Question One Figure Q1 shows a stress state element in a material component. Analyse the element and calculate the principal stresses and positions of the principal planes in the component, using: 1.1 Formulae; 1.2 First principles 120 MPa 80 MPa need neat and clean handwritten solution of both parts for upvote Figure Q1. 25 MPa

Question One Figure Q1 shows a stress state element in a material component. Analyse the element and calculate the principal stresses and positions of the principal planes in the component, using: 1.1 Formulae; 1.2 First principles 120 MPa 80 MPa need neat and clean handwritten solution of both parts for upvote Figure Q1. 25 MPa

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.5P: The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen...

See similar textbooks

Similar questions

The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
Hi, I need help with this question please. Thank you. A cantilever thin-walled cylindrical tube of inner diameter ? = 30cm and thickness ? = 1cm is subjected to a torque T and internal pressure p as shown below. The free end of the tube is closed. Strain gauges A and B mounted on the surface of the cylinder give readings ?? = 7.5 × 10^−6 and ?b = 19.7x10^−6, respectively. The bar is made of steel having Young's modulus E=200 GPa and Poisson's ration ? = 0.3. a) Determine the torque, T, and internal pressure, p. b) Determine the absolute maximum shear strain ???? at point C.
A steel bar 25cm long of rectangular cross section 25mm by 50mm is subjected to a uniform tensile stress of 200N/m^2 along it's length.find the changes in dimension.E=205000N/mm^2, poison ratio=0.3
mechanics deformable bodies 1. A hollow steel shaft has an outside diameter of 220 mm and an inside diameter of 200 mm. Which of the following nearly gives the torque in kN-m that will cause stress of 75.5 MPa in the shaft?
The stresses shown act at a point on the free surface of a machine component. Normal and shear stress magnitude acting on horizontal and veritcal planes at the point are Sx= 12.7 ksi, Sy= 1.7 ksi, Sxy= 5.8 ksi. Assume beta= 34 degrees. Determine the normal stresses and shear stress
A cylindrical rod AB has a length ? = 80 cm and a diameterof ? = 2 cm. The modulus of elasticity is ? = 200 GPa andyield strength is ?? = 300 MPa. The stress-strain diagram ofthe rod is shown in the left figure. A force ? = 100 kN isapplied to the bar and then fully removed (right figure).Determine the permanent set in the rod.
STRENGTH OF MATERIALS. Please show the complete solutions. Rate will be given. Answer in 3 decimal places! The compound shaft consists of solid steel and bronze shafts and hollow aluminum shaft (D= 2.25" and d=0.90''). It is subjected to two torques as shown in the figure. The moduli of rigidity for steel, aluminum, and bronze are 12x106 psi, 4x106 psi, and 6x106 psi, respectively. Determine the shearing stress developed in each material. Also, calculate the angle of twist incurred by the aluminum shaft.
Consider a 1,000-mm long, 25-mm diameter sample subjected to a tension test. Automatic high-precision gages recorded that for an applied load of 150 kN, the sample experienced a longitudinal strain of 2×10−3mm/mm. Assuming that the material remained elastic while loaded, determine its modulus of elasticity. A. 175.0 GPa B. 63.7 GPa C. 152.8 GPa D. 72.9 GPa Which of the following occurs when the value of Poisson’s ratio is doubled and the modulus of elasticity is kept constant? a. The lateral deformations experienced by the material is halved b. The volume of the material will remain constant when subjected to external forces c. The elastic region of the shear stress-strain diagram would be less steep d. The material can withstand higher amounts of stress before permanent deformations occur
Defferentiate the following terms; 1.Resilience and proof resilience 2.proof resilience and modulus of resilience B)A solid beam ABC circular in section has varying sections.portion AB is 6m in length and diameter of 250mm while portion BC is 2m in length and section diameter of 100mm.The beam is subjected to a sudden tensile load.if the maximum stress induced is 400MN/m^2.Determine the strain energy stored in the beam.Take E=200GN/m^2
For the point given the plane stress state, which of the following is the correct type and limit values of Mohr Circle? sx =-40 MPa (Bası), sy =60 MPa (Çeki) txy =60MPa
STRENGTH OF MATERIALS. Please show the complete solutions. NO LONG EXPLANATION NEEDED! Rate will be given. Answer ASAP! Please answer all. MULTIPLE CHOICE: CHOOSE THE CORRECT ANSWER 1. Using MOHR CIRCLE from the given stresses on two perpendicular planes what is the normal stress on plane a-a? a. 75 MPa b. 150 MPa c. 125 MPa d. 100 MPa