Question: A 12 mm thick plate is connected to two 8 mm thick plates, on either side through a 16 mm diameter power driven field rivet as shown in the figure below. Assuming permissible shear stress as 9- MPa and permissible bearing stress as 270 MPa in the rivet, the rivet value of the joint is P/2- P/2- 8 mm 8 mm 12 mm P

Question: A 12 mm thick plate is connected to two 8 mm thick plates, on either side through a 16 mm diameter power driven field rivet as shown in the figure below. Assuming permissible shear stress as 9- MPa and permissible bearing stress as 270 MPa in the rivet, the rivet value of the joint is P/2- P/2- 8 mm 8 mm 12 mm P

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 5 mm, and it is supported by double-shear pin connections at B and D. The pin at bracket A is a single-shear connection. All pins are 6 mm in diameter. Assume a = 600 mm, b = 250 mm, h = 425 mm, P = 900 N, and θ = 55°. Determine the the shear stress in pin B. Express your answer in MPa rounded to the nearest hundredths.
The lap joint shown in figure is fastened by four 1-in.-diameter rivets. (a) Calculate the minimum diameter of each rivet if the value of P is 30 kips and the bearing stress in the plates is limited to 4 ksi and the shearing stress in the rivets is limited to 15 ksi. Assume the applied load is uniformly distributed among the four rivets. Use 1 inch plate thickness.(b) Calculate the minimum thickness of plate if the value of P is 30 kips and the bearing stress in the plates is limited to 17.50 ksi. Assume the applied load is uniformly distributed among the four rivets.
The lap joint is connected by three 20-mm diameter rivets. Assuming that the axial load P= 50 kN is distributed among the three rivets, find the shear stress in each rivet. the bearing stress between the plate and a rivet. the maximum average tensile stress in each plate. Express your answer in MPa
1. For the riveted connection shown in the figure using elastic analysisa. Determine the safe value of P if the allowable shearing stress of 25mm rivets is 150MPab. Determine the maximum shearing stress that can be develop in the rivet for a given load ? = 52??c. Determine the minimum shearing stress that can be develop in the rivet for a given load ? = 52?N
As seen in the figure, ABC rod with end-A fixed support pipe section has an outer diameter of 30 mm and an inner diameter of 24 mm. 50 N force at an angle of 30 ° with the y-axis at the free end C to the ABC rod is implemented. (a)Show and calculate the cross-sectional effects on the cross-section a a. (b) Calculate the stresses occurring at the H point of the ABC bar and calculate these stresses
Given: Four-25-mm-diameter rivets with an axial load of T= 75 kN distributed equally as shown. The thickness of the plates is 25 mm and width of plate is 150 mm. find (a) the shear stress on the rivets(b) the bearing stress between a plate and a rivet;(c) the minimum average tensile stress in each plate. *PLS DRAW THE FREE BODY DIAGRAM *USE 3 decimals
A 4.8ft-long steel wire of 1/4in-diameter is subjected to a 750lb-Tensile load. Knowing that E=29x10^6psi, determine (a) the elongation of the wire, and (b) the corresponding normal stress.
1. The bar ABCD consists of 3 cylindrical steel segments with different lengths and cross-sectional areas. Axial loads are applied as shown. Calculate the normal stress in each segment in psi unit. Indicate if T or C.Calculate the total axial deformation in Problem #1 if Es = 29 x 10 6 psi . Indicate if the bar elongates or contracts.
Please answer correctly, badly need it. Thank u godbless The internal shear force at a certain section of a steel beam is V= 8.8 kN. The beam cross-section shown in the figure has dimensions of b=141 mm, c=31 mm, d=63 mm, and t=6 mm. Determine: (a) the shear stress at point H. (b) the shear stress at point K. (c) the maximum horizontal shear stress in the cross-section. Break the cross-section into five rectangles, as shown. It is seen that the two labeled with a (1) are identical, and the two labeled with a (2) are identical. Find A1, the area of rectangles (1), and y1, the vertical distance from the bottom edge of the cross-section to the centroid of rectangles (1). Similarly, find A2, the area of rectangles (2), and y2, the vertical distance from the bottom edge of the cross-section to the centroid of rectangles (2). Then, find A3 and y3 for rectangle (3). A1= mm2 y1= mm A2= mm2 y2= mm A3= mm2 y3= mm Find y¯, the vertical…
The five 20mm-diameter rivets fasten the plate as shown in the figure to the fixed member. a). Determine the value of the load P so that the average stress of any rivet does not exceed 80MPa.b). What additional clockwise torque can be applied before the shearing stress exceeds 90MPa
QUESTION: The distributed load on the T-section beam shown below and moment affects. A is the fixed joint and B is the sliding joint. This beam is made of a ductile material with a yield stress (σak) of 1000 MPa. The thickness (depth) of the beam profile is t=6 mm. A) As a mechanical engineer, check the strength of this beam (in terms of Normal and Shear Stress) ? B) In order for the existing beam to run smoothly, two 100x25 mm plates made of the same material are planned to be welded to this beam. The mechanical engineer working in the factory told the welder to weld this piece under the beam (where the B point is). But the welder, regardless of what the mechanical engineer said, welded this plate to both sides of the existing T-section beam as shown below, thinking that it wouldn't matter anyway. As a mechanical engineer : 1) After welding these plates on both sides of the beam, as the welder did, find out whether the new beam will work smoothly or not by making the necessary…
A steel plate 2.5 m x 1.3 m x 100 mm thick is to be hoisted by a steel cable sling as shown in the figure. Assume the steel weighs 77.3 kN/cu.m. Determine the bearing stress (MPa) in the steel plate the 10 mm diameter pins exert. The correct answer is 14.81. Show solution.