QUESTION 7: A Wilson current-source circuit is shown in the following figure.Assume the reference current (IREF) is 0.23 mA and assume the transistor parameters of VBE(on) = 0.7 V, ß = 88,and VA = 123 V.Calculate the output resistance, Ro , looking into the collector of Q3.Io (mA)Ro (M2)|Format : 0.9962Format : 46.7946V+Ic3 = loIREF (+Q3IB3'E3|lc2IB1B2

Wilson current-source circuit It is a three-terminal circuit model of modified configuration, which…

QUESTION 7: A Wilson current-source circuit is shown in the following figure. Assume the reference current (IREF) is 0.23 mA and assume the transistor parameters of VBE(on) = 0.7 V, ß = 88 and V4 = 123 V. Calculate the output resistance, Ro , looking into the collector of Q3- Io (mA) RO (ΜΩ ) Format : 0.9962 Format : 46.7946 V+ Ic3 = lo IREF (+ IB3 E3 Qi IBI B2

QUESTION 7: A Wilson current-source circuit is shown in the following figure. Assume the reference current (IREF) is 0.23 mA and assume the transistor parameters of VBE(on) = 0.7 V, ß = 88 and V4 = 123 V. Calculate the output resistance, Ro , looking into the collector of Q3- Io (mA) RO (ΜΩ ) Format : 0.9962 Format : 46.7946 V+ Ic3 = lo IREF (+ IB3 E3 Qi IBI B2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Design a common emitter amplifier for a Vout of+-6.3V. Vcc is set to 9V. At x=1, Av=12.6 V/V and the dynamic range from 6.3V to -6.3V. Rout must be less than 100 ohms and Rin must be higher than 100 kohms
Instruction/s: 1. Draw, Illustrate and label your schematic diagram before solving the problem. 4.) Given a Voltage -divider biased transistor circuit .Assume Beta DC is 100, ,Voltage at Base-emitter junction is 0.7v ,voltage at common collector is +15v, resistor RB1 is 10k ohms, resistor RB2 is 6k ohms, collector resistor is 1.5k ohms ,emitter resistor is 560 ohms. Determine base current ,collector current and voltage collector-emitter junction. These might help as a guide in answering the problem..
question from book ELECTRONIC CIRCUIT DESIGN : Question No. 2 Analyze the circuit in figure 2 to find IDQ, VGSQ and VDS. As given in circuit, the IDSS is8mA but a customer requires current more than this IDSS. Suggest a change in the circuit resistorswithout changing the MOSFET. Prove your suggested circuit by doing load line analysis. Is the Q pointin the new circuit is located at correct location?
Since Vcc = 12 V, Vin = 690 mV, RB = 780 kΩ, RC1 = 27.9 Ω, RC2 = 25.4 Ω, RE = 470 Ω, RL = 47 Ω and β1 = β2 = 100 in the circuit in the figure Find the current (IL) flowing through RL? NOTE-1: VBE1 = VBE2 = 0.7 V will be taken. NOTE-2: Output impedances of transistors (r0) will be neglected.
What is the output voltage for the circuit diagram given below? For VGS(on) = 4.5V , ID(on)=75mA , RDS(on) = 6ohm
Draw, Illustrate and label your schematic diagram before solving the problem. 3) Given an Emitter-Stabilize Biased transistor circuit with beta DC is 250,Base resistor is 150 ohms, collector resistor is 1.5k ohms ,emitter resistor is 500 ohms ,emitter voltage supply is -5v and Voltage at common collector is +28V,Voltage at Base-emitter junction is 0.7v,. Determine Base current, Collector current and Voltage at collector-emitter junction.
For the given Common Emitter NPN Amplifier, the transistor made of Germanium diodes, βDC=80,VCC = 16 volts, R1= 62 KΩ, R2= 9.1 KΩ, RC= 3.9 KΩ, RE= 0.68 KΩ. a) Name the type of biasing used in the above circuit? b) Find VE? c) Find VCE? d) Find VC? e) What is the name of the capacitors C1, C3and C2?
An amplification factor of B = 100 can be applied for both transistors. Additionally, the two transistors have the same UBE of 0.8 V. In saturation, UCE is 0.2 V for both transistors. Assuming an overload factor of b = 5 and a constant UI of 5 V, calculate the current IC1, IB1 and the resistance RV
A Bipolar junction Transistor with curreat amplification factor being 100, Input Base current is 50μA. Collector voltage is 10 V and biasing voltage being +20 V. Find followings a. Collector current b. Resistance (R1) c. Collector voltage , Emitter voltage , Base Voltage & Collector-Emitter Voltage.
Design a Single-Stage Common Emitter Class A Amplifier Specifications:Voltage Divider Bias Circuit Supply: Any value from 10Vdc to 24VdcLoad: 1kΩVoltage Gain: Any value from 80 to 400Lower Cutoff Frequency: 100 HzSinusoidal source (zero internal resistance): 50mVp-pTransistor: Si, β = 75 • Base-Collector capacitance = 8pF • Base-Emitter Capacitance = 25pF a) compute for the biasing resistances.b) determine the dc transistor terminal voltages and transistor currents.
In the circuit in the figure, VGSQ = 6.8 V, IDQ = 2.4 mA, VGS(Th) = 3.3 V, k = 0.4x10-3 A/V2, RD = 5.6 kΩ, RF = 2.2 MΩ and rd = 25 kΩ. Accordingly, when a RL = 23.6 kΩ load is connected to the output of the circuit, what will be the voltage gain of the circuit? NOTE: MOSFET output resistance must be taken into account in rd calculations.
Consider the circuit. The transistor has a parameter β that varies between 50 and 200. The operation of the circuit and the electrical variables at the end points must be known. end points. Calculate the following for β = 50 and β = 200. a) lE, VE and VB (DC analysis). b) The input resistance Rin (small signal analysis). c) Voltage gain V0/ Vsig (Small Signal Analysis