relation between the shear stress and rate of deformation is given in the figure, If the oil density is =270.5 kg/m what is its viscosity in (m /s)? Oil Oil 20 Rate of deformation, duldy Shear stress, T

relation between the shear stress and rate of deformation is given in the figure, If the oil density is =270.5 kg/m what is its viscosity in (m /s)? Oil Oil 20 Rate of deformation, duldy Shear stress, T

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 4. What is the kinematic viscosity of kerosene in ft /s at u=1.64centiPoise? Density of kerosene is…

A: Kinematic viscosity is directly proportional to dynamic viscosity. Kinematic viscosity is inversly…

Q: Consider the cylinder shown in the figure. We know that the cylinder is moving a load at 12 m/min as…

Q: Q5: The space between a square smooth flat plate (50 x 50) cm², and a smooth inclined plane (1:100)…

A: Given that , A=50×50 cm2=2500cm2y=0.01cmv=9m/sm=2.3kg=2300gmS.G=0.9tanθ=1100θ=0.573

Q: Jater is equalte What is Gage pressue of Wake - that is . hae piésluse of gasalin Gage pressne of…

Q: The torque M required to turn the cone-plate viscometer inFig. depends on the radius R , rotation…

A: According to the problem, the torque depends on the radius, rotation rate, cone angle, and…

Q: Oil, with kinematic viscosity of 0.001 m²/s is flowing inside the pipe network shown. The internal…

Q: The space between two square flat parallel plates is filled with oil. Each side of the plate is 0.85…

Q: Two plates are separated by 30 mm space. The lower plate moves at velocity of 2 m/s while the moves…

Q: Oil relation between the shear stress and rate of deformation is given in the figure, If the oil…

A: The relation between shear stress and rate of deformation is - τ=μdudyμ=τdudyThe slope of the graph…

Q: Two parallel plates, one moving at 4 m/s and the otherfi xed, are separated by a 5-mm-thick layer of…

A: Given data Velocity 'v'=4m/s thickness 'dy'=5 mm Specific gravity…

Q: The Reynolds number for a 1-ft-diameter sphere moving at2.3 mi/h through seawater (specifi c gravity…

Q: what is the relationship between the fluid viscosity and the drag force Fdrag?

Q: 3. A square block is weighing 300 N and having a length of 20 cm on one edge slips on a 20° inclined…

A: Given data: F=300 NL=20 cmθ=20°t=1 mm Need to determine the terminal velocity of the block down the…

Q: The density of the fluid is (1.05x10^3) kg/m3 and the dynamic viscosity is 1.12 x 10 - 3 Ns/m2. The…

Q: 2.20 Find the dynamic and kinematic viscosities of kerosene, SAE 10W-30 motor oil, and water at a…

A: Givenfluids at tmeperature 38oC1.kerosene 2.SAE 10W-30 motor oil3.water

Q: A piston with a diameter of 0.8 m and width of L=0.1 m rotates with 6 rad/s inside a cylinder that…

A: The given data are: L=0.1 mω=6 rad/sd=0.8 mD=1 mμ=8×10-3 N.s/m2

Q: In a stream of glycerine in motion, at a certain point the velocity gradient is 0.25 meter per sec…

Q: In an inclined open channel, a thin film of liquid is flowing down. The velocity aistribution of the…

Q: pllllzzzz help me right nowww plzzz The belt moves at a steady velocity V and skims the top of oil…

A: Given data: V= 3.5 m/s L= 2 m b = 60 cm h = 3 cm Need to determine the required belt-drive power.

Q: The space between two flat plates is filled with oil .Each plate has (60cm x 40 cm x 10 cm) and the…

A: Given Data Thickness of oil film is : c=1 mm Relative density of upper plate is : ρrel=50 Angular…

Q: Q4: A 7-cm diameter solid aluminum ball (SG palance nicely when submerged in a fluid as shown in…

Q: H.W2: two large plate surfaces are 2.4cm. the space between the surface if filled glycerine.what…

Q: (2) Referring to the following figure, the distance between plates is Ay = 0.5 cm, Av: = 10 cm/s,…

Q: What is Reynold’s number? What is its relevance in fluid flow. Define viscosity and ts properties.

