6.A hallow circular tube has an outside diameter of 85 mm andis 9 mm thick. The tube is fixed (cantilever) at one end andsubjected to a torque of 6 kN-m at its free end. What is themaximum shearing stress in the tube in MPa?A. 87.95C. 99.32Dendrwore as allodis monl beol99 qsB. 93.21D. 81.04D. BRIGHbru7. Give the following data of a rectangular beam:m00S=JBYOVE SHBeam width, b = 280 mmEffective depth, d = 390 mm19 loend5.84 ATension steel: five 25-mm-diameter$:08 18Compute the reinforcement ratio.eniersted asA. 4.12%ult bus textosid sC. 3.21%D. 2.25%bisgenal)B. 1.86%58.058.008.Given the following date of a steel column resting on steel baseplate:Column loads:Axial dead load = 1550 kNAxial live load = 950 kNConcrete 28-day compressive strength = 27.5 MPaAllowable concrete bearing stress = 0.35 fcWidth of base plate = 500 mmWhat is the minimum required length (mm) of base plate?A. 520C. 500B. 705D. 450

Answered: Image /qna-images/answer/0b20798f-b16b-4e41-851a-7953386a1b09.jpg

6. A hallow circular tube has an outside diameter of 85 mm and is 9 mm thick. The tube is fixed (cantilever) at one end and subjected to a torque of 6 kN-m at its free end. What is the maximum shearing stress in the tube in MPa? A. 87.95 Mode es 21lod C. 99.32 B. 93.21 3126754 D. 81.04 eds to cont 100e1=q229196 7. Give the following data of a rectangular beam: 00S=J imated 25 bns toolband Beam width, b = 280 mm Effective depth, d = 390 mm Tension steel: five 25-mm-diameter Compute the reinforcement ratio. A. 4.12% i entersis0 .as C. 3.21% di busgerald) B. 1,86% D. 2.25% TAZA SEAT A 16.05 28.01 8. Given the following date of a steel column resting on steel base plate: Column loads: Axial dead load = 1550 kN Axial live load = 950 kN Concrete 28-day compressive strength = 27.5 MPa Allowable concrete bearing stress = 0.35 f'c Width of base plate = 500 mm What is the minimum required length (mm) of base plate? A. 520 C. 500 B. 705 D. 450

6. A hallow circular tube has an outside diameter of 85 mm and is 9 mm thick. The tube is fixed (cantilever) at one end and subjected to a torque of 6 kN-m at its free end. What is the maximum shearing stress in the tube in MPa? A. 87.95 Mode es 21lod C. 99.32 B. 93.21 3126754 D. 81.04 eds to cont 100e1=q229196 7. Give the following data of a rectangular beam: 00S=J imated 25 bns toolband Beam width, b = 280 mm Effective depth, d = 390 mm Tension steel: five 25-mm-diameter Compute the reinforcement ratio. A. 4.12% i entersis0 .as C. 3.21% di busgerald) B. 1,86% D. 2.25% TAZA SEAT A 16.05 28.01 8. Given the following date of a steel column resting on steel base plate: Column loads: Axial dead load = 1550 kN Axial live load = 950 kN Concrete 28-day compressive strength = 27.5 MPa Allowable concrete bearing stress = 0.35 f'c Width of base plate = 500 mm What is the minimum required length (mm) of base plate? A. 520 C. 500 B. 705 D. 450

