Question:1A diode whose internal resistance (forward biased) is 20 2 is to supply power to a 1000 Q loadfrom a 110 Vr,m.s Ssource of supply.Calculate:i. The peak load currentii.iii. The A.C. load currentThe D.C. diode voltageThe total input power to the circuitThe D.C. load currentiv.V.R = 202110 Vr.m.s.RL10002

Note: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question…

Question:1 A diode whose internal resistance (forward biased) is 20 Q is to supply power to a 1000 2 load from a 110 Vm.s source of supply. Calculate: The peak load current ii. i. The D.C. load current iii. The A.C. load current iv. The D.C. diode voltage The total input power to the circuit V. R = 202 110 V r.m.s. RL 10002

Question:1 A diode whose internal resistance (forward biased) is 20 Q is to supply power to a 1000 2 load from a 110 Vm.s source of supply. Calculate: The peak load current ii. i. The D.C. load current iii. The A.C. load current iv. The D.C. diode voltage The total input power to the circuit V. R = 202 110 V r.m.s. RL 10002

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2P: The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where...

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
What is CEMF?
The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where R1 and R2 are the resistances at temperatures T1 and T2, respectively, and is known as the temperature coefficient of resistance. If a copper wire has a resistance of 55 at 20C, find the maximum permissible operating temperature of the wire if its resistance is to increase by at most 20. Take the temperature coefficient at 20C to be =0.00382.
diode zener a, DESIGN THE NETWORK IN THE FIGURE, TO KEEP, "VL" at 12 V for a variation in load (IL) from 0 to 200 mA, DETERMINE "Rs" and "Vz" b. determine "P2min" for the Zener diode from section a
Consider the circuit. a) What type of circuit is this? b) What is the total peak secondary voltage? c) Find the peak voltage across the each half of the secondary. d) Sketch the voltage waveform across RL. e) What is the peak current through each diode? f) What is the PIV of each diode?
Load resistor RL as shown is 12 kΩ. What are the nominal and worst-case values of Zener diode current and power dissipation if the power supply voltage, Zener breakdown voltage and resistors all have 5 percent tolerances?
Answer the following questions according to the above. Remember Kirchhoff's laws when making your calculations in this question. a) According to the given graph, how many volts is the voltage value on it when this Zener diode is on a flat supply? b) According to the given graph, how many volts is the voltage value on this Zener Diode when it is on reverse supply? c) Calculate how many values V?−?? are when the zener current is 0 mA. D) Calculate how much the value of ??−?? is when the zener current is at its maximum value.
Two identical Schottky diodes are connected in series, one in the forward and the other in reverse direction, see figure. Assume the reverse saturation current, IS, of each diode to be known. Derive he current-voltage curve I(V) of this circuit. Plot it with the ratio I / IS on the y-axis and V / Vth on the x-axis. Make sure to cover a broad range of voltages, say, from –10 Vth to 10 Vth.
Determine Q-point for the diodes in the circuit given below using the ideal diode model where, R1 = 12.2 kΩ, R2 = 16 kΩ, and R3 = 14 kΩ. (Note: Label the diodes from left to right.)
Briefly discuss the difference between Diode Piecewise-linear model, Simplified model, and Ideal device/ equivalent circuit. Study the diode specification sheets of a 1N4001 and 1N5401 diodes provided by the manufacturer and compare their difference. Give typical application of each. Discuss briefly how to test junction diode.
A full-wave bridge rectifier with a 236.86V p-p sinusoidal input has a load resister of2KΩi. Draw the wave form that the load resistor R would see. ii. Assuming diodes are ideal, what is the dc voltage available at the load resistor? iii. What is the dc voltage available at the load if silicon diodes are employed? iv. Calculate the maximum current flow through the Diode D4 during conduction.
Q.) For the circuit shown, if the voltage Vin as shown is positive, which Zener diode functioned as a Zener diode?