Refer to the drawing that accompanies Check Your Understanding Question 14. Suppose that the voltage of the battery in the circuit is 3.8 V, the magnitude of the magnetic field (directed perpendicularly into the plane of the paper) is 1.0 T, and the length of the rod between the rails is 0.24 m. Assuming that the rails are very long and have negligible resistance, find the maximum speed attained by the rod after the switch is closed. Switch X Tx X Rod X X X X X X B (into paper)- X X X X X X X X

Refer to the drawing that accompanies Check Your Understanding Question 14. Suppose that the voltage of the battery in the circuit is 3.8 V, the magnitude of the magnetic field (directed perpendicularly into the plane of the paper) is 1.0 T, and the length of the rod between the rails is 0.24 m. Assuming that the rails are very long and have negligible resistance, find the maximum speed attained by the rod after the switch is closed. Switch X Tx X Rod X X X X X X B (into paper)- X X X X X X X X

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter13: Electromagnetic Induction

Section: Chapter Questions

Problem 13.1CYU: Chek sour Understanding A closely und coil has a radius of 4.0 cm. 50 turns, and a total ieslstancc...

See similar textbooks

Similar questions

12.7 Check Your Understanding What is the ratio of the magnetic field produced from using a finite formula over the infinite approximation for an angle of (a) 85°? (b) 89°? The solenoid has 1000 mins in 50 cm with a current of 1.0 A flowing through the coils
Check Your Understanding Consider using Ampere’s law to calculate the magnetic fields of a finite straight wire and of a circular loop of wire. Why is it not useful for these calculation?
Suppose you wish to produce 1.2-T magnetic field in a toroid with an iron core for which =4.0103 . The toroid has a mean radius of 15 cm and is wound with 500 turns. What current is required?
12.3 Check Your Understanding Using Example 12.3, keeping the currents the same in wires 1 and 3, what should the current be in wire 2 to counteract the magnetic fields horn wires 1 and 3 so that there is no net magnetic field at point P?
For calculating magnetic fields, what are the advantages and disadvantages of the Biot-Savart law?
A wire ismade into a circular shape of radius R and pivoted along a central support.The two ends of the sire are touching a banish that is connected to a &power source. The stricture is between the poles of a magnet such that we can assume there is a uniform magnetic field on the wire. In terms of a coordinate system with origin at the center ofthe ring, magneticfieldisBx=B0,By=Bz= 0. and the ring rotates about the z-axis. Find the torque on the ring siren it is not in the xz-plane.
A solenoid with an iron core is 25 cm long and is wrapped with 100 turns of wire. When the current through the solenoid is 10 A, the magnetic field inside it is 2.0 T. For this current, what is the permeability of the iron? If the current is turned off and then restored to 10 A, will the magnetic field necessarily return to 2.0 T?
What is the direction of the magnetic field that produces the magnetic force on a positive charge as shown in each of the three cases, assuming B is perpendicular to v?
Does increasing the magnitude of a uniform magnetic field through which a charge is traveling necessarily mean increasing the magnetic force on the charge? Does changing the direction of the field necessarily mean a change in the force on the charge?
A current of 1.5 A flows through the windings of a large, thin toroid with 200 turns per meter. If the toroid is filled with iron for which =3.0103 , what is the magnetic field within it?
Check Your Understanding The wire loop forms a full circle of radius R and current I. What is the magnitude of the magnetic field at the center?
The conducting rod shown in the accompanying figure moves along parallel metal rails that are 25-cm apart. The system is in a uniform magnetic field of strength 0.75 T, which is directed into the page. The resistances of the rod and the rails are negligible, but the section PQ has a resistance of 0.25 . (a) What is the emf (including its sense) induced in the rod when it is moving to tire right with a speed of 5.0 m/s? (b) What force is required to keep the rod moving at this speed? (c) What is the rate at which work is done by this force? (d) What is the power dissipated in the resistor?