Answered: Question 9 The combined losses occuring…

Question 9 The combined losses occuring in armature and field circuit of a DC motor is known as the rotational losses O True O False

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter43: About Dc Motors

Section: Chapter Questions

Problem 1SQ

See similar textbooks

Related questions

Q: Does a DC motor have to be turning in order for it to develop torque? a) yes b) no Most DC motor…

A: The Dc motor is electrical machinery that converts electrical and mechanical energy

Q: 8. A shunt motor is running at 1200 rpm for a load which requires an armature current of 50 Amp from…

A: Given Speed N=1200 rpm Armature current Ia=50 A Terminal voltage V=230 V No-load armature current…

Q: The direction of rotation of Series DC motor can be reversed by interchanging terminal(s). 1) Field…

A: The change in the flow of current divert the direction of the spinning force, due to this the…

Q: Indicate whether the following statement are true or false * True False Dc shunt motor is best…

A: In this question , we will see why shunt motors provide low starting torque.. Note:- I will answer…

Q: rated load, a shunt motor draws an armature current of 50A from a 230V dc mains while running at…

A: Please refer the attached images for the complete answer..

Q: torque available at the shaft of DC series motor is less than the torque developed in the armature…

A: When the armature power is applied to rotate the shaft of the DC series motor, some power loss…

Q: 1-D.C. shunt motor maintains a more constant speed under varying load. (True or False) 2-Dc shunt…

A: 1-D.C. shunt motor maintains a more constant speed under varying load. 2-Dc shunt motor is best…

Q: A 250 V, DC shunt motor has shunt field resistance of 250 ohm and an armature resistance of 0.25…

Q: We have a shunt DC Generator. Its armature resistance and shunt excitation resistance are 0,3 Ω and…

Q: b) Draw the speed control block diagram of the DC motor, which can be controlled with armature…

A: Ac speed control motors- Constructio motor- the construction of the single phase and three-phase…

Q: A 240 V, 4 -pole shunt motor has an armature resistance Of 0.42 and a field resistance of 2402. When…

A: Supply voltage (V) = 240 V No. of poles (P) = 4 Armature resistance (Ra) = 0.4 Ω Field resistance…

Q: 1-The main disadvantage of Rheostatic control method of a dc shunt motor, that the speed up to zero…

A: In this question , some statements are given related to dc machines , we have to find out that they…

Q: The field winding resistance of DC shunt motor compared to its armature resistance is O Very high O…

A: DC Motor: DC Motor is an electromechanical device which converts electrical energy to mechanical…

Q: A compound motor has 1200 turns on the shunt winding and 25 turns on the series winding, per pole.…

Q: 3. A 4 pole, 250 dc shunt motor has a lap connected armature with 960 conductors. The flux per pole…

A: The solution can be achieved as follows.

Q: If the voltage applied across the armature of a DC shunt motor is increased by 5% keeping its load…

A: generated emf in armature E = flux ×speed×no. of conductors60 ×no. of polesno. of parallel paths…

Q: 1.) A certain 5.5 kW, 125-V DC long shunt compound generator was operated as a shunt generator motor…

A: Given: Armature resistance, Ra=0.2 ΩSeries field resistance, Rse=.25 ΩShunt field resistance, Rsh=25…

Q: A 250-V shunt motor runs at 1500rpm at no-load and takes 8A. The total armature and shunt field…

A: To calculate tha speed of shunt motor when it is loaded Assuming flux is constant

Q: the relation between armature and field currents in a series connected DC motor is O It = If + la O…

Q: A 250 volt DC shunt motor has armature resistance of 0.25 ohm on load it takes an armature current…

A: In this answer we will find the new speed of the motor using the formulae as explained below.

Q: 19.a. The magnets that are used in the field of a quality DC PM motor are made from A. rare-earth…

A: Operation of permanent magnet DC motor depends on the flux and flux is produced by magnets. So the…

Q: Problem 3 A dc shunt motor runs at 900 rpm from a 400V supply when taking an armature current of…

Q: A 250-volt resistance DC generator has an armature of 0.10, shunt field resistance is 500, and…

A: Given a DC long shunt generator with, Terminal voltage, Vt=250 V. Armature resistance, Ra=0.1 Ω.…

Q: a) In the experiment of performance study of three-phase wound rotor induction motor, what are the…

A: 1)Upon adding external resistance on the, a)Motor slip, The speed of the motor decreases. b)Motor…

Q: d) Explain the difference between locked motor torque and the pull up torque of an induction motor.…

