Question 5: a) Formulate the Newton-Raphson power flow problem for the two-bus problem shown in Fig.Q5. (b) Calculate the bus #1 voltage using the N-R algorithm. The power mismatch is to be less than 0.001. Slack bus Bus 2 Busl z=0+ j0.2 V:= 1.012 0° 600 MW 200 MVAr Base 1000 MVA Fig. Q5: Two bus power flow problem

Question 5: a) Formulate the Newton-Raphson power flow problem for the two-bus problem shown in Fig.Q5. (b) Calculate the bus #1 voltage using the N-R algorithm. The power mismatch is to be less than 0.001. Slack bus Bus 2 Busl z=0+ j0.2 V:= 1.012 0° 600 MW 200 MVAr Base 1000 MVA Fig. Q5: Two bus power flow problem

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter14: Power Distribution

Section: Chapter Questions

Problem 14.17P

See similar textbooks

Similar questions

In the Gauss-Seidel iterative method of power flow, describe the differences of the computational procedures used for a PV bus and a PQ bus.
Determine the bus voltages at buses 2 and 3 after 1st iteration using GS method. Take the acceleration factora=1.6
Explain load flow analysis of Radial distribution system by Fuzzy logic with neat diagram.
1. List out how does a priority method varies from dynamic programming method in Unit commitment problems. 2. Contribution of load flow studies to erect new power station?
In a load flow problem solved by Newton Raphson method with polar coordinates, the size of the jacobian is 100*100. If there are 20 PV buses in addition to PQ buses and a slack bus, the total number of buses in the system is _____
With the system shown in figures, use 100MVA as system base, and 230 kV as base voltage along the transmission line. 1. Build the Y-bus matrix without the Load. What is the element Y12 in susceptance value? 2. If you are to convert the real power load to a shunt conductance, what is the value of the conductance in per unit?
What is the need to conduct power flow analysis? Discuss about data needed and bus types too.
a) Find the Y-bus power system in rectangular and polar coordinates.b) Specify the type of each bus, and the known/unknown values. c) What is the real and reactive power injections at buses 2 and 3?
With the system shown in the figure, use 100MVA as system base, and 230 kV as base voltage along the transmission line. For the same system in the figure, build the Y-bus matrix without the Load. 1. What is the element Y11? Provide the susceptance value 2. What is the element Y22? Provide the susceptance value
The figure below shows the one-line diagram of a simple three-bus power system withgeneration at bus 1. The voltage at bus 1 is V1 = 1.0∠0°per unit. The scheduledloads on buses 2 and 3 are marked on the diagram. Line impedances are marked inper unit on a 100 MVA base.(a) Using Gauss-Seidel method and initial estimates of ?2(0) = 1.0 + ?0, ?3(0) = 1.0 + ?0, determine V2and V3. Perform two iterations.(b) If after several iterations the bus voltages converge to?2 = 0.90 − ?0.10 pu?3 = 0.95 − ?0.05 pudetermine the line flows and line losses and the slack bus real and reactive power.
For the system in Figure 4 with given generation and load dispatch determine the voltages after two itterations of Gauss-Seidel method. Assume the initial voltage to be 1.01 at angle of 0◦ pu at bus 1, 1.015 at angle of 0◦ pu at bus 2, and 1.0 at angle of 0◦ pu at bus 3. All line impedances are in per unit on a common base, and charging is neglected. Take base power of 100 MVA.
PROBLEMS i istic such that rated armay, short.circuit characteristic 5 « ; aa'gﬂ?;ciunﬁ e ion. Rated voltaEo on the sitgap line o ts-unit excitation 1s reduted o, su pf lagging? tor is 80% leading. 51, A synchronous gei current is obtained by obtained by 1.25 per-unit excitat = load at rated voltage, rated VA, and 807 52, Repeat Prob, 5-1 for the case where the foad pover fac 5.3, A synchronous generator has the following rating? 180-KVA, 440-V, 300-rpm, 60-Hz, three-Phase: r~0 and x —02960Q Theuit-sap line it described by the equation £ = 1117, RIS = e b Y-connection, expressed per phase. The short. the field current needed