Question 9 The Nusselt number for fully developed laminar flow in a pipe first increases and then decreases. is a fixed number and remains constant. depends on the existing Reynolds number and Prandtl number. depends on pipe diameter.

Question 9 The Nusselt number for fully developed laminar flow in a pipe first increases and then decreases. is a fixed number and remains constant. depends on the existing Reynolds number and Prandtl number. depends on pipe diameter.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.4P: 5.4 Evaluate the Stanton number for flow over a tube from the following data: , , , , .

See similar textbooks

Related questions

Q: A reheat cycle with two stages of reheating is executed, with steam expanding initially from 90 bar…

Q: What horsepower is required to isothermally compress 800 ft3of air per minute from 14.7 psia to 120…

Q: A solid cylindrical bar conducts heat at a rate of 25 W from a hot to a cold reservoir under steady…

Q: 2.77 A steel rod 3 ft long with a cross-sectional area of 0.3 in.² is stretched between two fixed…

Q: 2. Water exits out of four nozzles below the platform as shown at 15m/s. If the man, the platform,…

Q: What is compound indexing?

A: Soln:- Compound indexing :- Compound indexing is the operation of obtaining a desired spindle speed…

Q: 1. The intensity of the shear stress distribution acting over the cross sectional area needs to be…

Q: A vertical semi-circular area of radius r is submerged in a liquid with its diameter in the liquid…

Q: Given the following data: Follower type = roller follower, off-set to the right by 5mm; lift 30mm;…

A: Given:- Off-set, x=5 mm,Base circle radius,rbase=25 mm,Roller radius, rr=5 mm,Lift,h=30 mm,Angle of…

Q: Problem 2: A circular rod tapers in diameter from 50 mm from one end to 20 mmon theother end for a…

Q: a) Outline the three main approaches to maintenance b) can be used to measure the condition of a…

Q: A steel component is subjected to alternate cyclical loading. The steel follows Basquin's law for…

A: given; minimum stress(σmin)=-213MPamaximum stress(σmax)=213MPa

Q: 1. d²y + 2 -3y = 0 dx2 2. (D² +2D)y = 0 xp %3D %3D Find the general solution of the following:

A: Find the general solution of the differential equations.

Q: Problem (5). The internal and external diameters of the centrifugal pump are 200 mm and 400 mm…

Q: The figure (not drawn to scale) shows a metallic cylindrical column submitted to a combined load:…

Q: A rigid lever arm is supported by a pin at E, and wire cables at A and C. Force P = 15.00 kN acts…

Q: In the truss system shown, Calculate all internal forces in 3 m each member by method of joints.…

Q: The task is to to transfer the fluid from the source towards the tank (TANK A) lying on an elevated…

Q: The figure (not drawn to scale) shows a metallic cylindrical column submitted to a combined load:…

Q: B1. A snowboarder rides over a jump (see the sketch below), where the launch ramp is at an angle of…

A: (1) Consider the path from take off point to start point of landing. Apply kinematic equation in…

Q: When a tree branch bends, it can be assumed that acts as a spring, i.e there is a restoring force…

A: Given : To find : mass of the monkeys

Q: A solid homogeneous truss tie-rod has a diameter of 9.52 mm and an original length of 1.75 m…

Q: Find the distance in (inches) of the shafts if th

A: TO find Distance of shafts

Q: A reservoir like the one shown has SAE10 oil at 20 C and is connected to a capillary tube for…

A: Neglect major and minor losses

Q: What are the four major accessories of a Rankine Cycle? Define each.

A: Rankine cycle is the cycle of 4 process including 4 major accessories Boiler, Turbine, Condenser…

Q: b) The bore diameter of each cylinder in a six-cylinder four-stroke internal combustion engine is 32…

A: Find Mean effective pressure Indicated Power

Q: Answer all subparts: Water at 25 °C flows through an inclined plane. a. Assuming steady laminar…

Q: Consider the system below. Calculate the kinetic energy of this system. Assume that pulley otates…

A: Drr

Q: The wheelbarrow and its contents have a mass of 60 kg with a centre of mass at G. Determine the…

Q: D5. A converging-diverging nozzle operates with air and subsonic flow at the inlet and supersonic…

A: Find , M2 , P2 at exit

Q: Saturated vapor of Refrigerant 134a contained in in a piston-cylinder device undergoes an isothermal…

Q: starts to slide in a way that the contact point at A moves to the left while the contact point at B…

Q: Determine the chain speed in meter/sec of an rc 80 on a 21-tooth sprocket turning at 600 rpm.

A: find the speed of chain.

