Refer to the braced cut shown in the figure for which y= 20 kN/m², o'=23°, and c' = 0. 2.0000 The struts are located 5 m on center in the plan. Determine the strut load at A. 3.0000 3.0000 2.0000 A 1186.45 kN В 237.29 474 26 1816 29

Refer to the braced cut shown in the figure for which y= 20 kN/m², o'=23°, and c' = 0. 2.0000 The struts are located 5 m on center in the plan. Determine the strut load at A. 3.0000 3.0000 2.0000 A 1186.45 kN В 237.29 474 26 1816 29

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter15: Retaining Walls, Braced Cuts, And Sheet Pile Walls

Section: Chapter Questions

Problem 15.21P: Determine the factor of safety against bottom heave for the braced cut described in Problem 15.18....

See similar textbooks

Related questions

Q: Appraise the critical state soil mechanics concept. You may evaluate this concept in relation to the...

A: Critical state soil mechanics is the area of soil mechanics that encompasses the conceptual models t...

Q: The backsight to a BM is 3.125 m and the FS from the same instrument set up is 3.625 m. If the dista...

A: Given Data, Distance from level to BM = 3850 m Distance from level to TP = 4714.05 mCalculate the...

Q: A trapezoidal reinforced concrete beam of 11 m span is reinforced with steel having a total area of ...

Q: What is the amount of usage in hours per year if initial cost of bulldozer is Php 25.5 M with operat...

Q: Example 15.5 A square slab is simply supported on three sides and is free on the fourth side. If the...

Q: Calculate the volumes formed between the two mixed cross-sections given in the figure. (L= 30m)

A: Find the areas of cut and fill A1 (fill) Area A1 = Area of trapezium –Area of triangle ...

Q: A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate...

Q: A series of vane shear tests have been performed on a soft clay stratum. The results of these tests ...

Q: From the figure shown, determine the specific gravity of the log if the length is 6 m and the radius...

Q: On a sea-level standard day, a pressure gage, moored below the surface of the ocean (SG = 1.025), re...

A: Given data, Specific gravity of ocean water Sg = 1.025 Atmosphere pressure = 1atm = 0.101325 Mpa

Q: A pipe 2000 m in length witha flow rate of 2 m/s. At the end of the 600 mm pipe, a valve is provided...

A: Given, Pipe length (L) = 2000 m Flow rate (Q) = 2 m3/s Diameter (D) = 600 mm or 0.6 m

Q: what will be the delta for a crop when its duty is 650 hec/cumec on the field ?? If base period of t...

A: To determine the delta of crop for given duty and base period. Given, Duty of the crop (D) = 650 h...

Q: 4. What is the minimum diameter of a solid steel shaft that will not twist through more than 4º in a...

Q: A 5.0m simple beam supports the given floor loads Wu and a concentrated load Pu due to the wall tran...

Q: Mo 90 A 160 N/m Mo 380 N-m 200 N 4 m

Q: 1. Determine the maximum shear 2. Determine the maximum moment. Problem For the figure as shown belo...

Q: The A-36 steel W 6 x 20 column 6 m in height is pin connected at its ends and is subjected to the ax...

Q: A concrete dam retaining water is shown in the figure. If the specific weight of concrete is 23.5 kN...

A: We will calculate resisting moment and overturning moment.

Q: Q2: For the cantilever retaining wall shown below, calculate the factor of safety with respect to ov...

A: Calculate the factor of safety against overturning by the using following formula, F.O.S=MOMR ...

Q: Over a hydraulic drop structure in a river 22.8 m wide flows 170 m3/s. On the level apron of the str...

Q: The tractor-trailer unit is moving down the incline with a speed of 6.0 mi/hr when the driver brakes...

A: Estimate the percent increase n in the hitch-force component which is parallel to the incline, compa...

Q: # 3) A sand soll sample is subjected to a direct shear test under a normal load of 185 kPa. The spec...

A: Given Data : in the above question we have given;shere stress (S);ie; S=100KPanormal load(σn1);ie; σ...

Q: The common tangent of AB of a compound curve is 76.42 m, with an azimuth of 268°30'.The vertex V bei...

Q: Determine the net area of the given section below. Diameter of bolts is 7/8-in and the thickness of ...

Q: A column 3 m long and pinned at both ends is carries an axial load of 190 kN. The column is made up ...

Q: The planimetered areas of the contour lines represented a hill (70,80,90,100,110 m) A70= 116375 m2, ...

A: Given data : Area of first section A70=116375 m2 Area of last section A110=10100 m2 Area of even sec...

Q: 13mm mm 5mm 3mm wwg

Q: Situation 03. Joe wants to test how fast can SuperMan save him if he jumps of a cliff 180m high. He ...

Q: Find the maximum deflection for the cantilever beam loaded as shown in the figure if the cross secti...

Q: If a total station is set up at station K6 then station X was observed, calculate the Zenith angle a...

Q: A 2 m long steel wire is fixed and hanging vertically with a tensile load of 2 kN and causes it to s...

A: ##Determine the diameter ofthe steel wire ##

Q: 18.2 kN/m 36.4kN/m

A: To determine :- degree of static indeterminacy of the frame

Q: Two clean, parallel glass plates, separated by a distance d=1.5mm, are dipped in a bath of water. Ho...

Q: Strain profiles of a flexural reinforced concrete element section at yield and failure conditions ar...

Q: e misclosure in departure and latitude e -0.017m and -0.086m , respectively?

A: Given:- Traverse=2169.91metre misclosure in departure and latitude=-0.017m,-0.086m To find:- linear ...

