QUESTION 4The sluice gate, shown in figure 4, hinges freely about A. Calculate the force exerted onthe stop block if the sluice gate is 4 m high and 6 m wide.[1Figure 46 mWater4 mASluice gateStop block

Name: QUESTION 4The sluice gate, shown in figure 4, hinges freely about A.
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: QUESTION 4The sluice gate, shown in figure 4, hinges freely about A. Calculate the force exerted onthe stop block if the sluice gate is 4 m high and 6 m wide.[1Figure 46 mWater4 mASluice gateStop block

To Find : The exerted force on the step block. Given : The height of gate is h=4 m The width of…

Answered: QUESTION 4 The sluice gate, shown in…

Engineering

Mechanical Engineering

QUESTION 4 The sluice gate, shown in figure 4, hinges freely about A. Calculate the force exerted the stop block if the sluice gate is 4 m high and 6 m wide. A

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Note: Please state what formula you are using. And please be clear and detailed with your solution. Atleast explain. It will help me, thanks. Problem: A Triangular gate having a horizontal base of 1.30 m and an altitude of 2 m is inclined 45o from the vertical with vertex pointing upward. The base of the gate is 2.70 m below the surface of oil (s = 0.80). What normal force must be applied at the vertex of the gate to open it? Show figure
Gate AB in the Figure is 6 ft wide into the paper, hinged at A, and restrained by a stop at B. Compute the force on stop B, if the water depth h = 11 ft.
A dam with triangular cross section holds back a body of water. The dam has height h. The dam is made of concrete, which has speci…c gravity 3.1. What is the maximum angle, , for which thedam will not tip over about point O?
The cover in the figure is hinged at the center O and has a fixed width w = 5 m. The equation of the surface is x = y2 / a (a = 3 m), the depth of the water to the right of the cover is D = 4 m. Find the magnitude of the applied force (Fa) as shown. Take the density of water as 999kg / m3.
In Fig., gate AB is 5 ft wide into the paper, and stopB will break if the water force on it equals 9200 lbf. Forwhat water depth h is this condition reached?
Please be clear with your solution. Make an explanation for the formula and solution you used. Problem: A Triangular gate having a horizontal base of 1 30 m and an altitude of 2 m is inclined 45 o from the vertical with vertex pointing upward The base of the gate is 2 70 m below the surface of oil s 0 80 What normal force must be applied at the vertex of the gate to open it? Show figure
EMERGENCY!!!! The cover in the figure is hinged at the center O and has a fixed width w = 5 m. The equation for the surface is x = y2 / a (a = 3 m), the depth of the water to the right of the cover (D = 4 m). Find the magnitude of the applied force (Fa) as shown.
The tank of water in Fig. is 12 cm wide into the paper.If the tank is accelerated to the right in rigid-body motion at6.0 m/s 2 , compute ( a ) the water depth on side AB and ( b ) thewater-pressure force on panel AB . Assume no spilling.
A dam is used to store water, and a rectangular gate which is hinged at its bottom edge is used to control the flow as shown in figure 1. For this gate, width = 1 m (in the direction of the page) , α = 65°, h1 = 1 m, and h2 = 5 m. Figure 1: Schematic for task 1. (Giancoli et al.) a. Describe the forces acting on the gate and the center of pressure. b. Determine the resultant force and the position of the center of pressure on the gate. c. What is the maximum gate mass that is needed for it not to fall? d. Show yc, yR, hc, hR, FR, and W on the free body diagram.
A 6-m-high, 5-m-wide rectangular plate blocks the end of a 5-m-deep freshwater channel, as shown in Figure. The plate is hinged about a horizontal axis along its upper edge through a point A and is restrained from opening by a fixed ridge at point B.Determine the force exerted on the plate by the ridge.
In the figure shown, stop B will break in the force on it reaches 40 kN. Find the critical water depth (h-bar) the length of the gate perpendicular to the sketch is 1.5m. Ans (5.77m)
An underwater gate 8 m wide is held closed by a force, F, as shown in the figure. If the force is applied at the middle of the gate, what is the minimum value required to keep the gate closed? take density of water= 996kg/m3