A: It is required to define Reynolds number and viscosity

Q: 1) The velocity profile of a viscus fluid over a plate is parabolie with vertex 25 cm from the plate…

A: Given data: The distance between vertex and plate is, 25 cm The velocity of fluid at the vertex is,…

Q: The velocity distribution for the flow of oil with dynamic viscosity of 0.05 Pa-s is given by…

A: Given data: ● The dynamic viscosity of the oil: µ = 0.05 Pa•s ● The velocity distribution is given…

Q: (i) Discuss about Surface tension with the help of a diagram. (ii) Discuss about the different…

A: Surface tension:-

Q: The belt moves at a steady velocity V and skims the top of oil tank. Assuming a linear velocity…

Q: velocity distribution of the fluid is parabolic. higher the viscosity of the fluid, the higher

A: given:

Q: The space between two square flat parallel plates is filled with oil. Each side of the plate is 83…

Q: Define or describe each type of fluid: (a) viscoelastic fluid, (b) pseudoplastic fluid, (c) dilatant…

A: viscoelastic fluid: Viscoelastic fluids are a type of non-Newtonian fluid formed by a viscous…

Q: The device in Fig. is called a cone-plate viscometer. The angle of the cone is very small, so that…

A: Given: A cone plate viscometer sin θ ≈ θ Torque =M Radius=R To derive expression for μ

Q: A square metal plate 1.5 m side and 1.5 mm thick weighing 50 N is to be lifted through a vertical…

Q: 8. Piston A has a cross section of 1200 cm' while of B is 800 cm?. B is higher than A by 2m. If the…

A: Given data: AA=1200 cm2AB=800 cm2SG=0.8FB=4 kN Need to determine the pressure at the pistons A and B…

Q: The shear stress at a point in a liquid is found to be 0.03 N/m2. The velocity gradient at the point…

A: Given data: The shear stress is τ = 0.03 N/m2. The velocity gradient is dv/dx = 0.15 s-1.

Q: In Falling ball Viscometer, the density of the ball is p=7746.8 kg/m and its radius is 4 mm, the…

A: in a falling ball viscometer there is an equilibrium achieved between Gravitational pull, buouancy…

Q: A piston with a diameter of 0.8 m and width of L=0.6 m rotates with 6 rad/s inside a cylinder that…

A: Given data diameter of piston (d) = 0.8 m width (L) = 0.6 m ω = 6 rad/s diameter of cylinder (D) =…

Q: what will be the kinematic viscosity of an oil having density 888 kg/m. The shear stress at a point…

A: Solution is given below.

Q: Q1:: A 80 mm diameter of pipes and 300 mm long slides by its own weight of 1.7 kN inside a large…

Q: The velocity Panciple af fleuid flouing auer a flat plate is ginen by ginen whene U in in inches.…

A: Note - As per ur company guidelines we are allowed to answer the first question. Kindly post the…

Q: A piston with a diameter of 0.8 m and width of L=0.2 m rotates with 6 rad/s inside a cylinder that…

Q: A plate moving 10 cm/s to the right is 0.5 cm above a stagnant wall. The fluid between the plate and…

A: GIVEN DATA- U=10cm/s Viscosity =1.8cp Y=0.5cm we have to find shear stress

Q: For liquid viscosity measurement, it is desired to create a viscometer consisting of two 30 cm long…

A: L=30 cm=0.3 mdi=20 cm=0.2 mdo=20.2 cm=0.202 mT=0.13 NW=40 rad/s→VelocityV=ri.W = 0.2240 =…

Q: (viscosity of 0.01 kg/m.s and density of 1000 kg/m )

A: Solution : Given data : Re = 1600 hL = 24.3 mμ = 0.01 kg/ms ρ = 1000 kg/m3

Q: The relation between shear stress Z and velocity gradient dy/dx of a fluid is given by Z = A…

A: Data given- The relation between shear stress Z and velocity gradient dy/dx of a fluid is given by…

Q: Q3: A very lange thin plate is centered in a gap of width Co-o6m) with different oils of unknown…

Q: QI: The two concentric cylinders shown in the figure (1) are separated by an oil film with Viscosity…

A: GIVEN DATA VISCOSITY=0.023 kg/ms N=200rpm R1=15.12cm R2=15cm WE HAVE TO CALCULATE TORQUE

Q: 18. A 20 mm wide gap between two vertical plane surfaces is filled with an oil of specific gravity…

Q: Q1: Space between two square flat parallel plates is filled with oil. Each side of the plate is 55.5…

A: Given data as per question Side of plate = 55.5 cm Thickness = 1.15 cm = 0.0115 m Velocity = 15000…

Concept explainers

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.

