The extruded plastic shape has dimensions of D = 37 mm, d = 35 mm, a = 91 mm, and t = 4 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 385 N. (b) If the allowable shear stress for the plastic material is 2200 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion?

The extruded plastic shape has dimensions of D = 37 mm, d = 35 mm, a = 91 mm, and t = 4 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 385 N. (b) If the allowable shear stress for the plastic material is 2200 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion?

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter8: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 8.13P

See similar textbooks

Similar questions

A closed cylindrical tank, placed horizontally, 400 mm in internal diameter and 2.2 mm thick is subjected to an axial compressive force (along its longitudinal axis) and uniform internal pressure. The stresses acting on an element of side is shown in the figure. a. What is the magnitude of the internal pressure in MPa?b. What is the applied axial force in kN?c. What is the maximum shear stress in MPa?
refer to the figure due to application of line load q1 and q2 . the vertical stress increase at point a is 42 kn/m2 determine the magnitude of q
A square hollow bar having an outside dimension of 250 mm by 250 mm with 6 mm thick is to be replaced by a solid circular bar. a) Determine the required diameter of bar so that the maximum shear stress in the bar will not exceed the maximum shear stress in the tube. b) If the computed value of diameter in the previous question increase by 15%, what is the new shear stress of the circular bar? c) Determine the angle of twist in degrees of the tube if the length of the tube is 1m and the shear modulus is 80 GPa. Use T=14 kN-m.
An axial load of 100 kN is applied to a flat bar 20 mm thick, tapering in width from 120 mm to 40mm in a length of 11 m.Assuming E=200GPa, Determine the total elongation of the bar.
According to the elastic theory, the vertical stress induced by a point load of magnitude Q on the surface of a semi-infinite soil mass can be estimated by the expression. A point load Q=1500 kN is applied at the ground surface. Evaluate the stress in the soil caused by the point load at a depth of 2.5m directly below the load in kPa. Evaluate the stress at a depth of 2.5m and a horizontal distance of 3m from the point load.
The stresses shown act at a point in a stressed body. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 17 MPa, Sy = 29 MPa, and Sxy = 26 MPa. Assume β=tan^−1(b/a)=23.2∘, a = 7, and b = 3. Using the equilibrium equation approach, determine the normal and shear stresses σ (positive if tensile, negative if compressive) and ττ (magnitude only) at this point on the inclined plane shown.
The center of a rectangular area at the ground surface has Cartesian coordinates (0, 0), and one corner has coordinates (7, 18). All dimensions are in meters. The area carries a uniform pressure of 135 kPa. Estimate the stresses at a depth of 15 meters below the ground surface at each of the following locations: (0, 0), (0, 18), (7, 0), (7, 18), and (12, 28).a. Obtain the values by the Boussinesq methodb. Compare the results with those of the 2:1 methodc. Comment on the resultsHint: In the Boussinesq method, the equations attached can be used.
The extruded plastic shape will be subjected to an internal shear force of V = 280 lb. Dimensions of the cross section are b = 1.1 in., d = 2.2 in., c = 1.5 in., and t = 0.20 in. Determine:(a) the magnitude of the horizontal shear stress at points A and B.(b) the magnitude of the horizontal shear stress at point C, which is located at a distance of yC = 0.8 in. below the z centroidal axis.(c) the magnitude of the maximum horizontal shear stress in the extrusion.
If the hoop stress on a cylindrical pressure vessel with diameter d, thickness t and gauge pressure p is 58.54 MPa, then the longitudinal stress must be equal to (in MPa)...
The center of a rectangular area at the ground surface has Cartesian coordinates (0, 0), and one corner has coordinates (7, 18). All dimensions are in meters. The area carries a uniform pressure of 135 kPa. Estimate the stresses at a depth of 15 m below the ground surface at each of the following locations: (0, 0), (0, 18), (7, 0), (7, 18), and (12, 28).a. Obtain the values by the Boussinesq methodb. Compare the results with those of the 2:1 methodc. Comment on the resultsHint: In the Boussinesq method, the equations attached can be used.
The rectangular bar shown in the figure is subjected to a uniformly distributed axial loading of w = 11 kN/m and a concentrated force of P = 14 kN at B. Determine the magnitude of the maximum normal stress in the bar and its location x. Assume a = 0.9 m, b = 1.1 m, c = 20 mm, and d = 35 mm.
The extruded plastic shape will be subjected to an internal shear force of V = 350 lb. Dimensions of the cross section are b = 2.0 in., D = 4.0 in., C = 2.7 in., And t = 0.19 in. Determine: (a) the magnitude of the horizontal shear stress at points A and B. (b) the magnitude of the horizontal shear stress at point C, which is located at a distance of yC = 1.4 in. below the z centroidal axis. (c) the magnitude of the maximum horizontal shear stress in the extrusion