help me, i need answers. R1R2R3Three small light bulbs with internal resistances R1, R2, and R3 are arranged in aparallel and is connected to as 12-V power source. If the values of the internalresistances of the light bulbs are 1 Q, 4 0, and 3 Q respectively, find thefollowing:Voltage (V)Current (1)Resistance (R)TotalVtVIt ARt Q1V1V11 A102V2 V12 A3V3 V13 A30 R3 = 30R4 = 40R2 = 20R5 = 50R1 =10R6 = 60+7VSix resistors are connected to a 7V-cell as shown in the circuit above. Find thefollowing:Voltage (V)Current (I)Resistance (R)TotalVt VIt ARt Q1V1V11 A2V2 V12 A2Ω3V3V13 A3ΩV4 V14 A5V5 V15 A6V6V16 A

R1 R2 R3 Three small light bulbs with internal resistances R1, R2, and R3 are arranged in a parallel and is connected to as 12-V power source. If the values of the internal resistances of the light bulbs are 1 Q, 4 Q, and 3 Q respectively, find the following: Voltage (V) Current (I) Resistance (R) Total VtV It A Rt Q 1 V1V 11 A 10 2 V2V 12 A 3 V3 V 13 A a a 4. ww

R1 R2 R3 Three small light bulbs with internal resistances R1, R2, and R3 are arranged in a parallel and is connected to as 12-V power source. If the values of the internal resistances of the light bulbs are 1 Q, 4 Q, and 3 Q respectively, find the following: Voltage (V) Current (I) Resistance (R) Total VtV It A Rt Q 1 V1V 11 A 10 2 V2V 12 A 3 V3 V 13 A a a 4. ww

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Consider the following circuit in which V1 = 16 V, I1 = 8 A, R1 = 7 Ω, R2 = 5 Ω, R3 = 19 Ω, What is the Thévenin resistance between a and b?
Given the circuit below and that R1=1.7ohm,R2=3.5ohm,Emf1=2.1V and Emf2=6.3V. What is the current through the section ac?
You are required to analyze the operation of DC circuit shown in Fig.2 and apply Ohm’s law and Kirchhoff’s voltage and current laws to find all the Voltages (with the associated polarities) andcurrents (with the associated direction)for all resistors. (Show all steps, equations, and calculations). C)Your manager asked you to present an analysis for the scientific data related to DC circuit. Firstly, he asked you to replace V1 with open circuit and V3 with short circuit and do the following:a. Calculate the equivalent resistance, all currents and voltages.b. Connect the circuit in the Laboratory and fill the results in Table 2 (Show all calculations).
Let the following electrical circuits be, in which it is required to determine the value of the voltage V shown:Note that the two previous circuits are identical, the only difference is the load element that has been selected in each of them: in electrical network 1 the load element is resistor R3 while in electrical network 2 the element of load is resistor R1.a) Find, using Thévenin's theorem, the voltage V in electrical network 1.b) Find, using Thévenin's theorem, the voltage V in the electrical network 2.
Consider the following circuit in which V1 = 4 V, I1 = 14 A, R1 = 13 Ω, R2 = 13 Ω, R3 = 17 Ω, What is the Thévenin voltage between a and b with the indicated polarity?
d. If V2 = 8 V and E = 14 V, find V3. e. If R1 = 4 Ω, R2 = 2 Ω, R3 = 4 Ω, and R4 = 6 Ω, what is RT? f. If all the resistors of the configuration are 20 Ω, what is the source current if the applied voltage is 20 V? g. Using the values of part (f), find the power delivered by the battery and the power absorbed by the total resistance RT.
1. In a circuit that contains only resistors in series, the current is the same throughout the circuit (remember that current is conserved!). The amount of current in the circuit is determined by the potential difference (or em f) of the battery and the equivalent resistance, Req, of the circuit. We can therefore write Ohm's Law as DeltaV = IReq. Assume the batteries supply a potential difference of DeltaV = 3.0 V, and use the currents measured in circuits 3a, 3b, and 3c to determine the equivalent resistance in each circuit. Please show the calculation of each. R1 = 150 ohm, R2 = 230 ohm R3 = 270 ohms (don't believe question should need these but providing anyways) Current MeasuredCurrent through R1 in 3a (Only resistor 1) Ir1= 0.01 amp Current through R1 in 3b (Resistor 1 and 2) Ir1= 0.0032 amp Current through R1 in 3c (Resistor 1, 2 and 3) Ir1 = 0.002 amp
The node voltage equation for node b is to be expressed in the form: K=A⋅Va+B⋅Vb+C⋅Vc, where A, B, C, and K are constants. If K=3, what should be the value of the coefficient B? what will be the value of the coefficient C?
In some situations it is necessary to replace part of an electrical circuit. However, this must be carried out following certain criteria. The main one states that tension and current intensity, in the sector where the replacement occurred, must remain constant.In this we have what is known as the Substitution Theorem. For example, suppose that the circuit below it is necessary to replace the parts between terminals A and B. This will occur putting in their place a voltage source and a resistor. Calculate voltage and resistance that they must present.
4. The heating element in an oven has a resistance of R =32 ohms. One of thewires connecting the oven to the 220 volt power source is loose, contributingan additional r = 5 ohms to the closed-loop circuit. What is the power Povenradiated in the oven, and what is the rate Pcontact at which heat is dissipatedat the loose contact? The looser is the connection, the greater is the resistance r: What value of r is most likely to cause a fire. Also agraph showing Pcontact versus r
Determine the power dissipated the the variable resistor if RL is equal to 10 ohms. Also, find the current flowing in the 5-ohm resistor. Write your answer.
Using Kirchhoff's Rules, compute the current (mA) and voltage (V) values of the circuit if R1=2kΩ and R2=7kΩ.