Consider the system of two blocks. Thereis no friction between block A and the tabletop. The mass of block B is5.00 kg. The pulley rotates about a frictionless axle, and the light ropedoesn’t slip on the pulley surface. The pulley has radius 0.200 m andmoment of inertia 1.30 kg . m2. If the pulley is rotating with an angularspeed of 8.00 rad/s after the block has descended 1.20 m, what is themass of block A?

Consider the system of two blocks. Thereis no friction between block A and the tabletop. The mass of block B is5.00 kg. The pulley rotates about a frictionless axle, and the light ropedoesn’t slip on the pulley surface. The pulley has radius 0.200 m andmoment of inertia 1.30 kg . m2. If the pulley is rotating with an angularspeed of 8.00 rad/s after the block has descended 1.20 m, what is themass of block A?

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.124P: The automobile, with center of gravity at G, is parked on an 18 slope with its brakes off. Determine...

See similar textbooks

Similar questions

Can the uniform bar of weight W remain at rest in the position shown?
The automobile, with center of gravity at G, is parked on an 18 slope with its brakes off. Determine the height h of the smallest curb that will prevent the automobile from rolling down the plane.
The 400-kg drum is held by tongs of negligible mass. Determine the magnitude of the contact force between the drum and the tongs at D.
The disk with a mass of 0.4 kg and a radius of 2 cm (I = 1 / 2mr ^ 2) slows down as it rolls on a flat surface. While the motion of the disc is the result of the moment of inertia, the friction coefficient is 0.1. Calculate the torque responsible for the deceleration of the disc
A wheel with rotational inertia 48 kg.m2 is mounted on a fixed, frictionless axle. The angular speed of the wheel is increased from zero to 59 rad/s in 12-s. What is the average net torque/Moment in N.m on the wheel during this time interval?
A demonstration gyroscope wheel is constructed by removingthe tire from a bicycle wheel 0.650 m in diameter, wrapping leadwire around the rim, and taping it in place. The shaft projects 0.200 mat each side of the wheel, and a woman holds the ends of the shaft inher hands. The mass of the system is 8.00 kg; its entire mass may be assumedto be located at its rim. The shaft is horizontal, and the wheel isspinning about the shaft at 5.00 rev/s. Find the magnitude and directionof the force each hand exerts on the shaft (a) when the shaft is at rest;(b) when the shaft is rotating in a horizontal plane about its center at0.050 rev/s; (c) when the shaft is rotating in a horizontal plane about itscenter at 0.300 rev/s. (d) At what rate must the shaft rotate in order thatit may be supported at one end only?
A caravan weighs 28 kN. It has a wheel base of 2 m, track width 1m and height ofC.G. 300 mm above the ground level and lies midway between the front andrear axle. The engine flywheel rotates at 2950 rpm clockwise when viewed from thefront. The moment of inertia of the flywheel is 4 kg-m 2 and moment of inertia ofeach wheel is 3 kg-m 2 . Find the reactions between the wheels and the ground whenthe car takes a curve of 15 m radius towards right at 30 km/h, taking intoconsideration the gyroscopic and the centrifugal effects. Each wheel radius is 400 mm.
Determine the rotational inertia of the device shown below. R = 0.50 m, r = 0.2 m, the mass of the box is 30 kg. When Fapp= 176 N, the box has an upward acceleration of 0.8 m/s2. Use g = 9.8 N/kg.
A cylinder with rotational inertia 0.050 kg m2 is spinning with angular velocity 25 rad/s, clockwise with negligible friction about a vertical axis. A second cylinder that is not spinning is centered above and dropped onto the spinning cylinder. Kinetic friction produces torque of amount 0.60 Nm that affects both objects until the two cylinders spin together at angular velocity 18 rad/s, clockwise. (a) Determine the amount of time it takes for friction to cause the two objects to spin together.(b) Determine the rotational inertia of the second cylinder that was dropped onto the first.(c) Determine the total amount of heat and sound energy resulting from the interaction of the cylinders.
the cylinder with a mass m1=2kg and radius r=0,1m is placed at a plate with mass m2=4kg. We are applying force F at this plate. Find an acceleration of the plate, when the friction coefficient μ=0,2
The frame of a gyroscope in fig. is supported at O so that it can turn freely in alldirections. The wheel is a uniform disc of 10 cm diameter weighing 2 kg with its centre20 cm from O. The frame alone weighs 1 kg with centre of gravity G1, 12 cm from O.If the wheel spins as shown at 10,000 r.p.m. with its axle in the horizontal plane, findthe time required for the axle to make one revolution about O. Mention the direction ofthis rotation. Find also the vertical and horizontal forces by the support on the frame.
A uniform wheel of 60 cm dameter and 800N weight rests agairst a rigid rectanguar bbck of thickress 25 cm Considering all surfaces smooth, determine (a) kast pul to be applied through the centre of the wheel to just tum i over the corner of the bbck, (b) reaction of the bbck.