Referring to the indeterminate beam shown below, the beam is pinned on A and B, while fixed supported on C. It carries uniformly distributed load w kN/m and point load of P kN (single arrow). By using slope deflection method, a) Derive the slope deflection equation at each joint b) Determine the end moment at each joint and sketch the BMD B 5m 2m 5 m Student El for each span Mwanza 15 EI

Referring to the indeterminate beam shown below, the beam is pinned on A and B, while fixed supported on C. It carries uniformly distributed load w kN/m and point load of P kN (single arrow). By using slope deflection method, a) Derive the slope deflection equation at each joint b) Determine the end moment at each joint and sketch the BMD B 5m 2m 5 m Student El for each span Mwanza 15 EI

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The beam as shown in Figure has a rectangular section with a depth of 250mm and width of 40mm. In addition to the point loads, the beam is also subjected to UDL having a magnitude of 176N/m acting at span from point B to free end. Calculate the slope and deflection at free end. Assume E = 200GPa. (Where P =88 KN )
Solve for the shear and moment equations. Also draw the fbds of the beam using the equation method (Fbd's for Vab,Vbc) as shown in the example below . Table content: FBD V1-2= (summation of Fv)L M1-2 =(summation of M)L X-Value Do not use the example. Just answer the beam with 80 kN/m and use the example as a basis when answering.
The system illustrated below is one of a beam ABCD, for which point A is ahinge, point B is supporting a downward load of 1000N, point C is connected tocable supporting a load of 275 N, point D is roller joint. The system is in static equilibrium, and you are asked to compute the verticalreactions at points A and D, assume that the weight of the beam is negligible. (I need help)
Given: fy = 345Mpa f'c= 28Mpa Beam as shown: 1. Determine the moment arm of the beam in mm 2. Determine the Nominal Moment Capacity in KN-m
The section of an I beam is made out of two identical flanges and a web. The width of Flange is 260mm and thickness 25mm. Web thickness is 10mm and the total depth of the section is 715 mm. fy=300mPa, ZX=5760X103 mm3 and SX=6390X103mm3. Determine the moment section capacity of the section
Consider the moment-resisting frame. Use the portal method of analysis. Use P2 = 4 kips P1 = 2 kips h = 11' b = 25' Provide all answers in kips and ft to two decimals. The sign convention is tension positive (unless noted otherwise). (both frames are the same for this problem) What is the shear force in the bottom beams (absolute value)? What is the horizontal reaction at H (absolute value)? What is the vertical reaction at I (tension positive)? What is the bending moment in the bottom beams (absolute value)? What is the bending moment in member FI (absolute value)?
Using Moment Distribution Method Analyze the given frame completely. For the uniform load acting at the beam members please compute for the loading using tributary area and load transfer. Unit Weight of Concrete=23.6 KN/cu.m. Second floor Slab thickness=200mm and Roof Deck thickness=150mm. Live Load= 1.90KPa. Use Total Floor Load=1.2DL + 1.6LL (Neglect Self Weight) ALL Beams use 2I and for Columns use I.
The indeterminate frame below is loaded with gravity loads as shown. Using MOMENT DISTRIBUTION METHOD, compute for the internal moments and moment reaction occurring on the structure due to the applied loads. Show your complete solution from the computation of distribution factor, fixed end moments, balancing, unbalanced moments and total joint moment for each member. Neglect effects of side-sway in the calculation. Use up to Bal5. Determine the FF. 1 Moment at joint E of column EH in kN-m. MEH 2. Moment at joint B of girder BC in kN-m. MBC 3. Relative stiffness of member BC. kBC 4. Distribution factor at joint A of girder AB. DFAB 5. Fixed end moment at joint D of girder DE in kN-m. FEMDE DONT FORGET THAT THE GIVEN VALUES ARE a=7.0 b= 23.5 c= 2.9 d= 5.2 e= 7.3 SHOW YOUR COMPLETE SOLUTION AND DRAWING. THANK YOU
A Z-shaped rigid bar ABCD, shown in the figure, issuspended by a pin at B, and loaded by a verticalforce P. At A, a 10-mm-diameter steel tie rod AFconnects the section to a firm ground support at F.Use E = 200 GPa. Determine the vertical deflectionat D.
Fixed end support at A and rollers at B and C . A concentrated load of 12 KN at the mid span of BC.Use slope deflection method and constant value of El with E= 200,000 MPa and 1= 400 x 106 mm^4. What is the moment MBC and MABin KN-m? 2 decimal places
9 -Loading status in figure q= 4 kN ⁄ m, P = 48 kN in the bar dimensions L= 2 m and e= 0.5 m. The cross-sectional effects at point E will be calculated. A is fixed, B is sliding joint bearing. Accordingly, the shear force at point E T=? a) 14B) 2C) 6D) 0E) 4
An indeterminate beam loaded a uniformly distributed load from A to B, from B to C, a linearly varying from 0 to 6 kN/m, is fixed at points A and C, and a roller at point B. The flexural rigidity is constant from A to C. Use E = 180 GPa, I = 1024 x 106 mm4Calculate the reactions and draw the shear and bending moment diagram for this beam using Slope Deflection Method.