A: Locked rotor torque : The torque generated by an electrical motor, when it begins at rest or zero…

Q: The armature winding resistance of a 200 Volt 4-pole DC motor is 2 ohms. Under full load, the…

A: Given armature winding Resistance R=2 ohms Given Terminal voltage V=200 no of conductors Z=360 no…

Q: The armature resistance of 220V shunt DC motor is 0.4 takes load armature of 2A and run at 1350…

A: Given, A DC shunt motor having, Terminal voltage, V = 220 V Armature resistance, Ra=0.4 Ω Case (i)…

Q: A 250 Volts shunt motor has an armature resistance of 0.5 ohm and a field resistance of 250 ohms.…

Q: Sketch armature current (y-axis) - torque (x-axis) characteristics of compound DC motor for three…

A: A compound DC motor connects the armature and fields windings in a shunt and a series combination to…

Q: Problem 5 Calculate the torque in N-m developed by a 440V dc motor having an armature resistance…

Q: The characteristic (Speed versus armature current) of a dc shunt motor is known as the electrical…

A: Electrical characteristics are the drawn between armature current on X axis and speed on Y axis.

Q: A 20 h.p., 250 V shunt motor has an armature circuit resistance (including brushes nd interpoles) of…

A: Back emf = terminal voltage-voltage drop in armature resistance. Take the ratio of back emfs to find…

Q: A 240V dc shunt motor has armature and field resistances 0.2 W and 320 W respectively. The motor…

A: Back emf in dc motor is directly proportional to product field flux and armature speed. back emf =…

Q: a)Explain the speed control methods of direct current motor. b)Compare linear current series motor,…

A: For a) Speed control of a DC motor is either done manually by the operator or by employing an…

Q: 14) the difference between internal generated voltage and output voltage in synchronous generator…

A: As per guidelines given to us,we can only provide the solution of first question in multiple type of…

Q: Compensating winding does not solve the problem of armature reaction completely then why do use in…

A: Compensating winding is used in DC motor for eliminating the problems of armature reaction and…

Q: The armature resistance of a shunt motor fed from a 220 Volt DC source is 5 ohms and the resistance…

A: According to question: Case1) When only field winding of resistance 'R' is present:

Q: 6. The major failure area of a typical wound-field and wound-armature DC motor is A. brush wear and…

A: In DC machine, major problems are due to brushes.

Q: 3. A 4 pole, 250 dc shunt motor has a lap connected armature with 960 conductors. The flux per pole…

A: In this question, Torque develop by the armature in N-m. Torque T= power/(2πN/60) N-m If the…

Q: A 220 V, shunt DC motor takes an armature current of 18 A. The armature resistance is 0.2 0.…

A: At No loadNNL=975VL=220Em0=220-Ia0×RaKϕNNL=220-1×0.2KϕNNL=219.8 1 At loaded condition…

Q: - The speed of dc shunt motor can be varied by: a) The voltage V applied to armature. b) The…

A: If we change applied voltage to the armature of DC shunt motor it will directly reflect on the speed…

Q: > The armature winding is the main current-carrying winding in which the electromotive force or…

A: The armature winding is the main current carrying winding in which the electromotive force or…

Q: The armature resistance of a shunt motor fed from a 220 Volt DC source is 5 ohms and the resistance…

A: Explanation: Given that, Ia = 4 A, Ra = 5 ohm, Vt = 220 volt, Tload = 7 Nm

Q: Make a sketch to show the speed torque characteristics of a shunt and compound motor

A: for the case of the shunt motor as we increase the torque the speed of the shunt motor decreases and…

Q: Q4 : A 3 phase, 50 Hz, 6 pole wound rotor induction machine has the following per phase parameters…

A: The solution is given below

Q: a) If the torque pulled from the shaft is doubled while the asynchronous motor is working in the…

A: As per our policy, i have to attain only one question. Solution a)- In the asynchronous motor's…

Q: The armature of a 8 pole d.c. shunt motor has a lap connected armature winding with 1000 conductors…

A: Consider the given values, The No load flux is given as, ϕNL=10 mWb. Due to armature reaction, the…

Q: A 250 V shunt motor on no-load runs at 1000 r.p.m. and takes 5 A. The total armature and shunt field…

Q: Report 1- Sketch speed (y-axis) torque (x-axis) characteristics of compound DC motor for three…