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The copper pipe [G = 5,000 ksi] has an outside diameter of 3.500 in. and a wall thickness of 0.250 in. The pipe is subjected to a uniformly distributed torque of t = 85 lb-ft/ft along its entire length. Using a = 2.5 ft, b = 3.5 ft, and c = 8.0 ft, determine(a) the maximum shear stress in the pipe.(b) the rotation angle φC at the free end of the shaft.
For the shaft shown, a. Determine the maximum stress on the shaft and the maximum angle of twist of end D relative to end A. b. If the stress in every section must not exceed 25 MPa, what should be the uniform diameter of the shaft? dAB = 100mm, dbc = 80mm, dcd = 50mm G for the shaft is 80GPa. Consider clockwise torques as negative.
Calculate the normal stress due to flexure at the flange level to web Interface at A. Ixx= 1,241 in^4. Bending moment (M)= 350 ft-kips. Shear (v)= 80 kips.
Very very Urgent The distributed load q and the singular moment M act on the stepped shaft given in the figure. Draw the cross-sectional influence diagrams of the system under these forces. Determine the maximum stress value for the critical section. L1 = 226 mm ,L2 = 118 mm, a = 159 mm M = 572 N.m, q = 5 N/mm D = 51 mm , d1 = 19mm , d2 = 5 mm
A spiral riveted pen stack 1.5-m in diameter is made of steel plate 10-mm thick. The pitch of the spiral or helix is 3-m. The spiral seam is a single riveted lap jointconsisting of 20-mm diameter rivets. Using a shear stress of 70 MPa and bearing stress of 140 MPa, determine the spacing of the rivets along the seam for a water pressure of 1.25 MPa. Neglecting the end thrust, what is the circumferential stress.
2.2 The hydraulic cylinder CF, which partially controls the position of rod DE, has been locked in the position shown. Member BD is 5/8 in. thick and is connected to the vertical rod by a 3/8-in.-diameter bolt. Determine (a) the average shearing stress in the bolt, (b) the bearing stress at C in member BD.
Member AB has a uniform rectangular cross section of 10 x 24 mm. For the loading Pshown,a) Find reactions at A and B.b) Determine the normal and shearing stresses at Point K and Point H. α (˚) =30 P (kN)=14
The stepped shaft ACB shown in Figure bellow is fixed at both ends and loaded by a torque TO at point C. Segment AC having solid circular cross section and segment CB having hollow circular cross section. If the shafts material is steel with shear modulus G = 11 x 10°psi, and the torque is To = 8,000 lb-in. Calculate: (a) The maximum and the minimum shear stress in segment CB. (b) The maximum and the minimum shear strain in segment CB. (c) The angle of rotation 0, at the cross section where the torque To is applied.
A solid steel shaft ABC of 50mm diameter is driven at A by a motor that transmits +50kW to the shaft at 10Hz. The gears at B and C drive the machinery using power equal to -35kW and -15kW, respectively. Determine the maximum shear stress in the shaft. Compute the angle of twist of the shaft between the motor at Ao and the gear at C.
The steel shaft with two different diameters rotates at 4.2 Hz. The power supplied to gear C is 68 kW, of which 42 kW is removed by gear B. Find the maximum shear stress (in Pa) in the shaft if d = 58.1 mm, h = 60.6 mm, L = 3.9 m, M = 2.1 m, and G = 83.49 Gpa. Round off the final answer to two decimal places
1) Calculate the effective depth of the section in PART B in mm.0 2) Calculate the depth of compression block of the section in PART B in mm. 3) Calculate the depth of the neutral axis of the section in PART B in mm. 4) Calculate the stress in the steel of the section in PART B in MPa. 5) Calculate the ultimate moment capacity of the section in PART B in kN.m.
A 5-m STEEL SHAFT ROTATING AT 2Hz HAS 70 KW APPLIED AT GEAR THAT IS 2m FROM THE LEFT END WHERE 20 KW ARE REMOVED.AT THE RIGHT END, 30KW ARE REMOVED AND ANOTHER 20 KW LEAVES THE SHAFT AT 1.5m FROM THE RIGHT END. (A) FIND THE UNIFORM SHAFT DIAMETER SO THAT THE SHEARING STRESS WILL NOT EXCEED 60 MPa. (B) IF A UNIFORM SHAFT DIAMETER OF 100mm IS SPECIFIED, DETERMINE THE ANGLE BY WHICH ONE OF THE SHAFTS LAGS BEHIND THE OTHER END. USE G = 83 GPa.