow rate of 5 m3/s at a rotational speed of 1800 rpm. If the chord length at mean radius is 0.12 m, determine the pressure change across the fan using this formula
Calculate the total head of the system below. Assume a flow of 70 m³/h and that the pressure drops in the suction and discharge are 3 m and 4 m, respectively. ZA = 15m, ZB = 5m and ZC = 5m.
The horizontal pipe length is 180 m and the vertical pipe length is 24 m in the fire protection system, which is formed with a water tower and pipeline, 1 threaded 90 ° elbow (Kd = 0.9) on the pipeline and 1 slide valve at the pipe outlet (fully open position Kv = 0.2). Since the pipe material is cast iron and its diameter is 4 ”(101.6 mm), determine the maximum flow rate in the pipe considering the losses. Assume that the water level in the tower remains constant and the kinematic viscosity of the water is 1.124x10-6 m2 / s. Show your readings by drawing on the attached Moody diagram.
(Q29) A horizontal pipe of diameter 550 mm is suddenly contracted to a diameter of 300 mm. The pressure intensity in large pipe is given as 14 N/cm2 and the flow velocity in the larger pipe is 2 m/s. Find:- (a) The rate of flow of water through a horizontal pipe. (b) Loss of head due to sudden contraction. (c) Pressure intensity in smaller pipe.