Question 6 Using V = 4 mV, and given the voltage across an inductor L = 6 mH as shown in Fig. P6.25, determine the equation of current as a function of time across the inductor during the time Oms <= t <= 1 ms. Assuming the solution looks like it (t) = Xt² + C, what is the value of X? For your answer, just put the value of X in Amperes/s² (there should only be a number in your answer). v(1) (mv) V 0 Figure P6.25 Notes on entering solution: . Enter your solution in Amps/s² • Pay attention to the interval • Enter your solution to 2 decimal points Only put the number before the t2, ex. 2001² + 1 is entered as 200 (ms) • Pay attention to signs . Do not include units in your answer .ex. 5A/s² is entered as 5.00

Question 6 Using V = 4 mV, and given the voltage across an inductor L = 6 mH as shown in Fig. P6.25, determine the equation of current as a function of time across the inductor during the time Oms <= t <= 1 ms. Assuming the solution looks like it (t) = Xt² + C, what is the value of X? For your answer, just put the value of X in Amperes/s² (there should only be a number in your answer). v(1) (mv) V 0 Figure P6.25 Notes on entering solution: . Enter your solution in Amps/s² • Pay attention to the interval • Enter your solution to 2 decimal points Only put the number before the t2, ex. 2001² + 1 is entered as 200 (ms) • Pay attention to signs . Do not include units in your answer .ex. 5A/s² is entered as 5.00

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The voltage at the terminals of the 200 μH inductor in Fig. P6.2(a) is shown in Fig. P6.2(b). The inductor current i is known to be zero for t≤0. 1. Derive the expressions for i for t≥0. 2. Sketch i versus t for 0≤t≤∞.
The current in and the voltage across a 10H inductor are known to be zero for t 스 0. Ihe voltage across the inductor is given by the graph in Fig. P6.9 for t 2 0.
The initial voltage on the 0.5 μF capacitor shown in Fig. P6.19(a) is −20 V. The capacitor current has the waveform shown in Fig. P6.19(b). 1. How much energy, in microjoules, is stored in the capacitor at t=500 μs? 2. Repeat (a) for t=∞.
The voltage at the terminals of the 750 uH inductor in Fig. P6.7 (a) is shown in Fig. P6.7 (b). The inductor i is known to be zero for t <0. current a) Derive the expressions for i for t >= 0. b) Sketch i versus t for 0 =<t=< unlimited
. If a 4μF capacitor is connected to a constant current source, therefore its current is given in the equation ic(t)=10mA. Determine the voltage, power and energy at 2ms.
A current of 2 uA is discharged on a capacitor with a plate area of 100 cm² and a capacitance of 1x10-^7F at t=0, and find the displacement current intensity (uA) between the plates at t=0.
The current, i, through a capacitor depends on time, t, and is given by where V is the voltage across the capacitor and C is the capacitance of the capacitor. Derive an integral expression, in terms of i and C, for the voltage V A capacitor of capacitance 3 x 10-2 F has a current i(t) through it where Determine the function for the voltage across the capacitor The change in current through a semiconductor diode depends on the applied voltage and is given by: where: V = applied voltage (V) I = diode current (A) Is = reverse saturation current (A) T = temperature (K) q and k are constants Given that when V = 0, I = 0 find an expression for the current with voltage. The reverse saturation current for a particular diode is 1 x 10-9 A and at 300 K 40. Write down an expression for the current and find the value of the current when V = 0.35 volts.
2. A parallel plate capacitor with a plate area of 0.13 square meters separated by 1 mm is charged to 9 Volts by a battery, which is then disconnected. The plate separation is then increased to 40 mm.A. Using the expression for the capacitance of a parallel plate capacitor, what do you expect the new potential difference across the plates to be after the increase?B. Suppose you measure the potential difference across the plates after the separation and find it to be 30 V (this should be very different from what you found in part A). This unexpected result can be explained by the effects of “stray capacitance” with nearby objects. Assuming that the stray capacitance can be modeled as a capacitor connected in parallel with the parallel plate capacitor, find the value of this stray capacitance.
Assignment No. 5 Inductance, Capacitance, and Mutual Inductance a.) Find the voltage across the inductor for t > 0. (Assume the passive signconvention.)b.) Find the power (in microwatts) at the terminals of the inductor when t = 5 ms.c.) Is the inductor absorbing or delivering power at 5 ms?d.) Find the energy (in microjoules) stored in the inductor at 5 ms.e.) Find the maximum energy 9in microjoules) stored in the inductor and the time(in milliseconds) when it occurs.
Inductance, Capacitance, and Mutual Inductance d.) Find the energy (in microjoules) stored in the inductor at 5 ms.e.) Find the maximum energy 9in microjoules) stored in the inductor and the time(in milliseconds) when it occurs.D and E only. Thank youuu
present a derivation for the expressions of the energy stored in a capacitor and inductor
A 3.0 MΩ resistor and a 1.0 μF capacitor are connected in series with an ideal battery that has an emf E = 5.0 V. After 1.0 s after the initial connection is made, find the rate at which(a) the charge on the capacitor is increasing (inC/s),(b) energy is being stored in the capacitor (inJ/s),(c) thermal energy is appearing in the resistor (inJ/s), and (d) energy is being delivered by the battery (inJ/s).