Question

Oil relation between the shear stress and rate of deformation is given in the figure, If the oil density is =270.5
kg/m what is its viscosity in (m /s)?
Oil
20
Rate of deformation, duldy
Lenovo K9 Note
Al Dual Camera
Shear stress, 7

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

plzz help meeeeeeeeee The belt moves at a steady velocity V and skims the top of oil tank. Assuming a linear velocity profile in the oil, what is the required belt-drive power P (watt) (P= power = force x Velocity) if the belt moves at 3.5 m/s over oil with specific gravity of S=3.6 and oil viscosity of 0.004 m2/s. Belt geometry L= 2 m, b = 60 cm, and oil depth is h = 3 cm?
pllllzzzz help me right nowww plzzz The belt moves at a steady velocity V and skims the top of oil tank. Assuming a linear velocity profile in the oil, what is the required belt-drive power P (watt) (P= power = force x Velocity) if the belt moves at 3.5 m/s over oil with specific gravity of S=3.6 and oil viscosity of 0.004 m2/s. Belt geometry L= 2 m, b = 60 cm, and oil depth is h = 3 cm?
Two parallel plates, one moving at 4 m/s and the otherfi xed, are separated by a 5-mm-thick layer of oil of specific gravity 0.80 and kinematic viscosity 1.25 E-4 m 2 /s.What is the average shear stress in the oil?( a ) 80 Pa, ( b ) 100 Pa, ( c ) 125 Pa, ( d ) 160 Pa, ( e ) 200 Pa
The belt in the Ögure moves at steady velocity V and skims the top of a tank of oil having viscosity. (a) Develop and expression for the required belt drive power in terms of h, L, b, V , and . Recalthat, for steady motion, power is equal to force velocity.(b) What power is required if the belt moves at 5 m/s over SAE 50W oil ( = 0:86 kg/ms) withh = 2 cm, L = 2 m, and b = 0:5 m
Flat plate, moves at speed u0 over a fixed plate, with the intermediate layer consisting of oil. a) If the velocity profile isparabolic (u2 = a ∙ y) find the stress on the moving plate. b) What is its value if the velocity profile is linear.Result: α) τ=-μu0/2d, β) τ=-μu0/d
Q6) The space between two parallel plates is filled with oil. Each side of the plate is 60 cm. the thickness of oil film is 12.5 mm. The upper plate, which moves at 2.5 metre per sec requires a force of 98.1 N to maintain the Speed. Determine
In the study of fluid phenomena, how does Newton's Law of Viscosity affect your calculations?
In the textbook of Applied Fluid Mechanics (7th Edition), can the solution of problem 3.36 be explained to me more carefully? Not just what is given to me when I've looked. I'm having trouble understanding the material.
SAE-10 oil at 20 deg C fills the gap between the moving 6 cm diameter long cylinder which is inside a fixed outer cylinder 6.8 cm diameter. Calculate the pressure gradient per unit length needed so the shear stress on the outer cylinder is exactly equal to zero when the inner cylinder is moving with velocity V=4 m/s in the negative z-direction. Assume laminar flow. The viscosity of the oil is 99.2 cp. Express your result in kPa/m and round your numerical answer to a whole number
A torque is applied to rotate a cylindrical shaft (diameter D 1 , length L) at a constant angularspeed ω, inside a co-axial, stationary cylinder of the same length and diameter D 2. The gapbetween the bottom surface of the shaft and that of the stationary cylinder is h.(a) Develop a general expression of the torque in terms of the geometric dimensions andthe viscosity μ of an oil filling the gaps between the shaft and the stationary cylinder.Assume linear velocity profiles in all the gaps.(b) Determine the numerical value of the torque in the case of an oil of viscosity of 0.1Pa.s. [D 1=5cm, D 2=5.2cm, L=10cm, ω=50rpm, h=1mm]
Two infinite plates a distance h apart are parallel to the xzplane with the upper plate moving at speed V, as inFig. There is a fluid of viscosity μ and constant pressurebetween the plates. Neglecting gravity and assumingincompressible turbulent flow u(y) between the plates, usethe logarithmic law and appropriate boundary conditions toderive a formula for dimensionless wall shear stress versusdimensionless plate velocity. Sketch a typical shape of theprofile u(y).
The space between two parallel plates 0.001 ft apart is filled with oil viscosity 0.7cp. The top plate is stationary while the lower plate is moving in the x-direction with a velocity 1ft/sec. A. Determine shear rate B. What should be the shear stress in lbf/ft^2? Answer asap pls