Refrigerant 22 is the working fluid in a Carnot vapor refrigeration cycle for which the evaporator temperature is -30°C. Saturated vapor enters the condenser at 36°C, and saturated liquid exits at the same temperature. The mass flow rate of refrigerant is 10 kg/min. Determine the heat rejected to the condenser, in kW, A) 26.24 B) 28.45 27.90 D) 29.18

Refrigerant 22 is the working fluid in a Carnot vapor refrigeration cycle for which the evaporator temperature is -30°C. Saturated vapor enters the condenser at 36°C, and saturated liquid exits at the same temperature. The mass flow rate of refrigerant is 10 kg/min. Determine the heat rejected to the condenser, in kW, A) 26.24 B) 28.45 27.90 D) 29.18

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter22: Condensers

Section: Chapter Questions

Problem 7RQ: When a standard-efficiency air-cooled condenser is used, the condensing refrigerant will normally be...

See similar textbooks

Similar questions

When a standard-efficiency air-cooled condenser is used, the condensing refrigerant will normally be higher in temperature than the entering air temperature.
Define flash gas, and explain how it applies to the net refrigeration effect of the refrigeration cycle.
Condensers in these refrigerators are all_______cooled.
Refrigerant 134a is the working fluid in a solar power plant operating on a Rankine cycle. Saturated vapor at 60 degree Celsius enters the turbine, and the condenser operates at a pressure of 6 bar. The rate of energy input to the collectors from solar radiation is 0.4 kW per m2 of collector surface area. Determine the minimum possible solar collector surface area, in m2, per kW of power developed by the plant.
Refrigerant R134a is a working fluid in an ideal vapor-compression refrigeration cycle that communicate thermally with a cold region at 0 °C and a warm region at 26 °C. The fluid enters the compressor at 0 °C andleaves condenser at 26 °C. the mass flow rate of the refrigerant is 0.08 kg/s.Evaluate;i.the compressor powerii.The heat transfer of refrigerant andiii.Coefficient of performance, COP.iv.Compareand explainthe results above if the temperature of the cold region of refrigerant is -10 °C and pressure of condenser is 9 bar?
22 - Refrigerant – 134a (refrigerant, R–134a) is used in a refrigeration machine working with an ideal vapor compression cycle, the condenser is kept at 1000 kPa pressure and the evaporator is at 6ºC. If the cooling load is 450 kW, which of the following is the mass flow rate? a) 6.43 kg/h B) 3.07 kg/h NS) 3.39 kg/h D) 2.75 kg/h TO) 6.58 kg/h
In a Refrigerant 12 system which serves a 212 kw evaporator at - 30 0C. The system uses two stage compression with intercooling and removal of flash gas. The condenser temp is 400C . Given that, h2=356kJ/kg, h4=367kJ/kg Compute the following: a.) mass flow rate at low stage compressor (m1)ANSWER: 1.53661 kg/s b.) mass flow rate at high stage compressor (m3)ANSWER: 2.11791 kg/s c.) low stage compressor workANSWER: 27.43931 kw d.) high stage compressor workANSWER: 32.63926 kw e.) total compressor workANSWER: 60.078575 kw f.) COPANSWER: 3.52871 g.) heat rejected in the condenserANSWER: 272.07857 kw
Air enters the compressor of an ideal Brayton refrigeration cycle at 100 kPa, 270 K. The compressor pressure ratio is 3 and the temperature at the turbine inlet is 310 K. Determine:d).the coefficient of performance of a Carnot refrigeration cycle operating between thermal reservoirs at TC 270 K and TH 310 K, respectively. The above Brayton refrigeration cycle is modified by introducing a regenerative heat exchanger. In the modified cycle, the compressed air enters the regenerative heat exchanger at 310 K and is cooled to 280 K before entering the turbine. Determine for the modified cycle:(e).the lowest temperature, in K.f).the net work input per unit mass of air flow, in kJ / kg.
Refrigerant 22 is the working fluid in a Carnot vapor refrigeration cycle for which the evaporator temperature is -30°C. Saturated vapor enters the condenser at 36°C, and saturated liquid exits at the same temperature. The mass flow rate of refrigerant is 10 kg/min. Determine the a.) power developed by the turbine, in kW, b.) net power input to the cycle, in kW, c.) quality of refrigerant at inlet of compressor d.) the rate of heat transfer to the refrigerant passing through the evaporator, in kW, e.) refrigeration capacity, in tons, f.) net heat transfer in the cycle, in kW, g.) COP h.) the power input to the compressor, in kW, i.) the heat rejected to the condenser, in kW, j.) he net work in the cycle, in kW,
A standard vapor compression system produces 70.4 kW of refrigeration using R-12as a refrigerant while operating between a condenser temperature of 42 °C and anevaporator temperature of –25 °C.2.1 Draw the p-h diagram of the cycle. 2.2 Determine:(a) the refrigerating effect in kJ/kg, (b) the circulating rate in kg/s, (c) the power supplied, (d) the COP, (e) the heat rejected in kW, and(f) the volume flow rate in m3/s.
Considering a Rankine cycle: Why is it important to condense at leastuntil liquid saturated the fluid in the condenser?
The values of a vapor compression refrigeration cycle were given below. Calculate the values ofrefrigerant flow rate, refrigeration capacity, and the COP of the system.T1= Evaporator water outlet = 10 °CT2= Evaporator water inlet = 16 °CT3= Condenser water inlet = 16 °CT4= Condenser water outlet = 22°CCooling water flow rate = 1.5 L/minHeating water flow rate = 1.5 L/minEnthalpy of R134a in evaporator outlet = 305 kj/kg,Enthalpy of R134a in evaporator inlet =115 kj/kgEnthalpy of R134a in condenser inlet =327 kj/kg