QUESTIONSTEUse Kirchhoff's current law to calculating the total voltage (V;) of the power supply in thecircuit and the voltage drop across R2.1.R,=10KO1,=0.055A0.2AR=2.2KOR,=47022.From the following circuit, compute the current through R2,R3 and R4 and determine VAB. R,=1000125mABR-1200R=47003.From the circuit below, determine I1,12,13,l4 and Is200mA70mA35mA4.From the following circuit, calculate It and l2.4 k, 2000.1A||10.05A4-10V.600802800

1) Apply KCL at the node. 0.2=I2+I10.2=I2+0.055I2=0.145 A The voltage drop across resistor R2 is…

Answered: R,1002 125MA B A. R,=1200 R,=4700 3.…

R,1002 125MA B A. R,=1200 R,=4700 3. From the circuit below, determine I,,l2,13,14 and Is 200mA 70mA 35mA 4. From the following circuit, calculate I, and I2. 0.1A |0.05A 누10V. 800 600 802

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the circuit shown in figure below, Calculate V1, V2, I1, I2, I3, I4 and power dissipationthrough R4. ?
For the circuit shown in figure 2, assume that the voltage source (vs)is equal to 100 V and the current source (is) is equal to 12 A. Use the node-voltage method in your solution.Write out all equations and units in full 2.1) Bereken die spanning in volts by node V1. / Calculate the voltage in volts at node V1.2.2) Bereken die spanning in volts by node V2. / Calculate the voltage in volts at node V2.2.3) Bereken die stroom i1 in ampere. / Calculate the current i1 in ampere.2.4) Bereken die drywing in watt geassosieer met die onafhanklike spanningsbron. / Calculate the power inwatt associated with the independent voltage source.2.5) Bereken die drywing in watt geassosieer met die onafhanklike stroombron. / Calculate the power in wattassociated with the independent current source.2.6) Bereken die drywing in watt geassosieer met die afhanklike bron. Neem aan dat die spanning by nodeV1 gelyk is aan 66.133 V. / Calculate the power in watt associated with the dependent source. Assumethat the…
In the circuit shown, a 6-Ohm resistor connected in series to a parallel combination of two resistors, one is 30-Ohm and the other is R being unknown. Determine the value of R if: (a) the power dissipated in 6-Ohm resistor is equal to the power in the parallel combination; (b) he power in 6-Ohm is equal to the power of in R; (c) value of R maximum power transfer.Hint: To maximize power in R, use differentiation
Question 2 Two electric circuits, represented by boxes A and B, are connected as shown in the figurebelow. The reference direction for the current i in the interconnection and the referencepolarity for the voltage v across each interconnect are shown. For each of the following setsof values, calculate the power in the interconnection and state whether the power is flowingfrom A to B or vice versa. Part (A) i = 6 A, v = 30 V Part (B) i = −8 A, v = −20 V Part (C) i = 4 A, v = −60 V Part (D) i = −9 A, v = 40 V
1. Which resistance(s) has no effect on the value of vo? a. 4 ohms b. 260 ohms c. 16 and 260 ohms d. 40 ohms 2. What is the short circuit current (in amperes) when solving for the Thevenin equivalent circuit as seen by the 250Ω resistor? 3.Using superposition to get the Thevenin voltage (in volts) seen by the 250Ω resistor, what is the contribution by the 1A source?
For the circuit attached, by getting equivalent resistance and then using current and/or voltage division principles, calculate vx and the power absorbed by the 60-ohm resistor.
If they are defined as Vs=2V and Is=12A, respectively, in the circuit given below, how many volts will the Vx node voltage be? TIP: You might consider solving it with the Node Method. NOTE: Please enter your answer as 1 digit after the comma. Help me please... Thank you so much.
A 100 Vdc power source has an internal resistance of 75 ohms. If maximum power is to be transferred, what is the value of load resistance? 2. How much current will flow through the load resistance in Question 1? 3. What is the power dissipated by the load resistance in Question 1? 4. In Question 1, if the load resistance is doubled, how much voltage is dropped across the load? provide soln and answer asap
With switch SW1 and SW2 both closed, complete the following using the values from the table:i. Determine the total resistance in the circuit. ii. Determine the currents flowing in the circuit. iii. Determine the volt drops around the circuit. iv. Use the appropriate Kirchhoff’s law to confirm your results.
(a) Use Kirchhoff's and Ohm's laws in a step-by-step procedure to evaluate all currents and voltages in the circuit. (b) Calculate the power absorbed by each of the five elements of the circuit and show that the sum is zero.
Problem 1: Question A DC resistive circuit includes a 5.5 mA current source, ????, which is connected to 2 resistors in parallel: ??1 which is 7 kΩ and ??2 which has 1.75 times more conductance than ??1 . There is a closed switch before ??2 in series with only this resistor. The negative terminal of the current source is at ground. a) Draw the circuit diagram for the above described circuit being sure to label all circuit elements, current directions and voltage polarities of each element. b) The switch is now open. Redraw the circuit diagram with a voltmeter which measures the voltage across the resistor ??1. Be sure to label all circuit elements, current directions and voltage polarities of each element. Indicate the value displayed by the voltmeter.
A)Suppose component X is a wire. Find the equivalent resistance Reg of the resistor network over the source voltage Vs.B) Suppose component X is 5V battery and Vs = 10V. Using Mesh Analysis to find the in-loop current iA iB iC. Assume the -ve polarity of battery connected to bottom)C) Whhat is the power dissipated/supplied by X in the respective setting?