Q: Each cylinder in a four-cylinder car engine has a bore diameter of 63.53 mm and the stroke for each…

Q: coefficient of kinetic friction is f = 0.2 between the surface and A, determine the following: the…

Q: 2. For the preceding problem, using actuator disc theory, determine the axial flow induction factor,…

Q: The bodies shown are moving to the right with the same velocities indicated. If e=0.75, determine…

Q: A rotating cylinder viscometer is used to measure the viscosity of fluids. The viscometer we are…

A: Answer: The viscosity of the fluid: 0.00375 N•sec/m2 ( 3.75 centi-poise).

Q: b) The bore diameter of each cylinder in a six-cylinder four-stroke internal combustion engine is 32…

Q: At 3.0 bar pressure and 25.0 degrees Celsius, it is thought to be ideal for a 1.5dm3 hydrogen gas.…

Q: Resolving power of an spectroscopic instrument is increased when...

A: Resolving the power of spectroscopic as the minimum wavenumber, frequency or the wavelength which is…

Q: Calculate the absolute pressure in kPa at a depth of 11 m below the oil's free surface, with a…

Q: 2. Find the are length of the curve from x=2 to x-3

Q: II KN m SKN m 3 kN m 3 kN m 75 mm 85 mm 70 mm 2 m 2 m 2 m FIGURE P12-6 The "new" magnitude of the…

A: First balance the existing torques , if there is requirement of new torque at B, then it will be…

Q: An equilateral triangular plate of 3 m side is immersed vertically in such a way that the apex is in…

A: We have a 3 m side equilateral triangular plate immersed vertically with the apex in the downward…

Q: 2.75 A steel rod is stretched between two wals. At 20°C, the tensile force in the rod is 5000 N. If…

A: The minimum allowable diameter of the rod is 13.225 mm.

Q: 中16 60 28 45 30 し16. 互 8. 115 40 09 16 40.

Q: llower type roller follower, off-set to the right by 5mm; lift = 30mm; base c dius = 25mm; roller…

Q: A block with weight (W=75lbs) can move vertically between two smooth walls. It is held by a rope…

Concept explainers

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

For water flowing in a pipe of 8 inches diameter at 65 oC and 0.01 ft3/s, what will be the entry length (Le) needed for water flow to be described as fully developed flow? What does that tell you about the length of the tube you should select in your design?
For fully developed laminar pipe flow, if the diameter of the pipe is decreased by a factor of 3 whereas the length of pipe and flow rate is kept fixed the head loss will …………. Please fill the blank with correct answer.
A horizontal pipe, originally smooth but due to constant use, was found to be scaling through corrosion where the effective surface roughness rises. This resulted for the fanning friction factor to be twice the original value. Determine the percent increase in the pipe diameter if the volumetric flowrate and pressure difference remains the same when it was new and old. Blank 1 %
Explain how flow rate is measured with a Pitot-static tube, and discuss its advantages and disadvantages with respect to cost, pressure drop, reliability, and accuracy.
If the two pipes in Fig. are instead laid in serieswith the same total pressure drop of 3 lbf/in2, what will theflow rate be? The fluid is SAE 10 oil at 20°C.
Determine the size of clean wrought-iron pipe (e=0.046 mm) required to convey 250 L/s of oil, =1x10-5 m2 /s), 3000 m long with a head loss of 25 m.N/N. [ Hint: Use Colebrook equation for transitionally rough pipe (whatever is the calculated f, that is final and no need to check if the pipe is smooth or rough).
SAE 30 oil at 20°C flows in the 3-cm-diameter pipe in Fig. which slopes at 37°. For the pressure measurementsshown, determine (a) whether the flow is up or down and(b) the flow rate in m3/h.
Oil, SG = 0.88 and ν = 4 E-5 m2/s, flows at 400 gal/minthrough a 6-in asphalted cast iron pipe. The pipe is 0.5 milong and slopes upward at 88 in the flow direction. Computethe head loss in ft and the pressure change.
The static head at a certain station on a 101.6 mm schedule 40, clean iron cold pipe is 70.69 m The static head is to be determined for a station 162.4 m farther along the pipe in the direction of flow,and where the pipe is 10.14 m higher than station 1. Between the stations are two elbows. Flow rateis 1452 l/min.
Sketch the shear stress and velocity distribution for laminar flow across a pipe section?
A circular, unfinished concrete drainpipe is laid on a slopeof 0.0025 and is planned to carry from 50 to 300 ft3/s ofrunoff water. Design constraints are that (1) the waterdepth should be no more than three-fourths of the diameterand (2) the flow should always be subcritical. What isthe appropriate pipe diameter to satisfy these requirements?If no commercial pipe is exactly this calculated size, should you buy the next smallest or the next largestpipe?
A 4in ductile iron pipe carries 0.20 ft3/s of glycerin (SG=1.26) at 100°F. Is the flow laminar or turbulent? Explain.