Question Four Air enters a pipe at a Mach number of 2.5, a temperature of 400 °C and a pressure of 70 kPa. The pipe has a diameter of 2.0 cm and the flow can be assumed to be adiabatic. A shock occurs in the pipe at a location where the Mach number is 2. If the Mach number at the exit from the pipe is 0.8 and if the average friction factor is 0.005. Find the distance of the shock from the entrance to the pipe and the total length of the pipe. Also, find the pressure at the exit of the pipe.

Question Four Air enters a pipe at a Mach number of 2.5, a temperature of 400 °C and a pressure of 70 kPa. The pipe has a diameter of 2.0 cm and the flow can be assumed to be adiabatic. A shock occurs in the pipe at a location where the Mach number is 2. If the Mach number at the exit from the pipe is 0.8 and if the average friction factor is 0.005. Find the distance of the shock from the entrance to the pipe and the total length of the pipe. Also, find the pressure at the exit of the pipe.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Nitrogen enters a duct with varying flow area at 400 K, 100 kPa, and a Mach number of 0.3. Assuming a steady, isentropic flow, determine the temperature, pressure, and Mach number at a location where the flow area has been reduced by 20 percent.
Air flowing at 8 psia, 480 R, and Ma1 = 2.0 is forced to undergo a compression turn of 15°. Determine the Mach number, pressure, and temperature of the air after the compression.
Air flowing steadily in a nozzle experiences a normal shock at a Mach number of Ma = 2.5. If the pressure and temperature of air are 10.0 psia and 440.5 R, respectively, upstream of the shock, calculate the pressure, temperature, velocity, Mach number, and stagnation pressure downstream of the shock. Compare these results to those for helium undergoing a normal shock under the same conditions.
Air flowing steadily in a nozzle experiences a normal shock at a Mach number of Ma = 2.6. If the pressure and temperature of air are 58 kPa and 270 K, respectively, upstream of the shock, calculate the pressure, temperature, velocity, Mach number, and stagnation pressure downstream of the shock. Compare these results to those for helium undergoing a normal shock under the same conditions.
Air flowing at 32 kPa, 240 K, and Ma1 = 3.6 is forced to undergo an expansion turn of 15°. Determine the Mach number, pressure, and temperature of air after the expansion.
Air flows from a large tank where the pressure and temperature are 600 kPa and 800 K, respectively, through a converging nozzle with an exit area of 0.0005 m2 and discharges to the atmosphere with a pressure of 100 kPa. The flow Is lsentroplc throughout the nozzle. Determine the Mach number, temperature, pressure and velocity at the exit section, and also calculate the mass flow rate.
A converging duct is fed with air from a large reservoir where the temperature and pressure are 400 K and 200 kPa, respectively. The Mach number at a point along the duct, where the cross•sectional area is 0.01 m', is 0.7. Determine the temperature, pressure, velocity and density at that point, and also calculate the mass flow rate. Assume lsentropic flow throughout the nozzle.
Mach number at a certain section in a diverging part of a c-d nozzle is 0.7. At farther section (towards the exit), Mach number reduces to 0.4. Hence, the cross-sectional area of the farther section is greater by
The Airbus A-340 passenger plane has a maximum takeoff weight of about 260,000 kg, a length of 64 m, a wing span of 60 m, a maximum cruising speed of 945 km/h, a seating capacity of 271 passengers, a maximum cruising altitude of 14,000 m, and a maximum range of 12,000 km. The air temperature at the crusing altitude is about −60°C. Determine the Mach number of this plane for the stated limiting conditions.
Can the Mach number of a fluid be greater than 1 after a normal shock wave? Explain.
Consider air entering a heated duct at p1 = 1 atm and T1 = 288 K. Ignore the effect of friction. Calculate the amount of heat per unit mass (in joules per kilogram) necessary to choke the flow at the exit of the duct for an inlet Mach number of M1 = 2.2.
Air at a total pressure and temperature of 8 atm and 450 K enters a frictionless constant cross-section duct. A heat addition of 850 kJ/kg makes the flow to choke at the duct exit, determine the inlet Mach number and the total pressure and total temperature at the exit.