Question Flow Using the Gap MethodThe single door shown in Figure 3.3 has the following dimensions:DimensionThickness of gap in direction perpendicular to flow, aDepth of gap in flow direction, xLength of gap, LHydraulic diameter, D = 2aBottom Slot0.25 in. (0.00635 m)1.75 in. (0.0445 m)3 ft (0.914 m)0.5 in. (0.0127 m)The air density is 0.075 lb/ft³ (1.20 kg/m³), and the kinematic viscosity is 1.64x10ft/s (1.52x10-5 m²/s).What is the volumetric flow with a pressure difference, Ap=0.15 in H₂O (37 Pa)?Door(a) Single doorDoorooDoorDoor(c) Gap at bottomTop and Side Slots0.1 in. (0.00254 m)2.37 in. (0.0602 m)17 ft (5.18 m)0.2 in. (0.00508)HDoors Door(e) Gap at center of(b) Double doordouble doorsGaps around single and double doors.Door Frame(d) Gap at lopand sides

Answered: Image /qna-images/answer/e17b3e41-8a87-42eb-8733-0aab88c572d5.jpg

Question Flow Using the Gap Method The single door shown in Figure 3.3 has the following dimensions: Bottom Slot 0.25 in. (0.00635 m) 1.75 in. (0.0445 m) 3 ft (0.914 m) 0.5 in. (0.0127 m) The air density is 0.075 lb/ft³ (1.20 kg/m³), and the kinematic viscosity is 1.64×104 ft/s (1.52x10-5 m²/s). What is the volumetric flow with a pressure difference, Ap=0.15 in H₂O (37 Pa)? Dimension Thickness of gap in direction perpendicular to flow, a Depth of gap in flow direction, x Length of gap, L Hydraulic diameter, D = 2a Top and Side Slots 0.1 in. (0.00254 m) 2.37 in. (0.0602 m) 17 ft (5.18 m) 0.2 in. (0.00508)

Question Flow Using the Gap Method The single door shown in Figure 3.3 has the following dimensions: Bottom Slot 0.25 in. (0.00635 m) 1.75 in. (0.0445 m) 3 ft (0.914 m) 0.5 in. (0.0127 m) The air density is 0.075 lb/ft³ (1.20 kg/m³), and the kinematic viscosity is 1.64×104 ft/s (1.52x10-5 m²/s). What is the volumetric flow with a pressure difference, Ap=0.15 in H₂O (37 Pa)? Dimension Thickness of gap in direction perpendicular to flow, a Depth of gap in flow direction, x Length of gap, L Hydraulic diameter, D = 2a Top and Side Slots 0.1 in. (0.00254 m) 2.37 in. (0.0602 m) 17 ft (5.18 m) 0.2 in. (0.00508)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rectangular duct is 81⁄4 inches wide. The throat radius of this 45° elbow is51⁄2 inches.a. Find the inside arc length. a.b. Find the outside arc length.
An opening is made at the bottom of a damn 144 ft high. Find the approximate velocity of the water that will flow through the opening if friction is neglected. a 45 ft/sec b. 900 ft/sec c. 96 sec d 750 sec
Please also explain the process of finding the flow nets
SHOW COMPLETE SOLUTION PLSVALUES: A= 5 C = 5 Y= 25
LL=75 and PL=40. 100% passing on Sieve 200.
Really need ASAP A rectangular channel (n=0.011) 18m wide is to carry water at a flow rate of 35 m3/s. The slope of the channel is 0.00078 Determine the critical depth of flow in m Choices: 0.73 3.7 7.3 0.37 Note: this is the only given information and also not graded test please help me ASAP thank you
SHOW COMPLETE SOLUTION PLSVALUES: Y = 25C = 1
Problem 1 You are to design a 800’ long sewer pipe that is to be placed in a trench. Prepare an Excel table showing the design elevations every 100 feet. Use stationing of 0+00 for the beginning, and 8+00 for the end. Place the pipe at a gravity drainage slope of -2.5% towards station 8+00. The invert elevation of the pipe at 0+00 is 6375.00’. The pipe has an outside diameter of 1’ and a wall thickness of 1”. Your design needs to include the following:a) List the elevations for the top of the pipe for the plus stations (0+00, 1+00, 2+00, 3+00, 4+00, 5+00, 6+00, 7+00, and 8+00) *.b) Calculate the invert elevation for the pipe at station 8+00 *Note: Elevations for the top of the pipe are used to place leveling rods at those stations and control the depth of the pipe during construction (since the bottom of the pipe is then inaccessible).Hint1: Make a sketch.Hint2: A 3% gravity slope means -3’ per 100’ (as in “three per cent”). “3%” is not an angle.Hint3: For short distances (i.e., pipe…
Create CPM Diagram with forward pass and backward pass methods.
A 0.09m^2 standard circular orifice is illustrated in a 2m^2 square vessel that is 3m high. Make the time to use the aperture to empty the vessel C equals 0.60. Answer t = 32.26 sec
What size of new cast iron pipe in millimeter shall be used to carry 4,735 gpm with a lost of head of 15.34 feet per mile? Assume f = 0.019. Write numerical value only and in 2 decimal places. show solution.
For a flow of 1500 liters of water per second through a circular channel of 2 m diameter flowing half full. The value of Manning's constant is 0.015 for the rough concrete lining used. Compute the slope required for the flow in the channel. CHOICES: *1/1934 *1/551 *1/1569 *1/3295 Please answer with complete and detailed solutions. thank you. ASAP