Question: A massless and inextensible rope C is wound around both discs of mass m. Please note that disc A does not move in a vertical or horizontal direction but can only undergo rotational motion. The discs are released from rest. Di Given: m=10 kg, R=90 mm, 1 = ½*m*R² Find: Tension in the stationary rope AD. Answer should be: (FAD =118 N) S A Я C B R

Question: A massless and inextensible rope C is wound around both discs of mass m. Please note that disc A does not move in a vertical or horizontal direction but can only undergo rotational motion. The discs are released from rest. Di Given: m=10 kg, R=90 mm, 1 = ½mR² Find: Tension in the stationary rope AD. Answer should be: (FAD =118 N) S A Я C B R

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.57P: Find the stable equilibrium position of the system described in Prob. 10.56 if m = 2.06 kg.

See similar textbooks

Similar questions

The 13-kg sphere C is released from rest when θ = 0∘ and the tension in the spring is F = 100 N. The figure shows rod AB hinged at point A. Sphere C is attached to the other end of the rod, labeled as B. Point D is located on the rod, 0.3 meters from point A and 0.15 meters from the center of the sphere. A spring with stiffness k of 500 newtons per meter is attached to the rod at point D by one of its ends. Another end of the spring is fixed at point E, located 0.4 directly above point A. The sphere is shown to be below and to the right of point A. An acute angle between the rod and the horizontal is labeled as theta. Determine the speed of the sphere at the instant θ = 90∘ . Neglect the mass of rod AB and the size of the sphere.
Rod OA rotates counterclockwise at a constant angular rate θ˙ = 4 rad/s. The double collar B is pin-connected together such that one collar slides over the rotating rod and the other collar slides over the circular rod described by the equation r=(1.6cosθ)m. Both collars have a mass of 0.7 kg . Motion is in the horizontal plane. (Figure 1)
A 0.150 kg frame, when suspended from a coil spring, stretches the spring 0.0400 m. A 0.200 kg lump of putty is dropped from rest onto the frame from a height of 30.0 cm (Fig.). Find the maximum distance the frame moves downward from its initial equilibrium position.
A physics student of mass 43.0 kg is standing at the edge of theflat roof of a building, 12.0 m above the sidewalk. An unfriendly dog isrunning across the roof toward her. Next to her is a large wheel mountedon a horizontal axle at its center. The wheel, used to lift objects from theground to the roof, has a light crank attached to it and a light rope wrappedaround it; the free end of the rope hangs over the edge of the roof. Thestudent grabs the end of the rope and steps off the roof. If the wheel hasradius 0.300 m and a moment of inertia of 9.60 kg . m2 for rotation aboutthe axle, how long does it take her to reach the sidewalk, and how fast willshe be moving just before she lands? Ignore friction in the axle.
A 256-lb block is released from rest when the spring is unstretched. The drum has a weight of 76 lb and a radius of gyration of kO = 0.9 ft about its center of mass O. The coefficient of stiffness of the spring is k=78 lb/ft. The radius of the drum are: rin=0.485ft and rout=0.82ft. Find the velocity of the block after it has descended d=4 feet.
While the system shown is in equilibrium, a counter-clockwise torque T =T0sin(ωt) N-m(with T0 = 226.6 and ω=7) is applied to teh disk. What is the disk angular speed ω0 = ? in rad/s at time t = 4.2 sec? ( I = 0.2 kg.m2, b = 7.8 N-m-s/r, k = 1,504 N/m, r = 0.52m )
The motorcycle in the figure has a mass of m1 kg and its center of mass is at G1. The mass of the driver is m2 kg and the center of mass is at G2. Since there is μs between the wheels and the asphalt, determine whether it is possible for the driver to lift the front wheel off the ground. Neglect the mass of the wheels and assume that the front wheel can spin freely. a=0.41 m b= 0.39 m c= 0.75 m d= 0.25 m e=0.58 m m1=120 kg m2= 77 kg μs=0.82
The thin rod in the figure has a mass of 15kg and is attached to a spring of constant k = 50 N / m at one end, which has an unstretched length of 1.5 m. If the rod is released from rest in a horizontal position (ѳ = 0 °) and only conservative forces act on it, determine:a) What is the moment of inertia of the thin rod around the axis of rotation at A? b) What is the angle at which the rod is momentarily at rest again? c) What is the maximum angular velocity of the path?
Consider the system of two blocks. Thereis no friction between block A and the tabletop. The mass of block B is5.00 kg. The pulley rotates about a frictionless axle, and the light ropedoesn’t slip on the pulley surface. The pulley has radius 0.200 m andmoment of inertia 1.30 kg . m2. If the pulley is rotating with an angularspeed of 8.00 rad/s after the block has descended 1.20 m, what is themass of block A?
A Proell governor has arms of 300 mm length. The upper arms are hinged on the axis ofrotation, whereas the lower arms are pivoted at a distance of 35 mm from the axis of rotation.The extension of lower arms to which the balls are attached are 100.1mm long. The massof each ball is 8 kg and the mass on the sleeve is 60 kg. At the minimum radius of rotation of 200mm, the extensions are parallel to the governor axis. Determine the equilibrium speed of thegovernor for the given configuration. What will be the equilibrium speed for the maximumradius of 250 mm?
The 5 kg cylinder is released from rest in the postion shown in the figure below. Determine the maximum compression xmax of the spring. The stiffness of the spring is 1800 N/m.
In the multi-rotor system shown below, m1=2 kg, m2=5 kg, r1=36 mm, r2=65 mm, z1=119 mm, z2=414 mm, θ1=118o, θ2=252o. We have 2 kg masses to balance the multi-rotor shaft. Answer questions a, b, c, and d accordingly. 1/ Determine the radius at which the 2 kg mass will be placed on the R plane (mm). a.35,763 b.268,220 c.53,644 D.107,288 2/Determine the angle (degrees) at which the 2 kg mass will be placed on the R plane. a.69,256 b.83,107 c.90,033 D.55,405 3/ Determine the radius at which the 2 kg mass will be placed on the L plane (mm). a.105,006 b.12,251 c.36,752 D.18,376 4/Determine the angle (degrees) at which the 2 kg mass will be placed on the L plane. a.30,085 b.37,607 c.43,248 D.45,128 solve the question by using the rules of Machine Dynamics