Question:choose the correct answer consider(V-12v,R1-200KQ,R2-300K2,R3-40OKN)for the electric circuit shown in The figure: Resistori DC Voltage Source Resistor2 Resistor3 NOT:(it may be more than a correct answer) 1-the value of he current passing through resistance NO.2 ISs: (a) 0.02mA (b) 0.04mA (c) 0.00002A (d) 0.00004A

Question:choose the correct answer consider(V-12v,R1-200KQ,R2-300K2,R3-40OKN)for the electric circuit shown in The figure: Resistori DC Voltage Source Resistor2 Resistor3 NOT:(it may be more than a correct answer) 1-the value of he current passing through resistance NO.2 ISs: (a) 0.02mA (b) 0.04mA (c) 0.00002A (d) 0.00004A

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Write the KVL & KCL equations for the circuit shown. Draw again the circuit and indicate what is the direction of the current in the loop and what is the direction of the current in the resistors. KVL & KCL at: node b: node c: node g: node f: Thank you!
Three resistances (10 ohms, 20 ohms, and 30 ohms) are connected in series with a 100-V power source. If a 50-V power source is connected parallel to the 10-ohm resistor, determine the power dissipated by the 20-ohm resistor.
For the circuit shown in the figure below, find the following. the current in each resistor,I2Ω(top) =,I2Ω(middle) =,I6Ω =,the power supplied by each source of emf P 4V(top) =,the power delivered to each resistorP 1Ω =,P6 Ω =,P2Ω(middle)=
Obtain V0 equation from Figure below and calculate V0 for V1=2V, V2=3V and V1=2V, V2=4V. R3=2k, Rf3=10k. calculate V0 and the values of currents on all the resistors.
3. In figure 3 R1 = 1 ohm, R2 = 1 ohm, R3 = 3 ohms, I2 = 2A and VB = 120 V. Find Eg. In the DC circuit as shown in figure 4, the high resistance voltmeter gives a reading of +0.435 volt. What is the value of the resistance R?
Use the reduce and return circuit analysis approach to solve for all voltages and currents in the circuit shown in figure 1 RT v1 v2 v3 v4 v5 IT I1 I2 I3 I4 I5 PE PR1 PR2 PR3 PR4
3. A lamp having a specification of 220 V/100 W is connected in series with resistance 516Ω, then mounted on a voltage of 110 W. Determine: (a) the current flowing in the circuit (b) the power produced by the lamp Solve with the full step thank u
Apply Nodal analysis on the circuit shown in Figure 1 and write equations below. Compute and measure the voltages V3, V4, V5 and and current through resistors R2 and R6 copy the values in Table 1 Note: Values of resistors (R2 & R6) will be your 120K ohm and voltage sources will be V1=5V & V2=10V.
An ammeter is used as shown in Figure P2.78. Theammeter model consists of an ideal ammeter in serieswith a resistance. The ammeter model is placed in thebranch as shown in the figure. Find the current throughR5 both with and without the ammeter in the circuit for the following values, assuming that RS = 20 ,R1 = 800 , R2 = 600 , R3 = 1.2 k, R4 = 150 ,and VS = 24 V.a. R5 = 1 kb. R5 = 100 c. R5 = 10 d. R5 = 1
Finding the direction of the currents. Finding currents given that R2: 10.94 x 10^2 ohmR3: 9.89 x 10^2 ohmR4: 25 ohm Terminal Potential: Battery 1: 5 V using Kirchoff's laws. You will check some of the laws that govern electrical circuitsDirect current: conservation of current in a node, addition of potentialsfor series components, addition of currents for parallel components
find the following using the attached picture: (a) Calculate the equivalent resistance of this circuit. (b) Calculate the following quantities:1). current through R52). current through R33). voltage across R1 (c) To measure the current flow though R1 and the voltage onR5, how should we connect the ammeter and voltmeter?Draw a circuit diagram showing your answer. (d) What is the ideal impedance of1). an ammeter?2). a voltmeter?
Four resistors, R1 = 100 N, R2 = 250 N, R3 = 350 N and R4 = 200 N are connected such that the parallel combination of R, and R2 is connected in series with the parallel combination of R3 and R4. The series-parallel combination is then connected across a 24 V DC power supply. A Draw the schematic diagram and label the circuit elements. B. Calculate the equivalent resistance of the circuit. (Ans. Reg = 198.7013 N) C. Find the total current of the circuit, the voltage across each resistor and the current through each resistor. Ans: (IT = 0.1208 A, V1 = V2 = 8. 6275 V, V3 = V4 = 15.3725 V, I = 0.0863 A, I2 = 0. 0345 A, I3 = 0.0439 A, I4 = 0.0769