Question What must be the minimum power rating for the external pass transistor used with a 7815 regulator in a circuit such as that shown in Figure below? The input voltage is 30 V and the load resistance is 10 N. The maximum internal current is to be 700 mA. Assume that there is no heat sink for this calculation. Keep in mind that the use of a heat sink increases the effective power rating of the transistor and you can use a lower rated transistor. Qext VIN O Rest VOUT 7815 C2 RL

Question What must be the minimum power rating for the external pass transistor used with a 7815 regulator in a circuit such as that shown in Figure below? The input voltage is 30 V and the load resistance is 10 N. The maximum internal current is to be 700 mA. Assume that there is no heat sink for this calculation. Keep in mind that the use of a heat sink increases the effective power rating of the transistor and you can use a lower rated transistor. Qext VIN O Rest VOUT 7815 C2 RL

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

If a sinusoidal voltage is applied to the base of a biased npn transistor and the resulting sinusoidal collector voltage is cut to near zero volts, what is the state of the transistor? Please select one: a. answers B and C b. interrupted drive c. answers A and C d. forced into nonlinear operation e. drifting into saturation
NOTE: FOR ALL CIRCUITS SHOWN IN THIS QUIZ ASSUME THAT: β= 100 (for all transistors) ; Early voltage equal to infinity. 2. - For the circuit shown in figure B, determine:a) The values of IcQ and VceQ for Q1 and Q2b) The input resistance Ri and the output resistance Ro
Subject:Electronics Engineering With a neat circuit diagram, explain the Voltage Divider Bias circuit using approximate analysis. Also derive the equation of stability (S) for Voltage Divider Bias circuit.
You are required to design the heatsink for the power transistor of a voltage regulator, keeping the heatsink cost minimal. The voltage regulator has an output voltage of 5 V and full load current of 500 mA. At full load, the regulator efficiency is 25 %, with the power transistor contributing to 45% of the power loss. The regulator is expected to operate at ambient temperature of between 20 °C and 40 °C. The heatsink temperature should not be more than 80 °C. Assume the cost of the heatsink is inversely proportional to the value of the thermal resistance  SA. The power transistor has the following parameters:  JC = 3 °C /W TJ,max = 150 °C Determine the thermal resistances,  CS and  SA.
Explain how the ac gain of a transistor can be controlled by a dc AGC level. DON'T COPY FROM ANY WEB. WRITE IT IN YOUR WORDS.
The dc load line on a family of collector characteristic curves of transistor shows the........ Choose correct answer : A) All operating regions B) cut-off region only C) active region only D) saturation region only
(a) What is the output current IO in the circuitshown if −VEE = −10 V andR = 20 ohm? Assume that the MOSFET is saturated.(b) What is the minimum voltage VDDneeded to saturate the MOSFET if VTN = 2.5 Vand K'n = 0.25 A/V2. (c) What must be the powerdissipation ratings of resistor R and the FET.
a. Calculate the common-mode gain for the amplifier circuit. b. Calculate the common-mode gain for the differential amplifier.
A. Determine the VCE transfer as a function of Vi of the circuit in figure 1, (eliminating the zener diode), indicating the different areas of the transistor (Active zone VBE = 0.7v, VCEsaturation = 0.2v, VBSaturation = 0.8v; saturation zone: The transistor has a B = 110 and the reverse saturation current negligible. B. As in section a) with the zener diode, assuming that this is ideal, whose zener voltage is equal to 3.5Volts. R3=8K, R4=9K
Explain the working of Binary Weighted Resistor Digital to Analog converter with a neat diagram.
What is the output voltage vO if theop-amp is ideal? What are the values of the baseand emitter currents and the total current suppliedby the 15-V source? Assume βF = 60. What is theop-amp output voltage?
For the class B output stage of Figure 2, let ??? = 6 V and ?? = 4Ω. If the output is a sinusoidal with 4.5V peak amplitude, find; (a) The output power. (b) The average power drawn from each supply/ (c) The power efficiency obtained at this output voltage. (d) The maximum power that each transistor must be capable of dissipating safely.