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Concept explainers

Synchronous Motor

The synchronous motor is an AC electric type motor where at a steady-state the shaft rotation is synchronized with the supply current variable-frequency. To an integral number of AC cycles, the rotation period is exactly equal. The stator of the motor in the synchronous motor contains multi-phase AC electromagnets due to which a magnetic field is created that rotates in time with the oscillation of the line current. The rotor contains a permanent magnet and the rotor rotates in synchronization with the stator field at the same rate and provides the second synchronized magnetic field which is rotating in nature as a result. When the synchronous motor is supplied with independently excited multi-phase AC electromagnets on both the rotor and the stator, it is termed as a doubly-fed machine. The most widely used AC-type motors are the synchronous AC motor and the induction AC motors.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 250-V shunt motor runs at 1500rpm at no-load and takes 8A. The total armature and shunt field resistance are respectively 0.12 ohm and 250 ohm. Calculate the speed loaded and taking 50A. assume the flux to be constant.
(TRUE OR FALSE) - Shunt motor should not be started on no-load. - Field copper loss is likely to have highest proportion at rated load ofthe DC generator. - In a DC generator, the iron losses mainly take place in the commutator. - Energy conversion of DC generator is based on the principle ofproduction of dynamically terminal voltage. - Increasing the speed of DC motor, the back emf will decrease but theline current falls. - The current drawn by the armature of DC motor is directly proportionalto torque. - Lenz’s law rule is used to determine the direction of rotation of dcmachines. - Compound dc motor at no-load it regulates highest speed. - The direction of this force is perpendicular to both the wire and themagnetic field in DC motor. - The direction of DC motor induced emf is such that the same of thearmature current.
An 8-Pole, simplex lap wound, shunt generator has 800conductors and a flux per pole of 0.025Wb and running at 1200rpm. The armature and shunt field resistances are 0.25Ω and 120Ω respectively. If the armature voltage drop is equal to 10V, what is the load current (in Amp)? use two decimal places if the answer is not exact and do not include the unit anymore.
11. Armature copper loss of DC motor is constant with the load. Select one: True False
Q4. 1- What is the main function of a diverter used in series wound DC motor? 2- What is the main difference between (iron and friction losses) and copper (Cu) losses in DC generators?
electrical machines (((How does an asynchronous motor behave when there is a load?))) this is what i want read the equestion down explain by drawing an experiment connection diagram. the loaded experiment of induction motor (asynchronous motor) after that Briefly explain the loaded operating characteristic by drawing.
electrical machines (How does an asynchronous motor behave when there is a load?) explain by drawing an experiment connection diagram. the loaded experiment of induction motor (asynchronous motor) after that Briefly explain the loaded operating characteristic by drawing.
The armature, series field and shunt field resistances of 125 kW, 250 V long shunt cummulative compound DC generator are 0.025 ohms, 0.01 ohms and 30 ohms respectively. If stray power loss at rated load is 5 kW, determine the power in the armature field
3-phase 3730W, 220V, 8 poles and 50 Hz asynchronous motor operates at full load with a slip of 0.025. The sum of the rotational losses including friction + windage losses and other (stray load) losses is 5% of the output power. Find the induced (electromagnetic) moment at full load.
A 120V dc shunt motor has an armature resistance of 0.25Ω is drawing 50A. If a fixed loss of 200W was measured and neglecting the shunt field, what is the copper loss (in watts)? (meaning no shunt field used)
Thanks in advance. Please answer this question by explaining the each step and reasoning why u used that method or formula. By the way, this question is related to electromechanical energy conversion lecture. The no-load and locked-rotor test results of a three-phase 10 HP, 220 V, 60 Hz, 6 poles star connected induction motor are; The no-load test: VNL=220 V, PNL=340 W, INL=6.2 A The locked-rotor test: VSC=54 V, PSC =430 W, ISC =15.2 A The voltage across the stator windings is 2 V when nominal DC current flows through it. Coefficient for DC resistance is 1,25. a) Calculate the equivalent circuit parameters and draw the complete single-phase equivalent circuit of the induction motor. b) Calculate efficiency of the motor for s=0.06 by using the approximate equivalent circuit (RFe core resistance is not ignored). c) Shaft torque for s=0,06 d) Slip value at the maximum (breakdown) torque, e) Maximum (breakdown) torque of the induction motor. f) Speed of the motor at maximum torque point.…
A Short shunt compound generator delivers a load current of (16)A at 400V. Armature resistance 0.08 ohms, Series field resistance is 0.6ohms and the shunt field resistance is 200+ 16 ohms. Calculate the induced EMF and the armature current. Allow 1.5V per brush for contact drop Calculate the efficiency. Neglect the core and mechanical loss