QUESTION 5 The inventor claims that a power cycle operates between hot and cold reservoirs at 1200 K and 400 K, respectively, with Q₁=600 kW.Q=0 kW. Calculate the rate of entropy production for this cycle in kW/K. Enter the answer without units, but with a sign if applicable. QUESTION 6 This cycle operates O irreversibly O reversibly O impossibly.

QUESTION 5 The inventor claims that a power cycle operates between hot and cold reservoirs at 1200 K and 400 K, respectively, with Q₁=600 kW.Q=0 kW. Calculate the rate of entropy production for this cycle in kW/K. Enter the answer without units, but with a sign if applicable. QUESTION 6 This cycle operates O irreversibly O reversibly O impossibly.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 2.00 mol sample of an ideal diatomic gas is taken through a reversible cycle A → B → C → A as shown in the figure below. Process A → B is isothermal expansion. For the cycle, calculate: a) the work done by the gas, b) the heat energy added to the gas, c) the heat energy exhausted by the gas, d) the thermal efficiency, e) the change in entropy of the gas. f) Determine the efficiency of a Carnot engine operating between the same temperature extremes, R = 8.314 J/mol K Data at vertices for the above PV diagram are as follow: PA = 5.00 x 105 Pa, VA = 1.00 x 10 -2 m3, PB = 1.25 x 105 Pa, VB = 4.00 x 10 -2 m3 PC = 1.25 x 105 Pa, VC = 1.00 x 10 -2 m3
Find the entropy production and determine if the cycle operates irreverisbly, reverisbly, or impossibly. A refrigeration cycle operates between the freezer compartment at 268K and the ambient air at 295K. The rate of heat transfer from the freezer compartment is 8000 kJ/h and the power input for the cycle is 3200 kJ/h. Determine the entropy production for this cycle in kJ/K·h (do not convert h to s). Enter the answer without units, but with a minus sign if applicable. This cycle operates irreversibly reversibly impossibly.
An isentropic turbine has air entering the turbine where h = 1855.50 kJ/kg, p = 4.0 MPa and so = 3.58335 kJ/(kg · K). If the air leaves the turbine at a temperature of 397 °C, what is the final pressure and the specific work output of the turbine with variable specific heats [R = 0.287 kJ/(kg•K)]?
1. An engine from a quarry vehicle used in the Build a Beach program of DEMR has a power requirement of 560 kW. Per hour of its operation, it ejects 234 MJ into its surroundings at 50 °C. If it behaves like a Carnot engine, answer the questions below. A. How much work (MJ) is done by the engine per hour of operation? B. What is the efficiency (%) of the engine?C. What is the temperature (°C) of the hot reservoir? 2. Determine the entropy change (kJ/K) associated to the conversion of 10 kg of ice at -11 °C to steam at 121 °C. 3. Anna and Beth are using another rare metal, the nth metal (c = 0.600 J/g-℃), to build the 5-kg cuirass of their design. Initially, the metal is at 2250 K. It is then submerged to 10 kg of water at 15 °C. If the remaining liquid water after submerging the metal is 8.5 kg, solve for the net entropy change (kJ/K) of the system.
A turboprop engine consists of a diffuser, compressor, combustor, turbine, and nozzle. The turbine drives a propeller as well as the compressor, delivering a net power of 1 MW to the propeller. Air enters the diffuser at 8000 m altitude (Ta = 236K, pa = 36 kPa) with a velocity of 550 km/h, and decelerates essentially to zero velocity. The compressor pressure ratio is 5.3 and the compressor has an isentropic efficiency of 83%. The turbine inlet temperature is 1360 K, and its isentropic efficiency is 86%. The turbine exit pressure is 10 kPa higher than the ambient pressure at that altitude. Flow through the diffuser and nozzle is isentropic. Neglect kinetic energy except at the diffuser inlet and the nozzle exit. Using an air-standard analysis, determine: a) The mass and volumetric flow rates entering the diffuser, in kg/s and m3/s, respectively.b) The rate of heat addition to the combustor, in MW.c) The velocity at the nozzle exit, in m/s.
Based on a gas turbine with superheat and intercooling, determine: 1) The thermal efficiency (ƞterm), in %. Use the expression ƞterm= 1 –(qL/ qH)2) How does gas turbine intercooling influence thermal efficiency?3) How and why? It is said that the gas turbine cycle with intercooling, reheating and regeneration is close to the Ericsson cycle.
Consider the following quantities for a reversible Carnot cycle: Step 1 q = 850 J, w = -434 J Step 2 q = 0 , w = -115 J Step 3 w = 72 J Step 4 q = 0, w = +115 J a) Calculate the efficiency of the cycle. b) If the initial temperature in step 1 is 25°C, what is the temperature at the end of step 2. c) If the number of moles of ideal gas involved in the cycle is 0.1 mol; calculate ΔH for step 4
A turboprop engine consists of a diffuser, compressor, combustor, turbine, and nozzle. The turbine drives a propeller as well as the compressor. Air enters the diffuser with a volumetric flow rate of 83.7 m3/s at 40 kPa, 240 K, and a velocity of 180 m/s, and decelerates essentially to zero velocity. The compressor pressure ratio is 10 and the compressor has an isentropic efficiency of 85 %. The turbine inlet temperature is 1,140 K, and its isentropic efficiency is 85 %. The turbine exit pressure is 50 kPa. Flow through the diffuser and nozzle is isentropic. Sketch the process on the T-s diagram and using an air-standard analysis, determine, the power delivered to the propeller, in MWt the velocity at the nozzle exit, in m/s. Neglect kinetic energy except at the diffuser inlet and the nozzle exit.
17-Initial pressure of 900 kPa and 80°C in a piston-cylinder assemblyThere is 734 grams of refrigerant-134a (R-134a) at temperature.The refrigerant is then at constant pressure up to a temperature of 26°C.is cooled. What is the entropy change? A) – 0,7284 kJ/K B) – 0,4315 kJ/K C) – 0,5879 kJ/K D) – 0,4111 kJ/K E) – 0,5346 kJ/K
At the beginning of a cycle using air, the pressure, volume and temperature are 550 kN/m 2 , 0.025 m 3 and 15°C, respectively. The air is heatedat constant pressure until the temperature is 204°C. It is then expanded adiabatically until the temperature becomes 120°C. The air is cooled atconstant volume to a temperature of 15°C then restored to its original volume by isothermal compression. (a) Draw the pressure volume and temperature entropy diagram.(b) Determine for the cycle, the heat received,(c) the work done,(d) the thermal efficiency, Take Cp =1.00 kJ/kgK, Cp /Cv =1.4
Fast ,Do not hold. Two heat engines receive heat from a source at temperature of 550◦C. Heat engine "A" receives 200 kJ of heat and rejects the waste heat to a sink at 180◦C. Heat engine "B" receives 180 kJ of heat and rejects the waste heat to a sink at 120◦C.(a) Caclualte the generated entropy, Sgen, in both processes.(b) Based on your answer in part (a), identify the heat transfer that is more irreversible.
Brayton cicle Based on a gas turbine with superheat and intercooling, determine: 1) The thermal efficiency (ƞterm), in %. Use the expression ƞterm= 1 –(qL/ qH)2) How does gas turbine intercooling influence thermal efficiency?3) How and why? It is said that the gas turbine cycle with intercooling, reheating and regeneration is close to the Ericsson cycle.