QUIZ 2 Figure Q1 shows a truss structure, which is pinned at A and roller supported at C. Horizontal load and vertical load are applied to the truss at joint D and B respectively as shown in the Figure. By using virtual work method, determine the vertical displacement at joint B. Given that the area of each of the member, A=300mm², while the elastic modulus, E = 200GPa (CO3, C4). F E 15KN 2.0m B 2.0m A 40KN Figure Q1 1.5m C 000

QUIZ 2 Figure Q1 shows a truss structure, which is pinned at A and roller supported at C. Horizontal load and vertical load are applied to the truss at joint D and B respectively as shown in the Figure. By using virtual work method, determine the vertical displacement at joint B. Given that the area of each of the member, A=300mm², while the elastic modulus, E = 200GPa (CO3, C4). F E 15KN 2.0m B 2.0m A 40KN Figure Q1 1.5m C 000

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the force in each member of the structure and establish whether the members are in tension or compression. Establish P1= 45 KN, P2= 30 KNSolve the problem considering the following: The force P1 will be the maximum point of a triangularly distributed load with a horizontal distribution of X meters.You must leave the solution in terms of X and show the particular solution when X is equal to 0m and 2m.
Determine the force in each member of the structure and establish whether the members are in tension or compression. Establish P1= 45 KN, P2= 30 KN Solve the problem considering the following: The force P1 will be the maximum point of a triangularly distributed load with a horizontal distribution of X meters. You must leave the solution in terms of X and show the particular solution when X is equal to 0m and 2m.
T (Shear force) and M (Bending) for the system whose loading condition is given in Figure 1.Draw the moment diagrams. Calculate the deflection (vertical displacement) at point B in mm using Castigliano's Theorem. The beam bending stiffness (EI) is constant along the bar and its value is 50 000 kNm2. q=1,4(kN/m) a=8(m) El=50000(kNm2)
For the truss shown, determine the vertical displacement of joint A in mm. Use E= 200 kN and A= 6000 mm2
3.) For the given couple-force system shown, determine the horizontal component of Q. P= 335 KN Q= 44 KN R=74 KN-m Z=263 KN
As shown in the figure, aluminum rod AB and steel rod BC, hinged to rigid supports, are pinned together at B to carry a vertical load P = 6000 lb. If aluminum rod has a cross-sectional area of 0.60 in.² and E = 10 × 103and steel rod has 0.50 in.² and E = 29 × 106 each rod and the horizontal and vertical displacements of point B. Assume α = 60° and θ = 30°. ksi, psi, compute the elongation of
1) Determine the value of EIy at x = 3m from the left support, for the beam loaded as shown in Figure Q1.
determine the vertical reaction at B in kN using any Geometric Method. Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Enter the absolute value only and round-off your answer to 3 decimal places
The T-shaped beam shown above is supporting a concentrated load P at its free end. The beam has an allowable bending stress of ?????? = 250 MPa and an allowable shear stress of ?????? = 100 MPa. a) Determine the distance to the neutral axis (?̅), second moment of area (?), and the section modulus (?) of the cross-section.b) Draw the shear force diagram (SFD) and bending moment diagram (BMD) of the beam. On your diagrams, express the values of shear and moment in terms of the applied load P.c) Determine the maximum value of P such that bending failure will not occur.d) Determine the maximum value of P such that shear failure will not occur.e) Based on your answers to (c) and (d), what is the maximum load P that can be applied to the beam? Is this beam bending or shear governed?
Determine the horizontal component of the force applied by the smooth circular guide on the mass A. mA = 2 kg, y= 100 mm, Vy = 0.6 m/s, ay = -0.2 m/s^2
Determine the vertical displacement at Joint A, B, C, D, E
The horizontal rigid beam ABCD is supported by vertical bars BE and CF and is loaded by vertical forces P = 400 kN and P = 360 kN acting at points A and D, respectively (see figure). Bars BE and CF are made of steel (E = 200 GPa) and have cross-sectional areas ABE = 11,100 mm and Acr = 9,280 mm. The distances between various points on the bars are shown in the figure. Determine the vertical displacements & and dp of points A and D, respectively.