Question 6 During an extrusion process, a chromium billet at a temperature of 1300°C, need to be extruded from a billet diameter of 13 mm to a final diameter of 0.35 mm. An extrusion die are required to withstand the temperature and forces occurring during the process. 6.1 Which ceramic material will you suggest for this application? Provide reasons for your selection. 6.2 If the ceramic material, selected in Question 6.1 have an UTS. = 915 MPa, porosity of 16% and n = 4, calculate the tensile strength and elastic modulus of the ceramic at room temperature.

Question 6 During an extrusion process, a chromium billet at a temperature of 1300°C, need to be extruded from a billet diameter of 13 mm to a final diameter of 0.35 mm. An extrusion die are required to withstand the temperature and forces occurring during the process. 6.1 Which ceramic material will you suggest for this application? Provide reasons for your selection. 6.2 If the ceramic material, selected in Question 6.1 have an UTS. = 915 MPa, porosity of 16% and n = 4, calculate the tensile strength and elastic modulus of the ceramic at room temperature.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The maximum principal strain failure criterion is appropriate for ceramic materials". Is this true or false?
For a powder binding process that mixes a 3:1 volume ratio mixture of semi-crystalline polyethylene powder with a density of 0.900 g/cm3 and crystalline polyethylene powder, what is the percent crystallinity of the manufactured parts? (The density of polyethylene in its amorphous and crystalline states is 0.870 g/cm3 and 0.998 g/cm3 respectively) a. % Crystallinity = 35.50% b. % Crystallinity = 55.25% c. % Crystallinity = 53.35% d. % Crystallinity = 61.20% e. % Crystallinity = 45.96%
A ceramic with KIc = 4 MPa m1/2 contains pores with radius a = 5 µm due to incomplete sintering. These pores lead to a decrease in the failure stress of the material in both tension and compression. One in every ten grainboundary junctions contains a void; the grain size of the ceramic is 50 µm. The ceramic fails in compression when the length ℓ of each crack generated at the voids equals one-half of the spacing between the voids. (a) Determine the compression strength of the ceramic, using the equation from Sammis and Ashby. (b) Determine the tensile strength of the ceramic, assuming flaws with size a.
GKN Sinter Metals Company pressed iron powders using a compaction pressure of 600 MPa to produced a cylindrical bearing which is 70 cm long and has internal and external diameters of 8 cm and 16 cm, respectively. Determine (a) the most appropriate pressing direction, (b) the required press tonnage to perform this operation, and (c) the final weight of the part if the porosity is 12%, given that the density of iron, ρ = 7.87 g/cm3. Assume shrinkage during sintering can be neglected
Define and discuss Blow molding Process in Metal and Plastic. Can blow molding be used in Glass materials yes or no? why?
The hull of the space shuttle consists of ceramic tiles bonded to an aluminium skin. Discussthe design requirements of the shuttle hull that led to the use of this combination of materials.Evaluate the major problems the designers and manufactures face while producing the hull of the space shuttle
If your aim is to obtain enhanced densification rates and accelerated grain growth during sintering, which sintering method would you prefer and why?What are the stages of this sintering method?
In 2018, 25% of produced flat glass were recycled back as a raw material in the production of flat glass as it yielded sustainable impacts such as the reduction of energy requirement to heat up the furnace since the mixture will melt easily. In your opinion, can other types of glass wastes (eg. tempered glass, glass bottles, etc) be used as a raw material in the production of flat glass. Justify your answer by providing references.
What is the effect of resolved normal stress on the yield behavior of crystalline metals and ceramics?
2) The part shown in Figure is to be pressed from fine copper powders using a compaction pressure of 1000 MPa. Dimensions are milimetres. Determinea) the required press tonnage to perform this operationb) the final weight of the part if the porosity is 15%. Assume shrinkage during sintering can be neglected. (the desity of copper =8,97g/cm3 )
Glass ceramics have low coefficients of thermal expansion. State why this is the case (hint; consider the microstructure) and then by means of a suitable diagram, describe and explain the thermal treatment employed in the production of glass ceramics.
What is an important consequence of time-temperature equivalence for testing of polymer time-dependent elastic moduli?