R17-1. The handcart has a mass of 200 kg and center of mass at G. Determine the normal reactions at each of the wheels at A and B if a force P = 50 N is applied to the handle. Neglect the mass and rolling resistance of the wheels. 60° 0.5 m 0.2 m 0.3 m 0.4 m 0.2 m

R17-1. The handcart has a mass of 200 kg and center of mass at G. Determine the normal reactions at each of the wheels at A and B if a force P = 50 N is applied to the handle. Neglect the mass and rolling resistance of the wheels. 60° 0.5 m 0.2 m 0.3 m 0.4 m 0.2 m

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter10: Fixed-axis Rotation

Section: Chapter Questions

Problem 71P: Two flywheel fo negligible mass and different radii are bounded together and rotate about common...

See similar textbooks

Similar questions

Repeat Example 10.15 in which the stick is free to have translational motion as well as rotational motion.
Rotational Inertia Problems 5 and 6 are paired. 5. N A system consists of four boxes modeled as particles connected by very lightweight, stiff rods (Fig. P13.5). The system rotates around the z axis, which points out of the page. Each particle has a mass of 5.00 kg. The distances from the z axis to each particle are r1 = 32.0 cm, r2 = 16.0 cm, r3 = 17.0 cm, and r4 = 34.0 cm. Find the rotational inertia of the system around the z axis. 6. N Use the information in Problem 5 to find the rotational inertia of the system around particle 1. FIGURE P13.5 Problems 5 and 6.
An automobile engine can produce 200Nm of torque. Calculate the angular acceleration produced if 95.0 of this torque is applied to the drive shaft, axle, and rear wheels of a car, given the following information. The car is suspended so that the wheels can turn freely. Each wheel acts like a 15.0-kg disk that has a 0.180-m radius. The walls of each tire act like a 2.00-kg annular ring that has inside radius of 0.180 m and outside radius of 0.320 m. The tread of each tire acts like a 10.0-kg hoop of radius 0.330 m. The 14.0-kg axle acts like a rod that has a 2.00-cm radius. The 30.0-kg drive shaft acts like a rod that has a 3.20-cm radius.
A potters wheela thick stone disk of radius 0.500 in and mass 100 kgis freely rotating at 50.0 rev/min. The potter can stop the wheel in 6.00 s by pressing a wet rag against the rim and exerting a radially inward force of 70.0 N. Find the effective coefficient of kinetic friction between wheel and rag.
The precession angular velocity of a gyroscope is 1.0 rad/s. If the mass of the rotating disk is 0.4 kg and its radius is 30 cm, as well as the distance from the center of mass to the pivot, what is the rotation rate in rev/s of the disk?
An electric sander consisting of a rotating disk of mass 0.7 kg and radius 10 cm rotates at 15 rev/sec. When applied to a rough wooden wall the rotation rate decreases by 20 . (a) What is the final rotational kinetic energy of the rotating disk? (a) How much has its rotational kinetic energy decreased?
Two flywheel fo negligible mass and different radii are bounded together and rotate about common axis (see below). The smaller flywheel of radius 30 cm has a cord that has a pulling force of 50 N on it. What pulling force needs to be applied to the cord connecting the larger flywheel of radius 50 cm such that the combination does not rotate?
An electric food processor comes with many attachments forblending and slicing food. Assume the motor maintains thesame angular speed for all the various attachments. The largestattachment has a diameter of 12.0 cm, and the smallest has a diameter of 5.00 cm. Find the ratio of the translational speeds of points on the edges of each attachment.
A 60.0-kg woman stands at the rim of a horizontal turntable having a moment of inertia of 500 kg m2 and a radius of 2.00 m. The turntable is initially at rest and is free to rotate about a frictionless, vertical axle through its center. The woman then starts walking around the rim clock-wise (as viewed from above the system) at a constant speed of 1.50 m/s relative to Earth. (a) In what direction and with what angular speed does the turntable rotate? (b) How much work does the woman do to set herself and the turntable into motion?
An automobile engine can produce 200 N m of torque. Calculate the angular acceleration produced if 95.0% of this torque is applied to the drive shaft, axle, and rear wheels of a car, given the following information. The car is suspended so that the wheels can turn freely. Each wheel acts like a 15.0 kg disk that has a 0.180 m radius. The walls of each tire act like a 2.00-kg annular ring that has inside radius of 0.180 m and outside radius of 0.320 m. The tread of each tire acts like a 10.0-kg hoop of radius 0.330 m. The 14.0-kg axle acts like a rod that has a 2.00-cm radius. The 30.0-kg drive shaft acts like a rod that has a 3.20-cm radius.
A cylinder with rotational inertia I1=2.0kgm2 rotates clockwise about a vertical axis through its center with angular speed 1=5.0rad/s . A second cylinder with rotational inertia I2=1.0kgm2 rotates counterclockwise about the same axis with angular speed 2=8.0rad/s . If the cylinders couple so they have the same rotational axis what is the angular speed of the combination? What percentage of the original kinetic energy is lost to friction?
A bus contains a 1500 kg flywheel (a disk that has a 0.600 m radius) and has a total mass of 10,000 kg. (a) Calculate the angular velocity the flywheel must have to contain enough energy to take the bus from rest to a speed of 20.0 m/s, assuming 90.0% of the rotational kinetic energy can be transformed into translational energy. (b) How high a hill can the bus climb with this stored energy and still have a speed of 3.00 m/s at the top of the hill? Explicitly show how you follow the steps in the Problem-Solving Strategy for Rotational Energy.