Q: The mass specific gravity of a soil is 1.95, while the specific gravity of soil solids is 2.7. If th...

Q: Most Most Most Likely Preceeding Activity Optimistic Time Activity Pessimestic Time Time A None 2 4 ...

Q: A retaining wall 8 m high supports cohesionless soil having a dry density of 1600 kg/m³, angle of re...

Q: er experts to do , otherwise i will downvote The following series of standard penetration test ...

A: According to given data 18-ft thick stratum of relatively uniform silty sand: Groundwater table i...

Q: A man descends to the ground from an airplane with the help of a parachute which is hemispherical ha...

Q: A cantilever of length L' carries a concentrated load W at the mid-span. If the free end is supporte...

A: Given arrangement,

Q: For a given soil sample it has a sp.gr. of 2.74, moisture content of 16.6% and a moist unit weight o...

A: We have to determine the value of the void ratio of the soil according to the given data in the ques...

Q: Determine the deflection @C using DIM (Your final answer should be in "mm") 6 kN/m 3 kN A C D B 5 т ...

Q: A constant head permeability test was carried out on a cylindrical sample of sand 10 cm diameter and...

Q: Problem 1: A fluid having v = 4 x 10-5 m²/s flows in a 750 m long pipe having a diameter of 20

Q: 3. The plate as shown weighing 30 kN is raised by a cable sling. The cable sling has identical clevi...

Q: Tabulation 1 Weight of Cement Weight Cement Sample Sample (W1) 110 gm Fineness of Cement Sr.No. Reta...

Q: CRACK AND UNCRACKED STAGE OF CONCRETE 1. What is noncracked, linear stage? 2. What is cracked, linea...

A: Consider the simple supported beam depicted below, which is relatively lengthy. Assume that the load...

Q: For the properties of wide-flange refer to the attached table. TABLE B-2 Properties of Wide-Flange S...

Q: Subject/ Plates and shells theory Square Plate Caxa) simplysupported on all Face edges is Subjected ...

Concept explainers

Pressure and Stress

Question

Refer to the braced cut shown in the figure for
which y= 20 kN/m², o'=23°, and c' = 0.
2.0000
The struts are located 5 m on center in the plan.
Determine the strut load at A.
3.0000
3.0000
2.0000
A
1186.45 kN
В
237.29
474.26
D
1816.29

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Given: γ =17.5 kN/m3c = 30 kN/m2center-to-center spacing of struts in the plan = 5 m. Determine the factor of safety against bottom heave for the braced cut. Use Eq. (15.20) and assume the length of the cut, L 5 18 m. Use σ all = 170 MN/m2
Q1- A wall foundation( 1.3) m wide located at a depth of 0.8 m on a saturated soil hasaφ=26o,c=38kN/m2,γsat =19.90kN/m3andW.Tlocatedatadepthof0.8m. Calculate the allowable bearing capacity if the F.S = 3.5 and draw the pressure distribution under the foundation with a labeled sketch.
1. Find the resultant of tension F and Ta. 27.6 kNb. 37.2 kNc. 33.7 kNd. 44.6 kN2. What is the angle that their resultant makes with the horizontal rod OA? a. 28 degb. 37 degc. 33 degd. 44 deg3. Find the weight, W to prevent uplift. Use a factor of safety of 2.5. a. 49.23 kNb. 42.86 kNc. 59.51 kNd. 44.72 kN
A long braced cut shown is supporting a layer of clay. Angle of fraction is 0. The struts are placed 3m center to center. a.) Determine the reaction of the strut at B. b.) Determine the section modulus of wale at B if the allowable bending stress is 0.6Fy where Fy = 250Mpa
(a) Calculate the width of the wall that is compulsory to prevent the wall from sliding. Use yconcrete = 23.0 kn/m3, u = 0.75, FSS = 1.5. (b) Calculate the factor of safety against overturning. Neglect uplift pressure. Use 2 decimal places in every solved value.
The diagram is a three-hinged semi-circular arch. The horizontal component for the 30 kN force is? a. 15.98 kN b. 20.98 kN c. 25.98 kN d. 30.98 kN The vertical component for the 30 kN force is? a. 10kN b. 15 kN c. 18 kN d. 20 kN
What is the Vertical component (y-component) reaction force at support C? A. 600N, ( + ) upward B. 200N, (+) upward C. 600N,(-) downward D. 200N,( - ) downward SHOW SOLUTIONS
Determine the factor of safety against bottom heave for the braced cut described in Problem 15.18. Use Eqs. (15.66) and (15.70). For Eq. (15.70), assume the length of the cut, L = 18 m. 15.18 Refer to Figure 15.51 in which = 17.5 kN/m3, c = 60 kN/m2, and center-to-center spacing of struts is 5 m. Draw the earth pressure envelope and determine the strut loads at levels A, B, and C. FIG. 15.51
a) Draw the shear stress distribution of the section if there is a shear force on the sectionof 10kN.b) What percentage of the shear force is carried by the cross section between 2 and 3?
A slab shown supports the load W1 and W2 for every one-meter strip along the longitudinal section. If the total length L= 15m and W=145 kN/m, at what distance, in meters, from the left end will the shear in the slab be equal to zero?
The gate AB is 1 m long x 2 m wide, what is the F force on the gate in kN?
Determine the support forces and draw shear force diagram and bending force diagram L1=6m, L2= 5m a=2m, b=2m, c= 1m, d= 2m F= 10 Kn, P= 3 kN/m