rectangular barge is 15 ft wide and 40 ft long and floats with a draft (submerged height) of 4 ft. It is piled so high with gravel that its center of gravity is 3 ft above the waterline. Is it stable with respect to its roll stability? The roll axis is parallel to the 40-ft side.

Q: If m = 30 kg and assuming rough surfaces, draw the free-body diagram. Cable A 0.1 m В 30°

A: Answer:  tension in the cable = 169.914 NFor a step-by-step solution have a look through the…

Q: A pontoon boat floats on two cylindrical pontoons (assume the ends are flat). Each pontoon is 6m…

A:

Q: B 12

A: N1,N2,N3,N4,N5,N6 they all are reactions at A,B and C

Q: . Assuming standard condition, what is the altitude in ft where the density is 0.001845 slug/ft3?

A:

Q: A barge is 15 ft wide and 40 ft long and fl oats with a draftof 4 ft. It is piled so high with…

A: Given data as per question Width of barge = 15 ft Length of barge= 40 ft Draft = 4ft let M is…

Q: A crane barge, 20 m long, 8 meters wide, and 12 meters high loaded at its center with a road roller…

A: Given DataWR=20×9.81×0.4536×200=176.58kNFB=dVy=8×1.2×20×9.81=1883.52kN

Q: Semicircular plate Calculate the fluid force on one side of a semicircular plate of radius 5 ft that…

A: given:

Q: The 2-in by 2-in by 12-ft spar buoy from  has5 lbm of steel attached and has gone aground on a rock,…

A: Given Data: The dimension of the spar is: 2 in X 2 in X 12 ft The weight of steel is: 5 lbm The…

Q: The ship with an average density p is sinking in a water reservoir with a depth of h. After what…

A: The forces on the ship as it is descending down the tank are shown in the Free Body Diagram(FBD)…

Q: In order to burgle a local McDonald's, the Hamburglar must climb onto the roof. To do this, a ladder…

A: Consider the diagram shown below for the given ladder.

Q: 8. An open, 2-ft-diameter tank contains water to a depth of 3 ft when at rest. If the tank is…

A:

Q: A square block (?? × ??) in a plan, has a height ?? and a relative density of 0.8.

A: Given Data Now draw the schematic diagram from the given problem Now for the stable equilibrium,…

Q: Consider a flatboat hull which carries cargo down a river. When fully loaded the craft weight 150…

A:

Q: Problem 6 A 6 meter high, 5 meter wide rectangular plate blocks the end of a 5 meter deep freshwater…

A: (a) To find: The resultant force exerted on the gate from the water. Given: The height of plate is…

Q: A box-shaped vessel 150 m. in length and 20 m. beam is floating at a draft of 7.0 m. in salt water…

A:

Q: An engineer trying to determine whether her crane will tip over when attempting to lift a 13K load.…

A: Given data as per question Load to be lifted = 13 k weight of counterweight = 15 k weight of crane…

Q: v of 50 m /s at the edge of a 100-m clif For the ball to reach the bottom of the

A:

Q: Please answer completely, step by step with brief explanation

A: Given data as per questionSGWood=0.6, 2 in by 2 in by 15 ftSteel=5lbmDensity of sea water,…

Q: A sliding gate of height 1.4m and width 2.8 lies in vertical plane that weighs 25kN. Determine the…

A:

Q: Q4: Three empty (130N ), (3m.) diameter drums are shown in Fig. 4. Neglect friction at all contact…

A: In a free body diagram, all the external forces acting upon the body are taken into consideration.…

Q: Q5: A jet engine airplane has a weight of 64 kN and wing area of 20 m². If the engine output be 8…

A: Given: Let us consider the given data,                 Weight, F=64 kN            Wing Area,A=20 m2…

Q: A car ferry is essentially rectangular with dimensions 25 ft wide and 300 ft long. If 60 cars, with…

A: Dimensions of ferry; Length L = 300 ft Breadth B = 25 ft Number of cars = 60 The average weight of a…

Q: "1 A solid timber (s=0.75) floats in oil (s=0.90). The base is a square 300 mm on a side. (5.a) Can…

A:

Q: Example: A hemisphere projection of diameter 0.6 m exists on one of the vertical sides of a tank. If…

A: Given:d=0.6 mhg=1.5 m

Q: Diagram of the problem, necessary formulas, clearance and numerical solution A sphere of radius 50…

A:

Q: A float sensor for the determination of the level of water in a vessel has a cylindrical float of…

A: given; mass(m)=2kgcross sectional area(A)=20cm2                                          =20*10-4…

Q: A float sensor for the determination of the level of water in a vessel has a cylindrical float of…

A:

Q: Statical Stability. The scow shown in Fig. A above is 15 m long, 6 m wide, and 4 m deep. It has a…

A:

Q: A pudding truck carries pudding with a density of 67.55 lb/ft! in a horizontal cylindrical tank with…

A:

Q: A rectangular barge is 15 ft wide and 40 ft long and floats with a draft (submerged height) of 4 ft.…

A:

Q: Plunger Cylinder A-5 in? Weight = 10,000 Ibf A- 500 in? 15 t

A: GivenW=10000lbCylinder of area A=500 in2Plunger of area A=5 in2F=?

Q: Explain, with the use of sketch diagrams, why the aerodynamic force on a blade has to be resolved…

A: The axial velocity will be higher for a blade that is at the upper half of the rotor disc instead of…

Q: A float sensor for the determination of the level of water in a vessel has a cylindrical float of…

A:

Q: A freshly cut log floats with one fourth of its volume protruding above the water surface. The…

A:

Q: Problem 1. What is the Ekman transport driven by a westerly wind of 9 m/s? The geographic latitude…

A: Given data as per questionSpeed of wind=9m/sGeographic latitude=35°NorthDensity of sea water,…

Q: A commercial ship entering port has a 1.25 m draught. It has a draught of 1 m after discharging its…

A:

Q: 2.2 A rectangular pontoon 10 m by 4 m in plan, weighs 280 KN and floats in sea water of density 1025…

A: Given data:-Plan area of pontoon, A=10×4m2weight of pontoon=280kNweight of tube=34kNdensity of…

Q: an oil drum of 500 mm diameter and 1.5 long is to be rolled across a footstep of 100 mm high.find…

A: Given Data: The diameter of the drum is, d=500 mm. The length of the rod is, l=1.5 m. The height of…

Q: The angle of the slope  23.0∘ and use a different cart and a different bucket. You observe that the…

A: Given data: Tension in the cable (T) = 175 N The angle of the slope α=23.0∘ Need to determine the…

Q: In a hydraulic car lift, the input piston has a radius of 2 cm and a negligible weight. The output…

A:

Q: When floating in water (SG = 1.0), an equilateral triangular body (SG = 0.9) might take one of the…

A: We have given When floating in water (SG = 1.0), an equilateral triangular body (SG = 0.9) might…

Q: A dam consists of a vertical concrete wall 8 ft high. When the water in front of the wall is 6 ft…

A: given,  height of the Dam ,- 8ft (H) height of the water level -6ft (h) Now,           Let the…

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.